CAVE-TEK TeamUp P20 User manual

CAVE-TEK TeamUp P20 Camera User Guide
CAVE-TEK
TeamUp P20 Camera
User Guide
English (V1.2)

CAVE-TEK TeamUp P20 Camera User Guide
Table of content
1Packing List 1
2Quick Start 1
3About P20 2
3.1 Interfaces and Buttons 2
3.2 Dimension 2
3.3 Remote Control 3
3.4 RS-232 Interface 4
3.5 Serial Communication Control 4
4GUI Settings 5
4.1 MENU 5
4.2 EXPOSURE 5
4.3 COLOR 6
4.4 IMAGE 6
4.5 P/T/Z 7
4.6 NOISE REDUCTION 7
4.7 SETUP 7
4.8 COMMUNICATION SETUP 8
4.9 RESTORE DEFAULT 8
5Network Function 9
5.1 Operating Environment 9
5.2 Equipment Installation 9
5.3 Internet Connection 9
5.4 Camera controlled by LAN 9
5.4.1 Setup IP address 9
5.4.2 Login IP Camera admin 10
5.4.3 Open Network stream with VLC player 11
5.5 Camera Setup 12
5.5.1 Homepage Introduction 12
5.5.2 Video Settings 14
5.5.3 Image Settings 15
5.5.4 Audio Settings 16
5.5.5 System Settings 17
5.5.6 Network Settings 17
5.5.7 Device Information 18

CAVE-TEK TeamUp P20 Camera User Guide
1
1 Packing List
Open the box, you will find below items:
Name
Quantity
TeamUp P20 Camera
1
AC Power Adaptor
1
Power Cable
1
RS232 Cable
1
USB Cable
1
Remote Control
1
Quick Installation Guide
1
2 Quick Start
1) Please check below connects first.
2) Connect the power adapter to the power connector on the rear panel of the camera. The power
indicator on the front panel of the camera is on.
3) After the camera is powered on, it starts to boot up to the initialization position. Then both horizontal
and vertical go to the middle position, the motor stops running, and the initialization is completed.
(Note: If preset 0 is saved, Camera will be moved to preset 0)

CAVE-TEK TeamUp P20 Camera User Guide
2
3 About P20
3.1 Interfaces and Buttons
Item
Name
1
LINE IN Interface
2
CVBS Interface
3
System Select Switch
4
RS485 Interface
5
RS232 IN Interface
6
RS232 OUT Interface
7
Network Interface
8
USB 3.0 Interface
9
USB 2.0 Interface
10
HDMI Interface
11
DC 12V Interface
12
Power Switch
3.2 Dimension

CAVE-TEK TeamUp P20 Camera User Guide
3
3.3 Remote Control
Key Description
1. Standby Key
Press this button to enter standby mode. Press it
again to enter normal mode.
2. Number Key
To set preset or call preset.
3. *Key
To configure the special function key.
4. Preset Key
Set preset: Store a preset position.
[SET PRESET] + Numeric button (0-9): Setting a
corresponding numeric key preset position.
5. HOME Key
Confirm the selection, or move the camera back to
the middle position
6. Return Key
Return to the previous menu
7. Zoom Key
Slow Zoom: Zoom In [+] or Zoom Out [-] slowly
Fast Zoom: Zoom In [+] or Zoom Out [-] fast
8. Left/Right Setting Key
Press with 1 button and 2 buttons setting the
direction of the Pan-Tilt.
●Simultaneously press L/R Set +1[STD]: set the
Pan-Tilt to turn the same direction as the L/R
Set.
●Simultaneously press L/R Set +2[REV]: set the
Pan-Tilt to turn the opposite direction as the
L/R Set.
9. Focus Key
To adjust the focus.
Press [AUTO] adjust the focuses on the center of
the object automatically. Or to adjust the focus
manually.
Press [MANUAL] adjusts the focus on the center of
the object manual.
10. Selection Key
Press the button corresponding to the camera you
want to operate with the remote controller.
11. #Key
To configure the special function key.
12. IR Remote Control Key
[*]+[＃]+[F1]: Address 1
[*]+[＃]+[F2]: Address 2
[*]+[＃]+[F3]: Address 3
[*]+[＃]+[F4]: Address 4
13. Reset Key
Clear preset: Erase a preset position.
[CLEAR PRESET] + Numeric button (0-9)
Or: [*]+[#]+[CLEAR PRESET]: Erase all the preset
individually.
14. PTZ Control Key
Press arrow buttons to perform panningand tilting.
Press [HOME] button to face the camera back to
front.
15. Menu Key
MENU: enter or exit OSD MENU.
16. Backlight Key
BLC ON/OFF: Press this button to enable the
backlight compensation. Press it again to disable
the backlight compensation.
17. PTZ Reset Key
Preset Pan/Tilt self-test.
18. Special Function Key
[*]+[＃]+[1]: Change OSD menu to English
[*]+[＃]+[4]: Display current IP address
[*]+[＃]+[6]: Reset to system defaults
[*]+[＃]+[8]: Display camera firmware Info.
[*]+[＃]+[9]: set mounting mode (normal / vertical
flip)
[＃]+[*]+[4]: Set Network configuration to DHCP
[*]+[＃]+[Manual]: Reset network to default.
[*]+[＃]+[F1]: Assign Camera to IR Address 1
[*]+[＃]+[F2]: Assign Camera to IR Address 2
[*]+[＃]+[F3]: Assign Camera to IR Address 3
[*]+[＃]+[F4]: Assign Camera to IR Address 4

CAVE-TEK TeamUp P20 Camera User Guide
4
3.4 RS-232 Interface
No.
Function
1
DTR
2
DSR
3
TXD
4
GND
5
RXD
6
GND
7
IR OUT
8
NC
The correspondence between the camera and
Windows DB-9 pin:
The correspondence between the camera and
the Mini DIN pin:
3.5 Serial Communication Control
●RS232 Communication Control
The camera is controlled via RS232. The RS232 serial port parameters are as follows:
Baud rate: 2400/4800/9600/38400 bit/s;
Starting Position: 1 bit
Data bit: 8 bits
Stop bit: 1 bit
Check digit: None
●RS485 Communication Control
Control camera via RS485, half-duplex mode:
Baud rate: 2400/4800/9600/38400 bit/s;
Starting position: 1 bit
Data bit: 8 bits
Stop bit: 1 bit
Check digit: None
●List of protocols
For a detailed list of VISCA/Pelco-D/Pelco-P protocols, please check www.cave-tek.com.
9.RI
8.CTS
8.NC
7.RTS
7.IR OUT
6.DSR
6.GND
5.GND
5.RXD
4.DTR
4.GND
3.TXD
3.TXD
2.RXD
2.DSR
1.CD
1.DTR
Windows DB-9
Camera
4.GND
4.GND
8.NC
8.NC
7.NC
7.IR OUT
6.GND
6.GND
5.RXD
5.RXD
3.TXD
3.TXD
2.DSR
2.DSR
1.DTR
1.DTR
Mini DIN
Camera

CAVE-TEK TeamUp P20 Camera User Guide
5
4 GUI Settings
4.1 MENU
Press the [MENU] button to display the main menu on the display, using the arrow button to move the
cursor to the item. Press the [HOME] button to enter the corresponding sub-menu.
MENU
Exposure
Color
Image
P/T/Z
Noise Reduction
Setup
Communication Setup
Restore Default
[Home] Enter
[Menu] Exit
4.2 EXPOSURE
Move the main menu cursor to [EXPOSURE], and press [HOME] key enter the exposure page, as shown in
the following figure.
EXPOSURE
Mode
Auto
ExpCompMode
Off
Backlight
Off
Gain Limit
3
Anti-Flicker
50Hz
Meter
Average
DRC
2
Select Item
Change Value
[Menu] Back
Mode: Exposure mode, Auto, Manual, SAE, AAE, Bright.
ExpCompMode: Exposure the compensation mode, On, Off (Effective only in Auto mode).
ExpComp: Exposure the compensation value, -7~7 (Effective only in ExpCompMode item to On).
Backlight: Set the backlight compensation, On, Off (Effective only in Auto mode).
Bright: Intensity control, 0~17 (Effective only in Bright mode).
Gain Limit: Maximum gain limit, 0 ~ 15 (Effective only in Auto, SAE, AAE, Bright mode).
Anti-Flicker: Anti-flicker, Off, 50Hz, 60Hz (Effective only in Auto, AAE, Bright mode).
Meter: Average, Center, Smart, Top.
DRC: DRC strength, 0 ~ 8.

CAVE-TEK TeamUp P20 Camera User Guide
6
4.3 COLOR
Move the main menu cursor to [COLOR], and press [HOME] key enter the color page, as shown in the
following figure.
COLOR
WB Mode
Auto
RG Tuning
0
BG Tuning
0
Saturation
100%
Hue
7
AWB Sens
High
Select Item
Change Value
[Menu] Back
WB-Mode: White balance mode, Auto, Indoor, Outdoor, One Push, Manual, VAR.
RG Tuning: Red gain fine-tuning, -10 ~ +10 (Effective only in Auto, One Push, VAR mode).
BG Tuning: Blue gain fine-tuning, -10 ~ +10 (Effective only in Auto, One Push, VAR mode).
Saturation: 60% ~ 200%.
Hue: 0 ~ 14.
AWB Sens: The white balance sensitivity, Low, Middle, High.
4.4 IMAGE
Move the main menu cursor to [IMAGE], and press [HOME] key enter the image page, as shown in the
following figure.
IMAGE
Luminance
6
Contrast
8
Sharpness
3
Flip-H
Off
Flip-V
Off
B&W-Mode
Off
Gamma
0.5
Style
Clarity
Select Item
Change Value
[Menu] Back
Luminance: 0 ~ 14.
Contrast: 0 ~ 14.
Sharpness: Auto, 0 ~ 15.
Flip-H: On, Off.
Flip-V: On, Off.
B&W-Mode: On, Off.
Gamma: Default, 0.45, 0.5, 0.56, 0.63.
Style: Default, Norm, Clarity, Clarity (LED), Bright, Soft, 5S.

CAVE-TEK TeamUp P20 Camera User Guide
7
4.5 P/T/Z
Move the main menu cursor to [P/T/Z], and press [HOME] key enter the P/T/Z page, as shown in the
following figure.
P/T/Z
SpeedByZoom
On
AF-Zone
Center
AF-Sense
High
L/R Set
STD
Display Info
On
Image Freeze
Off
Call Preset Speed
24
Select Item
Change Value
[Menu] Back
SpeedByZoom: The depth of field scale switch, On, Off.
AF-Zone: Interested in focusing area, Top, Center, Bottom.
AF-Sense: Automatic focusing sensitivity options, Low, Normal, High.
L/R Set: STD, REV.
Display Info: On, Off.
Image Freeze: On, Off.
Call Preset Speed: 1 ~ 24.
4.6 NOISE REDUCTION
Move the main menu cursor to [NOISE REDUCTION], and press [HOME] key enter the noise reduction page,
as shown in the following figure.
NOISE REDUCTION
NR2D-Level
Off
NR3D-Level
3
Select Item
Change Value
[Menu] Back
NR2D Level: 2D noise reduction, Off, Auto, 1 ~ 5.
NR3D Level: 3D noise reduction, Off, 1 ~ 8.
4.7 SETUP
Move the main menu cursor to [SETUP], and press [HOME] key enter the setup page, as below.
SETUP
Language
EN
DVI Mode
DVI
Lens
Type2
USB Mode
BULK
Auto Scan Shoot
Off
MJPEG Mode
420
[Home] Enter
[Menu] Back
Language: EN, Chinese, Russian.
DVI Mode: DVI, HDMI.
Lens: Type1, Type2.
USB Mode: BULK, ISOC.
Auto Scan Shoot: On, Off.
MJPEG Mode: 420, 422.

CAVE-TEK TeamUp P20 Camera User Guide
8
4.8 COMMUNICATION SETUP
Move the main menu cursor to [COMMUNICATION SETUP], and press [HOME] key enter the
communication setup page, as shown in the following figure.
COMMUNICATION SETUP
Protocol
VISCA
V_Address
1
V_AddrFix
Off
Net Mode
Serial
Baudrate
9600
Select Item
Change Value
[Menu] Back
Protocol: Control protocol type, Auto, VISCA, PELCO-D, PELCO-P.
V_Address: 1 ~ 7. (Effective only in Auto, VISCA protocol).
V_AddrFix: On, Off (When set to On, useless in 88 30 01 FF Command).
P_D_Address: 0 ~ 254. (Effective only in PELCO-D protocol).
P_P_Address: 0 ~ 31. (Effective only in PELCO-P protocol).
Net Mode: Set the serial port network control, Serial, Paral.
Baudrate: Serial port baud rate, 2400, 4800, 9600, 38400.
4.9 RESTORE DEFAULT
Move the main menu cursor to [RESTORE DEFAULT], and press [HOME] key enter the restore default page,
as shown in the following figure.
RESTORE DEFAULT
Restore?
No
Change Value
[Home] OK
[Menu] Back
Restore: Confirm restore factory settings, Yes, No.
Note: Press [HOME] button to confirm, all parameter restore default, include IR Remote address and VISICA
address.