Cerio SP-800 User manual

CERIO Corporation
Network Control Server
(SP-800)
Quick Installation Guide

1. Introduction
CERIO's Web authentication device of the special use network control server (SP-800), the SP-800
must connect printer. Administrator can use SP-800 to generate a new account for the remote
control Cerio's Web authentication device and print authentication account. You can refer to
SP-800-PRINTER and SP-800-QRCPRT for Cerio's .
2. Product Outward Appearance
1 2
3
4
(1) LED Indicator
Power: Power LED.
Status: Status LED, LED lights up status is working
Lock: Button lock LED. A light up status is locking.
Link/Act: Network connection status. A LED light up status is
connecting.
100M: Ethernet use 100Mbps will light up.
(2) Function number display.
(3) Control buttons.
- / + : The buttons can control number for increase or reduce,
number display with set Cerio’s Controller function dependent.
Print out: Click the button will print account ticket.
FUNCTION button:
Lock function: Press and hold about 5 seconds the Lock LED will
light up, it represents the key has been locked.
Locked eliminate function:Press and hold about 5 seconds the
Lock LED will off, it represents the key locked eliminate
Connection test function:After click "Function" button will
display number 1 and click "Print out" button the system can
print test information this means has completed.
Print information for Qty: Click "Function" button and select
number 8 or 9 can printer account Qty. No.8 can print “Early
Balance”. No.9 can print “Current Balance” information.
CANCEL: Clears “Function” events
REPEAT: Print the previous ticket.
(4) Console 1-2 Port
Product Front
5
6
7
(5) RJ-45 Ethernet Port
(6) Screw Terminal Block
(7) DC-JACK power port

3. POS system application architecture for Hot spot
Cerio's Web authentication POS system contains Controller + SP-800 + Thermal printer and Cerio’s
Access Point etc.
Cerio's controller mounted SP-800-PRINTER for POS system application diagram.
Cerio's controller mounted SP-800-QRCPRT for POS system application diagram.

4. Login management interface for SP-800
Network control server(SP-800)built-in web management interface. After install POS system
architecture, administrator can use network connect to SP-800 interface and management.
The SP-800 manager URL is http://192.168.2.253/setting.htm, please open IE or Firefox
browser and enter URL address to set function.
COM1 Setting: Recommend use default。
Network Setting:
Enable DHCP: Administrator can select enable or disable DHCP client.
Static IP Address: Administrator can set IP address for SP-800.
Static DNS Server: Administrator can set IP address for DNS server.。
Transmit Timer: system to detect controller connect status (millisecond).
Server Listening Port: SP-800 connection to controller use Port. (SP-800 and
controller must be set the same port).
After setting is complete, please click Apply button.

5. Install normal thermal printer
# Install step for thermal paper
1) Open the cover for thermal printer
2) Place the thermal paper in the printer groove
3) After pull the paper out a small portion please
close the lid for thermal printer 1
2
3
1) SP-800 connection to thermal printer use
console port
2) DC Power in.
3) Power on/off switch.
1
2
3

6. Install QR Code thermal printer
Behind the printer connection functions support USB / console / RJ-45 /RJ-11 and Powe r.
As follows
PS. Connect the controller only need to use RJ-45 and power.
# Login web page for QR Code printer.
The QR Code printer support web management interface, administrator can login web page
and modify IP address for the QR Code printer.
QR Code Printer default IP address: 192.168.123.100
As follows
USB Port Console RJ-45 RJ-11 DC in

# Install or Replace Paper Roll for QR code printer
1) Pull the Cover Release Button to open the Cover.
2) Roll out and install the Paper Roll with Holder into the Printer. (with the edges of the
paper roll holder fitted onto the holder slots)
79.5mm size for thermal paper
57.5mm size for thermal paper
When using a paper roll in
smaller width, install the Paper
Width Guide first, and then
install the paper roll with holder.

3) Please close the lid for thermal printer.
＃
DIP Switch Setting for QR code Printer
DIP Switch in printer bottom.
DIP Function ON OFF
1 Paper Cutter No Yes*
2 Audio Alarm Yes * No
3 Print Density Dark Light *
4 Two-byte Character Code *No Yes
5 Character Per Line 42 48 *
6 Cutter with Cash Drawer Yes No *
7 & 8 Baud Rate Setting --- OFF*
# Baud Rate Setting (DIP 7, DIP 8)

7. Set web authentication steps for POS system
Cerio’s Web Authentication System consists of the controller and SP-800 + Printer; administrator
can use SP-800 remote control Cerio’s controller to create an account and print out.
The architecture can refer to “3. POS system application” description
Set web authentication steps, as follows
(Take Cerio’s DR-3000 as the case)
Steps1
Login SP-800 web interface to set IP address and set same network segment
You can refer to “ Login management interface for SP-800”4.
Steps2
If SP-800 with QR code Printer, administrator must set IP address for QR code Printer (same
network segment for your network). You can refer to “ ”6. Install QR Code printer
Steps3
Login Cerio’s Controller “DR-3000” page (Refer controller user manual) to enable RADIUS Server.
As follows
Please click menu “Account””RADIUS Server”for Cerio’s DR-3000
Steps4
Set the connection between DR-3000 and SP-800. Please click menu “Account”” Thermal
Printer Setup” to enable function, as follows

IP address: Please enter IP address for SP-800 (You can refer to 4. Login SP-800)
Command port: Please enter Command for SP-800 (You can refer to 4. Login SP-800)
Printer Type: Administrator can select Printer for normal or QR Code Printer.
QR code Printer
：
If select QR Code printer, administrator must choose use
connection for IP address or com Port.(Recommend use IP address manner.)
Printer IP Address
：
Please enter IP address for QR code printer. (You can refer
to 6. Install QR Code Printer).