Chef-Master HEF605 User manual

1
HEF605 Water Boiler
Instruction Manual

2
Contents
1. Information.......................................................................................................................3
1 Introduction.........................................................................................................3
2 Safety.................................................................................................................3
3 Electrical Installation Procedure...........................................................................4
4 Plumbing Installation Procedure..........................................................................4
5 Backflow Prevention............................................................................................4
6 Maintenance.......................................................................................................4
7 Descale Procedure.............................. ................................................................4
8 Limescale............................................................................................................4
9 Disposal..............................................................................................................5
10Compliance.........................................................................................................5
11 Operating the Boiler for the First Time.................................................................5
2.Installation........................................................................................................................6
3.InstallingFilter...................................................................................................................7
3. Operating Boiler................................................................................................................8
4. Service Set Up..................................................................................................................9
1 Changing Temperature........................................................................................9
2 Filter Mode........................................................................................................10
3 Changing from C/F.............................................................................................11
4 Heat Fill Selection..............................................................................................12
5. Cleaning & Maintenance...................................................................................................13
7. Troubleshooting...............................................................................................................14

3
Introduction
The information provided in this manual is intended to assist in the installation and maintenance of the
MT range of hot water boilers. Please read the instructions carefully to prevent accidents and ensure an
efficient installation. This manual is not a substitute for any safety instructions or technical data affixed
to the machine or its packaging. All information in this manual is current at the time of publication and
is subject to change without notice. The company accepts no responsibility for any damage or injury
caused by incorrect or unreasonable installation and operation.
Safety
When using electrical appliances, basic safety precautions should always be followed to prevent the risk
of fire, electric shock, burns, or other injuries or damages.
• Read all operating and safety instructions carefully.
• This appliance is not suitable for outdoor use.
• This appliance must be placed/installed on a horizontal flat stable surface.
• The ambient temperatures this appliance should operate within are 5 °C - 35 °C.
• Do not store the appliance in ambient temperature lower than 5 °C.
• This appliance is designed for use in self-service areas in which it can be attended to by trained per-
sonnel.
• Only the water hose supplied with the machine should be used to connect to the mains water supply
• The hose supplied with the boiler is non-toxic food quality. However, a hose is not a permanent con-
nection. It is, therefore, advisable to switch off boiler and close the stopcock valve when boiler is not in
use, e.g. overnight etc.
• If a non-fixed water connection is implemented, use only the water hose provided with the appliance,
alternatively, if a fixed water connection is used it must be implemented using a non-detachable water
hose.
• If the water hose is disconnected the seals should be replaced before re-connection.
• Risk of scalding. Beware of accidentally operating the water draw off tap especially when cleaning the
front of the boiler.
• The utmost care has been taken in the manufacture and testing of this machine. Failure to install,
maintain and / or operate this machine according to the manufacturer’s instructions may result in con-
ditions that can cause injury or damage to property. If in any doubt about the serviceability of the ma-
chine always contact the manufacturer or your own supplier for advice.
• This machine is not intended for use by persons (including children) with reduced physical, sensory,
or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the machine by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the machine.
• In the event where any wires are damaged, such wires can only be replaced by qualified service tech-
nicians.
• CAUTION - Risk of fire and electric shock. Only to be used with manufacturer’s specified power cord set.
Marco p/n 1501487 (USA), 1501488 (EU), 1501489 (UK/Ire).
• This appliance should not be installed in an area where a water jet could be used to clean it.
• Access to the service area of the appliance is restricted to persons having knowledge and practical
experience of the appliance and the relevant safety and hygiene requirements.
Information

4
Information
Electrical Installation Procedure
Electrical specification: 2.8kW 200-230Vac 50Hz
When installing the machine, always observe the local regulations and standards. The ap-
pliance is supplied with a moulded power cord. A suitable mains power supply socket should
be available within easy access of the appliance so that it can be disconnected easily after
install.
Plumbing Installation Procedure
• Ensure that the equipment is installed according to local plumbing & water regulations.
• Mains water pressure required (limits): 100-500kPa, 0.1-0.5MPa (14.5-72.5psi).
• Fit a stop valve on a cold water line and attach a 3/4” BSP male fitting,
(E.g. 3/4” x 1/2” or washing machine type stop valve).
• Turn on the water to flush any impurities, dust etc from the inlet hose and water pipe. Allow
several litres through. Especially for new installations.
• Connect the hose to the inlet valve of the boiler. Make sure a sealing washer is fitted.
• Turn on water and check for leaks.
• NOTE: Using a non-food grade hose (e.g. a washing machine hose) will usually result in off
tastes & smells in the water and can possibly be toxic.
• Do not connect the machine to pure reverse osmosis water or other aggressive types of
water.
Backflow Prevention
This equipment must be installed with adequate backflow protection to comply with all ap-
plicable federal, state and local codes.
Maintenance
This machine has been designed to give many years of trouble free service. The only regular
maintenance required is occasional de-scaling.
Cleaning
The exterior of these machines may be cleaned with a damp cloth and a light detergent.
Do not use abrasive cloths or creams, as this will spoil the finish of the machine.
Do not use a water jet or spray.
NOTE: Beware of accidentally operating the draw off tap when cleaning the front of the ma-
chine.
Limescale
In common with all water boiler manufacturers, service calls resulting from limescale are
not covered by warranty. For units without a water filter fitting an external scale reducer
is recommended, especially in hard water areas. This can reduce the build-up of scale but
may not stop it altogether. The frequency that descaling is required depends on the local
water supply; hard water areas need more attention. Descaling of the machine should be
carried out by qualified service personnel.

5
Disposal
Under WEEE regulations this product must not be disposed of as household waste. To prevent
damage to the environment and humans this product must be disposed of in an approved
and environmentally friendly recycling process. For more information on how to dispose of
this correctly please contact your Chefmaster distributor or local authority responsible for
waste disposal.
Compliance
All Chefmaster parts and products have undergone a stringent testing process to ensure that
comply with all European standards and specifications.
All Chefmaster products carry the CE approval symbol.
Operating Boiler For The First Time
1. Check that all installation procedures have been carried out, see the following page.
2. Ensure water valve is connected
3. Plug in the IEC connector to the boiler.
4. On models with a filter, connect the filter.
3. Plug boiler into suitable socket.
4. The boiler will power up.
5. The screen will show the software revision.
6. The machine will then fill with water and the display will flash between E-2 & the current
temperature of the tank, until the water has reached the low level probe, then it will show
the current water temperature.
7. The default temperature is 95°C.
8. Once the machine is up to temperature the boiler is now ready for use.
NOTE: Because the boiler is electronically controlled no priming is necessary.
The element cannot switch on until a safe level of water is reached.
Information

6
Installation
1.
Software revision.
Revision can change
in future.
2.
3.4.
¼” tube
(6.35mm)

7
Installing Filter
1. 2.
3.
The orientation indicator on the filter should point left
before rotating
8000781

8
E-2
Tank Filling;
water under low
level probe
Tank filling
1. 2.
Operating Boiler
3.4.
Diagram of Parts
1Screen
2Standby Button
3Tap
4Drip Tray
1.
2.
3.
4.

9
Service Set Up
Changing Temperature
5 sec
Add one degree
Range 60 - 97°C
5 sec
1. 2.
3.
To save value

10
Service Set Up
Filter Mode
10 sec
Add 2 units.
Each unit is 200L.
Setting to “00”
disables the flag.
5 sec
2.
1.
3.
The machine estimates
how much water goes
through the system
& triggers a filter flag
if a filter change is
required.

11
Service Setup
Changing from Celcius to Farenheit
Switch between
C/F
5 sec
1. 2.
3.
15 sec
203 = 203F
4.

12
Service Set Up
Heat Fill Selection
20 sec
Switch between:
H-F (Heat Fill)
C-F (Continuous Fill)
5 sec
2.
1.
3. Heat Fill (default & recommended setting)
The inlet valve lets in a small fixed volume of water and the
element turns on heating the water to the set tempera-
ture. This process is repeated until the water has reached
the high level probe and the machine is up to tempera-
ture.
Continuous Fill
The inlet solenoid stays open until the water has reached
the high level probe. Simultaneously the element stays on
until the machine is up to the programmed set tempera-
ture.

13
Cleaning & Maintenance
1. 2.
3.4.
Cleaning max temp 65°C

Troubleshooting
The screen of the boiler indicates various errors or problems with the machine. See diag-
nostic table below for futher details.
Error Description Action
E-1 High level probe is detected but low level
probe is not detected.
Descale machine & low-level probe.
If it persists, call service agent.
Check low level probe is wired.
Check high & low level are not switched.
E-2 Low level probe not detected. Wait for machine to ll.
If water can be dispensed then the probe
may be covered in limescale, -descale
machine.
If descaled and error persists then call
service agent.
Check low level probe is wired.
E-3 Temperature sensor (thermistor) is faulty,
missing or not plugged in.
Call service agent.
Thermistor has an open circuit.
E-4 Water is not heating Element has failed, Call service agent.
Check element for resistance which
should be approx 19 Ohms
E-5 Temperature sensor (thermistor) is faulty Call service agent.
Thermistor has a short circuit.
E-6 No incoming water Check water supply is turned on and
mains pressure is above 1bar (14.5psi)
If water supply is OK call service agent as
the inlet valve has likely failed.