Chef Snow CRE-170A User manual

www.crechef.co.kr
Contact point forA/S
Manufacturer : 82-1577-4692
or Local dealer in your country
Operation Manual
CRE-170A
Snowflake-Ice machine (Brand Name : Chef Snow)
* Be sure to read "Cautions for Safe Use" before using it correctly.
* Please read it and keep it in a place that anyone can see at any time.
* Available overseas market after checking the exact power source
in country side (Hz, Voltages, Phase).
* The performance and design of this product may be changed without
notice for quality improvement.

32
Safety instructions
1. Unless someone is responsible, guided and supervised for safety, physical and
mental defects or if clients are children or have little experience or knowledge, do
not use the product. Please supervise children not to play with the product.
2. This product is not used in accordance with the improper use or instruction
manual. Manufacturer is not responsible for damages or injuries, nor is the
product warranty.
3. Children should not use, clean or maintain without supervision.
4. Please use the outlet for the product plug, and the voltage
Must be the same. Damage due to improper use is subject to warranty does not.
5. If you want to extend the cord, be sure to use only grounded cables.
6. Pull the power cable over a sharp edge or keep it away from heat and humidity.
7. Please stop using the product and ask for A / S in the following cases. - Power
cord
- The main power breaker (switch) is in any cut operation.
8. After the installation of the product, move the product horizontally and water / drain
(water-cooled only).
Make sure that the hose is properly seated in place.
Damage to the product caused by the use of the product may not be free of
charge.)
9. Unplug the power plug when not in use for a long period of time.
Remove the liquid material.
10. Never touch the power plug with wet hands.
11. Please wear rubber gloves for safety when cleaning the product and pay attention
to the blade.
Hopefully. Do not spray water outside the product.
12. Do not disassemble or modify the product. (The malfunction or accident occurred
when using the modified I will not be.)
13. Only the liquid that can be edible must be used for the material inlet,
Please do not use the sieve.
Precautions for Safe Use
Be sure to read it to make it safer to use it.
▪Safety guidelines
▪Precautions for safe use
▪Product specifications
▪Installation method
▪Markings (PCB)
▪How to use
▪Cleaning methods
▪Trouble
▪Product Warranty
2P
5-6P
7P
8P
9P
10-16P
17-19P
20P
21P
www.crechef.co.kr

Product Features
1. There is no changeable the quality Snow flake quality and
machine performance even continuous operation for a long
time.
2. You may select the exact quantity of snow flake for one
person and two persons.
- It can be controlled the production quantity of snow flake by
operating (touching) the buttons.
- It is easy to adjust the operating time so that production
quantity can be controlled.
3. Easy to replacing the storage containers for feedstock
- The snow-flake material can be stored in a storage jar and
then easily replaced by the nozzle (to be sold by nozzle set).
4. Adjusting the drum rotation speed.
- Depending on the type of Raw material, drum rotation speed
can be adjusted to make the best Snow flake.
5. Just touch the button and it stops right away, so you can use
the machine as much as conveniently.
6. Cleaning Function
The cleaning function allows the drum and interior of machine
to be cleaned by clean water after production is completed.
54
Precaution (for safe use)
√ The following instructions are intended to be used safely and
accurately to prevent unexpected risks or damage, so be sure to keep
them safe.
√ Safety-related precautions are divided into the following, depending on
the amount of risk and damage expected when misused and the
degree of urgency of risk generation:
Warning : Violation of instructions may result in serious injury or death.
Caution : In case a minor injury or damage to the product may occur if
the instructions are violated.
This symbol is intended to alert you to items that may pose a hazard and
to operate them.
This symbol is a protective symbol that must be followed.
※Caused failure or fire.
Do not spray products with insecticides
or flammable sprays.
※ Not only is it harmful to the human
body, but it can also cause
product failure or fire.
Do not unplug or move the power
plug during operation.
※ Caused failure or electric
shock.
※ This can cause
electric shock.
Do not spray water directly
on the product.
Do not plug or touch the power plug
with wet hands.
This picture symbol is a prohibited symbol.
www.crechef.co.kr

6
5
Do not bend the power line too hard
or break it under heavy weight.
Failure to remove
the power plug
may result in a fire
caused by an high
temp insulating fire.
Do not touch or manipulate the child.
Risk of electric
shock or injury.
This will cause
the fault to
occur.
Do not use in narrow areas, sloped or
bumpy floors, make sure to check the
level and install.
If strange sounds, smells, and smoke
occur in the product, immediately turn
off the main power and contact the
sales person or manufacturer.
Causes failure
and
deformation. This may
cause electric
shock or fire.
This may cause
a fire. If the
power cord line
breaks down, do
not replace it
and contact the
A/S center.
Turn off the power plug when you are
not using it for a long time.
Don't give the product a hard on the
product.
Caution for safe use
Be sure to plug into a dedicated
110V or 220V outlet. Never disassemble, repair or
remodel arbitrarily.
Contact the
manufacturer or
salesperson if you
need to repair the
problem as it may
break down, shock or
fire.
Do not touch the inside of the product
with hands or rubber gloves, especially
the Snow flake making drum and blade
parts.
This cause
the injury.
This may
cause electric
shock or fire.
Do not climb on top of the product,
put heavy things up or stack them. Keep away from heat devices &
tools.
Causes failure
and
deformation.
Causes
distortion,
discoloration,
and fire.
Do not pull out the power cord.
Caution for safe use
Warning
www.crechef.co.kr
Caution

7 8
Name Chefsnow –Snow flake ice machine
Model CRE-170A / CRE-170W
Power AC110 V / 220V / 50 Hz / 60Hz, 1 Ph
Consumption 0.8 Kw
Amps 4 A
Refrigerant R-404A
Size 540mm*350mm*600mm
N/WT 46KG
Capacity 170Kg / day
Cooling Type Air cooling (A) / Water cooling (W)
Installation Method
* The body is installed in a place with a strong, level floor.
More than 10cm
from the wall More than 10cm
from the wall
Remove the power plug and remove the water from the water pan
when moving the main body or not in use for a long time.
* Install the product on a flat surface.
Sloped areas can vibrate the product.
* Open the front door and wipe the inside of the ice chamber with a soft,
dry cloth before starting the product.
* Check that the power plug or cord is not damaged and
that the voltage is 110 V or 220V and 50/60Hz
before connecting the power plug (to prevent electric shock).
* Use an outlet with an electrical capacity of 20A or more.
* Be sure to connect to an outlet with an earth terminal.
* Do not mix multiple devices in a single outlet or use an extension cord.
* Always install at least 20Cm away from the wall to avoid product draft.
Specification
Left Right
Upper Rear (Air Cooled)
Front
www.crechef.co.kr
Rear (Water Cooled)

9 10
Display part (PCB)
Model : CRE-170A
How to use CRE-170A
2. Turn the switch on the power breaker
in the upper left corner of the product.
3. Press the power button to turn on the power
(the screen will show ‘Chefsnow')
1. Switch on the power plug in a 110V or 220V power outlet.
4. Put a ice-cream milk pan in the ice chamber and fix it.
5. Pour the frozen water ingredients (water purified, milk) into
the top storage container. (Maximum capacity 2 liters)
* Power on :
If you press POWER SW for more than 1 seconds, it'll turn on with the
beep sound. After 3 seconds, you'll see the logo screen and a screen
of 1 bowl for one person screen.
* Power Off :
Press POWER SW for more than 1 second and turn it off with beep
sound. (If you turn off the power, the raw material valve will open and
then turn off.)
www.crechef.co.kr

11 12
How to use (CRE-170A)
Logo
(Chefsnow)
* Logo screen 3 seconds later waiting for
one person menu
* Press the START/STOP key to display and
operate as shown below.
1 BOWL
120 SEC
RUN
SP 07
START
CLEANING
3 MIN
SP 07
* When the START/STOP key
is pressed during operation,
it is displayed and stopped as shown below.
*CLEANING : 1~10min.
1 BOWL
120 SEC
WAIT
SP 07
FINISH
www.crechef.co.kr
How to use (CRE-170A)

13 14
How to use (CRE-170A)
How to use (CRE-170A)
* For one person : 10~999SEC
* Insufficient materials will be marked LOW
and the valve will open.
1 BOWL
120 SEC
LOW
SP 07
Raw material
supply
1 bowl
* If the material is not supplied for
more than 1 minute after LOW is marked,
the EMPTY indicator will be displayed before it ends.
* For 2 persons : 10~999SEC
1 BOWL
120 SEC
EMPTY
SP 07
1 BOWL
120 SEC
READY
SP 07
2bowl
2 BOWL
120 SEC
READY
SP 07
No raw
material
www.crechef.co.kr

11 12
*Continuous : 30 minutes to 8 hours setting
*Comp Protection Switch, when it is activated,
the COMP ERR is displayed before
it stops working.
1 BOWL
120 SEC
COMP ERR
SP 07
COMP ERROR
Continue
*Press the UP/DN key during operation
to change the motor SPEED.
*Warm-up : 30~240SEC
1 BOWL
120 SEC
RUN
SP 09
CONTINUE
30MIN
READY
SP 07
Warming Up
WARMING UP
120 SEC
SP 07
Speed control
www.crechef.co.kr
How to use (CRE-170A) How to use (CRE-170A)

15 16
* Drum speed : 01~15 levels
* CHILD LOCK: START/STOP
Press the key for more than 2 seconds
to lock it. (ST/STOP only)
1 BOWL
120 SEC
RUN
SP 09
Speed control
SPEED
DRUM SPEED
RUMTIME : 99999H
SP 07
You can change the setting by
pressing SET key for more than
2 seconds for each menu.
Press UP/DN key to change the
setting.
* Change settings
www.crechef.co.kr
How to use (CRE-170A) How to use (CRE-170A)

17
18
How to clean
2. Remove the milk cart from the freezer and then turn the milk cart on the bottom
of the water pan to detach it. Remove any water/milk remaining in the separated
milk cart, clean it with a neutral detergent, and dry it.
3. Remove the milk cart from the freezer and then turn the milk cart
on the bottom of the water pan to detach it.
Remove any water/milk remaining in the separated milk cart,
clean it with a neutral detergent, and dry it.
4. Press the cleaning button to send the remaining ingredients in the milk bin.
5. Apply a mild sponge with a mild detergent and wipe it lightly. Spray water with a
cleaning nozzle to rinse cleanly.
6. Clean the main entrance with a cleaning brush.
(If you press the CLEAN button, the inlet will close after one minute. Do not let the
brush blossom for a long time.)
7. When the blade is not rotating, place your hands inside the ice chamber and wipe
off the left and right sides.
- Since the drum is rotating, special care must be taken not to allow the hand /
spongy to get caught in the blade.- (There is a risk of injury.)
8. The milk cart on the back of the ice chamber must be located as shown in the
picture below.
Cleaning
CLEANING
3 MIN
SP 07
* CLEANING : 1 ~10 min.
www.crechef.co.kr
How to clean

19 20
1.The Snowflake storage under the drum must be cleaned every day. When
cleaning the Snowflake chamber, use a neutral detergent to clean it, and
finish with steam and sterilization.
2. When cleaning the exterior, be careful not to come into contact with the
power break at the top left and the rear upper main PCB (risk of short
circuit and electric shock).
3. When the product is shut down after production, turn off the power button
and the breaker switch, remove the ice sheet from the ice chamber, and
keep it dry. Keep clean and dry at all times to prevent bacteria, fungi, and
viruses from inhabiting.
4. If the unit is not used for an extended period of time, turn off the power
switch and prevent the main water supply.
5. The repair and repair of the machine must be performed only by persons
who have been trained in maintenance and by authorized supplies.
If any issues arise during the operation and repair of the product by
persons who are not familiar with the use of the product on their own
account, all repair costs, including legal liability, will be borne by the
consumer, even during the warranty period.
Snow Flake Storage and Exterior Cleaning
www.crechef.co.kr
How to clean

Trouble shooting / Out of order ? What should I do in this case?
Symptom Checkpoint Action
When the Cooling
Compressor rattles and
stops.
Cooling
Is there a loud noise and cooling compressor stops
jerking? (subject to Water
-cooled type only)
Please increase the
quantity of supplying Cooling Water in
case of Water Cooling
Snowflake powder is not good
ice
quality ?
Have you checked the sugar content of the ice
water?
. Did you check the drum speed?
Did you check the Temperature of Drum ?
The higher sugar content of the ICE, the lower the drum
rotation speed required.
.
If the drum temperature is not cold,
refrigerant gas may not be available.
The water in the water gutter
(table) overflows.
Is the water supply valve too much open?
Does the level sensor work?
Is the product tilted?
Slightly lock the water supply valve
Please check the Water level sensor
.
Use the product on a flat surface.
Water supply is not properly
working
When the water is supplied, Is the LOW light which is
among of 3 circles light on the touch panel on or off
repeated?
The Water level sensor is too low.
(Please call the call center)
Display is dimmed.
.
Please turn them off in order.
Touch Panel -> Product Power Breaker -> Plug-out
It does not
work.
Did you check the side main power switch?
Whether Power plug securely plugged into the
outlet? .
Is it bad for Power outlet ?
Is not it blackout ?
Check if the main switch is ON.
Plug in the power plug and operate it. .
Try use another power outlet
Make sure the electricity is on and try again.
When the ICE (Snow) Flakes
are not coming out
Water is not properly supplying?
Milk is not properly supplying
Make sure the milk container contains milk. .
Make sure the milk pan is securely fastened.
Even there is water in the container, and there is no water in
the water Storage (reservoir), please call to Crechef.
www.crechef.co.kr