VEVOR SKF-S25J User manual

INSTRUCTION MANUAL
SKF-S25J
READ ALL INSTRUCTIONS BEFORE USING
（This is the original instruction, please read all manual instructions carefully
before operating. VEVOR reserves clear interpretation of our user manual. The
appearance of the product shall be subject to the product you received. Please
forgive us that we won't inform you again if there is any technology or software
updates on our product.）

IMPORTANT SAFETY INFORMATION：
WARNING：Read all safety warnings, instructions, illustrations and specifications provided
with this electric appliance. Failure to follow all instructions listed below may result in electric shock, fire
and/or serious injury.
Save all warnings and instructions for future reference.
SAFETY INFORMATION
This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and the word “WARNING” or “CAUTION”. These words are
defined as:
Indicates a hazardous situation which, if not avoided, could result in death or serious injury.
Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
ICE CAN’T BE STORED IN THE ICE BIN DURING NIGHT TIME, IT’S
NOT FRIDGE, ICE WILL BE MELTED INTO WATER AND FLOW OUT OF THE MACHINE.
To reduce the risk of fire, explosion, electric shock, exposure to UV radiation, or injury when using
your ice maker, follow these basic safety precautions:
●This product must be properly installed and located in accordance with the Installation instructions before it is used.
●When using electrical appliances,basic safety precautions should be followed to reduce the risk of fire,electric shock
and injury to persons or property. Read all instructions before using any appliance.
●High humidity environment will increase the risk of short circuit or electric shock. If in doubt, please cut off the power
supply of the ice maker.
●Do not exceed power outlet ratings. It is recommended that the ice maker is connected to its own circuit. Use only
standard electrical supply that is properly grounded in accordance with the National Electric Code and local codes and
ordinances.
●If the ice maker is brought indoors from outdoors during the wintertime,give it a few hours to warm up to room
temperature before plugging to power source.
●Do not store explosives, such as combustion-supporting sprays in the appliance.
●The machine is intended to be used in household and similar applications such as:
-kitchen areas in shops,offices and other working environments;

-farm houses
-by clients in hotels,motels and other residential type environments;
-Catering industry and similar non-retail industry.
●This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by children without supervision.
●Avoid direct sunlight and make sure that The machine should be used in the household and without obstacles
surrounded, good ventilation place.There is must be 50cm at least between the four sides of the machine with the wall.
●Do not tip the machine over.
●We do not recommend the use of an extension cord,as it may overheat and become a risk of fire.
●Don’t use any liquid other than water in the unit to make the ice.
●Do not store or use flammable vapors or liquids near this product.
● Do not allow children to climb, stand or hang on the ice maker. They could seriously injure themselves.
● Do not use with water that is microbiologically unsafe or of unknown quality.
● To avoid risk of injury, place power cord in such a way it cannot be pulled on by children or cause a tripping hazard.
● Place power cord in such a way that it is not in contact with hot surfaces.
● Do not operate if any component, including the cord or plug, is damaged.
● Unplug the product before cleaning or repairing, and when not in use. (Note: If the machine needs repair, it is strongly
recommended that it be operated by professionals. Type Y attachment: If the supply cord is damaged, it must be replaced
by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.)
● Do not immerse any part of the product in water.
● Do not plug or unplug product with wet hands.
● Do not place the power cord on carpet or other heat sources
● Do not attempt to disassemble, repair, modify, or replace any part of your product.
● Use this product only for its intended purpose as described in this user manual.
● If the power cord is damaged, it must be replaced by the manufacturer or similar professionals in order to avoid
danger.
● Do not use any accessories not recommended by the manufacturer.
● The foaming materials inside is combustible which must be kept away from fire.
● It’s forbidden to pull the cable to unplug the plug,pull the plug is a must.
● Except for the method recommended by the manufacturer, no mechanical tools or other methods shall be used to
accelerate the defrosting process. Do not damage the refrigeration circuit.
●There are high-pressure, flammable and explosive refrigerants in the compressor. Do not damage the refrigeration
system. Care or repair should be carried out by professionals. Be especially careful when installing and transporting.
●There are heat insulation materials in the ice maker, which are combustible materials, and must be kept away from fire
sources. Repairs must be carried out by the manufacturer or professionals. Scrap must be disposed of by the designated
recycling department.

Product specifications:
Model No
SKF-S25J
Rated Voltage
AC120V 60Hz
Input Power
350W
Rated Current
3A
Ice production
62lbs/day
Ice basket capacity
5lbs
Refrigerating
R290/24g
Shock Protection Type
I
Foam Material
Cyclopentane
Quick introduction：

Installation and setup
Caution: Installation must be installed by professionals.

Warning:
The drain of inner tank must be always connected to a floor drain.
The drain of internal water tank (Only connect to a floor drain after cleaning, or it must be plugged)
Installation requirements
Product is designed to be installed indoors. Do not use your ice maker outdoors.
■ Product must be installed upright on a flat, level surface that is able to support the total weight when full of water.
■ Ensure a minimum of 50cm clearance around the side and back walls of the ice maker for proper air circulation.
■ Install the product in a well-ventilated area with an ambient temperature between 3℃ and 40℃.
■ Do not place the product near heat sources such as ovens or cook tops.
■ Do not place the product in direct sunlight or rain.
■ Do not place any stuff on the top of the machine.
Lifting Hazard: It is recommended to have two people move and install the
ice maker in order to prevent injury.

Prepare for use
1. Carefully remove packing material. Do not use sharp tools that can damage the ice maker.
2. Ensure all components are present.
(An assembled filter, 1 drainage pipe and 2 silica plug, drip tray and drip tray cover are a standard on the
machine.)

3. Place the ice maker upright on a flat, level surface and plug it in.
4. Clean the ice maker before first use.
Connect to water and drain pipe
It must be connected connected to tap water. If there is a problem caused by the tap water without a filter, our company
will not bear the cost of repairing.
(1) Use tap water as water source
The filter you received is assembled, plug the water intake pipe firmly into the connector at the back of
the machine until you can’t insert it anymore, and the other side connects to the water tap.
(2) Drain
The drain of the inner tank must be always hooked it up to a floor drain or a container, or the water will leak to floor !
The drain of internal water tank only connect to a floor drain after cleaning, or it must be plugged.
Understanding the display
1. Please make sure：
1.The tap is on or there is water in the bottle.
2.The drain pipe was inserted into sink or bucket
3.The machine is power on.
2. Touch screen:
The water supply pressure should be 0.1-0.4MPa; if the pressure is greater than 0.4MPa,
a pressure reducing valve is required.

Control board
（1）Standby: Plug the power cord into the socket will make the machine enter standby mode.
（2）Touch “making ice”,”dispense ice”,”clean” icon under standby mode, the selected indicator will blink.
（3）Making ice: Touch “Making ice” icon under standby mode or “clean” mode to make the machine start to make ice;
Long touch this icon for 2 seconds during “Making ice” mode to make the machine enter standby mode.
(4)Dispense ice: Touch this icon under standby or “making ice” mode will make the machine to dispense ice, touch
again to stop dispensing. If no ice is dispensed within 30s,it will stop dispensing automatically. If the outlet is jammed,
long press this icon for 5s,ice cubes will be dispensed automatically after 25s.
(5 ) Large / Clean: Touch this icon during “making ice” mode will make the machine to dispense ice continuously for
5min, touch again will make the machine stop dispensing ahead of time.
Long touch the icon for 3s under standby mode to start the self-cleaning progress, touch again to stop the self-cleaning
progress. After cleaning, unplug the outlet to drain. Make sure the drain pipe is connected before starting the machine.
NOTE:1. Clean mode and ice making mode can’t be operated at the same time.
2. The two outlets of the machine must be hook up to a floor drain after cleaning.Observe the water flow to avoid
overflow.
3. After that, the outlet of the internal water tank must be plugged.
(1) Ice full ：As infrared rays detected no ice fall over 2 min, the machine will stop and the “ice full” indicator will be
on, the machine will restart to work as you take some ice out or after the ice melt.
(2) Fault: If no ice fall over 15min for the first cycle, the machine will stop and FAULT indicator will be on. After that,
if there is no ice fall over 3min, the machine will stop working and the FAULT indicator will be on.
Warning: The ice machine is used to make and store ice,wash your hands before taking ice.
Clean and care
1. For long time storage
a) Power off the machine and pull the plug.
b) Turn off the faucet and remove the inlet pipe
c) Take out all the ice,drain the water inside
d) Dry the ice bin and interior.

2. Daily cleaning
During the working time, more and more scales will precipitate in the water tank. If it is not cleaned in time, it will cause
malfunctions. Generally, it needs to be cleaned once a week. Take all nugget ice out, add 10% edible citric acid to the
water tank during cleaning, touch the clean icon, it will take about 5min to finish the clean procedure, and then
repeatedly rinse with fresh water before using. Observe the water flow at any time during the cleaning mode to avoid
overflow, if the water is too swift which lead to overflow, turn down the tap.
3. Clean interior
NOTE: Pull the plug before cleaning or maintaining
To make the machine work normally, check and clean condenser annually.
Don’t use alcohol to clean the in-wall of the machine,it will break the plastic materials.
4. Clean exterior
Clean the exterior with detergent weekly
Common malfunction analysis
Issues
Check items
Possible causes
Solutions
The machine
doesn’t work
Power cord
The plug didn’t plug into socket
Plug into socket
The fuse of PCB
The fuse is broken
Replace the fuse
PCB
Broken
Replace the PCB
Ice full
Ice full
Take out some ice
Proximity switch
Proximity switch is broken
Replace the proximity switch
Power supply
No power or lower voltage
Contact power supply bureau
Water supply
No water or water pressure is low
Check water source and its
pressure
Inlet valve
Inlet valve is broken
Replace the inlet valve
Compressor didn’t
work or stop
working suddenly
Power supply
No power or lower voltage
Contact power supply bureau
Air inlet is congested
Ensure that the machine’s
surrounding space of at least 50
cm of clear of any objects
Air inlet is congested
Condenser
Too much dust covered
Clean the condenser
Refrigerant
Refrigerant leaked
Contact after sales service
compressor
Connection wire is broken off
Contact after sales service
No water in the
water tank
Water supply
No water or water pressure is low
Check water source and its
pressure
Inlet valve
Inlet valve is broken
Replace the inlet valve
Water leakage
Water inlet
Water inlet is loosened
Re-tightened the water pipe
Drain pipe
Didn’t connect to drain pipe or sewer
Connect to drain pipe or sewer
Float
Jammed or broken
Adjust or replace
Stoppage indicator is
on
No ice during 15min
Refrigeration system
Contact after sales service
There are ice fall into the
ice basket
Infrared ray is broken
Contact after sales service

RoHS
Take too long to
make ice
Water pressure
Lower water pressure
Check the water source
Water
temperature
Water temperature is high
Change to a water source of lower
temperature
Ambient
temperature
Ambient temperature is too
high or too low
Change to a place of lower temperature
Refrigerant
Refrigerant leakage
Contact the after sales
Productions of
ice cubes is low
and the cube ice
is too thin
Condenser
Too much dust covered
causes bad ventilation,,will
take too long to make ice
Clean the condenser
Water pump
Water pump broken
Replace a water pump
Ambient
temperature
Ambient temperature is
relative high
Change to a place of lower temperature
Air inlet
Air inlet is congested
Ensure that the machine’s surrounding
space of at least 50cm is clear of any
objects
Add water
indicator is on
Water tank
No water inside
Check the water supply
Water in the tank
Check the float
Noise
Condenser
The sound of the fan
scrapes against condenser
Contact the after sales
Valve
It worked too long for
single time
Restart the machine after the solenoid
valve cool off
Evaporator
In the beginning of making
ice
Normal
Nugget ice maker
Category
Accessories
Harmful substance
Pb
Hg
Cd
Cr(VI)
PBB
PBDE
Hardware
Refrigeration
Component
○
○
○
○
○
○
Screws
○
○
○
○
○
○
Sheet metal
○
○
○
○
○
○
Electricity
Fan component
○
○
○
○
○
○
Power cord
○
○
○
○
○
○
PCB
×
×
×
○
○
○
Compressor
○
○
○
○
○
○

Component
component
Plastic
injection
Plastic panels
○
○
○
○
×
×
Water tank
○
○
○
○
○
○
Inner shaft
○
○
○
○
○
○
Feet
○
○
○
○
○
○
Ties
○
○
○
○
○
○
Silicon gel
plugs
○
○
○
○
○
○
Wrapping
Carton
○
○
○
○
○
○
Foam
○
○
○
○
○
○
PE bag
○
○
○
○
○
○
Labels
○
○
○
○
○
○
Manual
○
○
○
○
○
○
E-mail：[e-mail]
Manufacturer: Cixi Jirui Electric Appliance Co.,Ltd
Add: 118# Nanxin Road,Zonghan Street,Cixi City,Zhejiang Province