Cecilware HDEHP User manual

Model HDEHP
HEAVY DUTY ELECTRIC SOLID HOT PLATE
10.8 30A - 240V (NEMA 6 - 30R)
Type Receptacle Req'd.
1 Phase Only
Amps 1 Phase Amps Per Line 3 Phase
3.9
5.2
KW
ELECTRICAL SPECIFICATIONS
18.7
21.7
16.3
18.7
9.4
L2Li L3
9.4
10.8
GENERAL SPECIFICATIONS
Width: 12.0" Depth: 24.0" Height: 11.5"
Thank you for purchasing this product.
To ensure proper use, we recommend that you
read this instruction manual before operating the
unit.
Dual voltage units - specify single phase or three phase.
"Cord supplied with 1 phase, NEMA-6.
Operation Manual
NQ17A December 2006
Volts
208
240

UNPACKING AND INSPECTION:
Carefully lift your Heavy Duty Electric Solid Hot Plate out of shipping container, and inspect immediately for
shipping damage. Install 4-inch legs as follows: Remove the legs from plastic shipping bag, turn your Heavy Duty
Electric Solid Hot Plate on its side and screw legs into the four holes provided in bottom.
NOTE: Your Heavy Duty Electric Solid Hot Plate was shipped in a carton designed to give it maximum protection
in normal handling. It was thoroughly inspected before leaving the factory and the carrier accepted and signed for it.
File any claims for shipping damage or irregularities directly with the carrier, not with company.
ELECTRICAL HOOKUP:
Insert Line Cord Plug into appropriate NEMA Receptacle as specified.
NOTE: A separate circuit should be supplied for each of these Hot Plate with a matched circuit breaker or fuse.
Check local codes for compliance in installation.
WARNING: WARRANTY IS VOID IF HOT PLATE IS CONNECTED TO ANY VOLTAGE OTHER THAN THAT SPECIFIED.
WARNING: INSTALL HOT PLATE AT LEAST 1" FROM WALL. DO NOT OPERATE HOT PLATE UNLESS LEGS ARE
INSTALLED.
Before using Hot Plate for the first time, heat up elements for three to five minutes to burn off protective coating. This
also hardens the surface of the solid heating elements.
** CLEANING INSTRUCTIONS **
The solid heating elements are easily cleaned with a damp cloth after use. Clean up dirt and spills with Ajax and a
Scotchbrite pad. After cleaning, rub a few drops of cooking oil into the surface of the elements; then switch on for a
few minutes to re-harden. Hot Plate
Use Ajax and a Scotchbrite pad to keep the exterior surfaces of your short order Hot Plate free of dirt and blemishes,
rubbing with the grain of the stainless steel. Rinse and wipe dry; then polish with a soft cloth.
These simple procedures will keep your short order Hot Plate clean and sparkling. A well cleaned Hot Plate will give
you many years of service.
A circuit diagram has been provided to assist qualified technicians. A Recommended
Qualified Service Technician should carry out repairs if needed. Do not remove any
components or service panels on this product.

Item Part No. Description
102315 Handle - Chrome 202316 302318
Thermostat Knob
4 502314 6
02319 Power Switch
02320 Solid Heater Element
7Power Cord
Indicator Light - Green 4" Adjustable legs (set of 4)
1
FRONT PANEL REMOVED
2 3 5
4
4BOTTOM PANEL REMOVED 67
** SPARE PARTS LIST **
C097A

0 1 2 3 4 5 6
5 2 1 3 3 4
P3 P1 P2
SWITCH
P3 P1 P2
34215 K1
HL1
EH1
K2
HL2
EH2
L1 L2 GND
EH1 - 2: STOVE HEAD K1 - 2: SWITCH HL1 - 2: LED
P3 P1 P2
34215
850 450
1300
850 450
1300
HEAVY DUTY ELECTRIC SOLID HOT PLATE
WIRING DIAGRAMS
240 VOLTS - 60 Hz. - 1 PH. - 5.2 kW.
L1, L2, + GND
Model: HDEHP
NE285