CHERUBINI MAGO User manual

MAGO
ISTRUZIONI - INSTRUCTIONS - EINSTELLANLEITUNGEN
INSTRUCTIONS - INSTRUCCIONES
La Domotica Bluetooth
Bluetooth Domotics
Bluetooth-Domotik
La domotique Bluetooth
La Domótica Bluetooth

3
DISPOSIZIONE IMPIANTO IN APPARTAMENTO
SYSTEM LAYOUT IN THE APARTMENT
ANORDNUNG DES SYSTEMS IN DER WOHNUNG
POSITIONNEMENT DE L’INSTALLATION DANS L’APPARTEMENT
DISPOSICIÓN DE LA INSTALACIÓN EN UN APARTAMENTO
La distanza massima tra i vari dispositivi non deve superare 8 metri.
The maximum distance from one device to the next should not exceed 8 metres.
Der Abstand zwischen den einzelnen Geräten darf nicht mehr als 8 m betragen.
La distance maximale entre les différents dispositifs ne doit pas excéder 8 mètres.
La distancia máxima entre los distintos dispositivos no debe ser superior a 8 metros.
max 8 m
max 8 m
max 8 m

TRANSLATION OF THE ORIGINAL INSTRUCTIONS
Table of contents:
MAGO DEVICES AND ELECTRICAL CONNECTIONS
Introduction .......................................................................................................... p. 24
MAGO Switch A510046 ........................................................................................ p. 25
MAGO Control unit A510051 for standard wiring motor ...................................... p. 26
MAGO Control unit A510051 for RX white wire motor ......................................... p. 27
MAGO Actuator A510048 ON/OFF for two independent loads ............................. p. 28
MAGO Actuator A510048 thermostat ................................................................... p. 29
MAGO Dimmer A510047 ...................................................................................... p. 30
MAGO Gateway A510049 ..................................................................................... p. 31
APP INSTALLATION
Installing the MAGO application .......................................................................... p. 32
SYSTEM CREATION
MAGO system creation ........................................................................................ p. 33
Device association ............................................................................................... p. 34
Device identication ............................................................................................ p. 34
App-assisted identication ................................................................................... p. 34
Description of the main screen ............................................................................. p. 35
SYSTEM CONFIGURATION
MAGO system conguration ................................................................................. p. 36
MAGO Switch and MAGO Control Unit advanced settings menu ......................... p. 37
MAGO Actuator advanced settings menu ............................................................. p. 38
How to connect MAGO Gateway to the Cloud ...................................................... p. 39
How to remove a MAGO item from the system ..................................................... p. 39
How to add a MAGO item to the existing system ................................................. p. 39
Main menu ............................................................................................................ p. 40
Adding a smartphone to an existing system .......................................................... p. 40
MAGO devices reset .............................................................................................. p. 41
Technical features .................................................................................................. p. 42
Conformity ............................................................................................................ p. 103
23
ENGLISH

25
MAGO DEVICES AND
ELECTRICAL CONNECTIONS
APP INSTALLATION
INTRODUCTION
MAGO DEVICES:
Device Positioning Specialisation CH motor
compatibility
MAGO Switch Wall-mounted with
built-in box
Shutter, Awning, Screen,
Venetian blind
Standard wiring
MAGO
Control unit
Flush-mounted Shutter, Awning, Screen,
Venetian blind, Adjustable
roller shutter
Standard wiring
Wiring with white
lead
MAGO
Actuator
Flush-mounted 2 stable independent outputs
2 independent impulsive
outputs
2 independent timed outputs
1 switching output (diverter)
1 switching thermostat
output
MAGO
Gateway
Tabletop Cloud access
Temperature and humidity
sensors
MAGO
Dimmer
Flush-mounted 2 independent LED outputs
MAGO is a system consisting of various devices connected to each other via Bluetooth
in a mesh network. The system can be expanded adding other devices at any time; this
allows considerable distances to be covered - even across different oors. The system
is only accessible via the MAGO application downloaded to a smartphone. The data
exchanged on the system are encrypted and can only be accessed from MAGO devices
using the system password, or from smartphones with access authorisation. This makes
of MAGO a highly secure system protected from unauthorised access.
Maximum system capacity:
192 devices, 15 units, 16 scenes, 16 environments, 250 events.
24
ENGLISH

SYSTEM
CREATION
SYSTEM
CONFIGURATION
25
MAGO Switch A510046
L1 N
C
M
Wall-mounted button panel for standard wiring motors.
APP INSTALLATION
MAGO DEVICES:
Device Positioning Specialisation CH motor
compatibility
MAGO Switch Wall-mounted with
built-in box
Shutter, Awning, Screen,
Venetian blind
Standard wiring
MAGO
Control unit
Flush-mounted Shutter, Awning, Screen,
Venetian blind, Adjustable
roller shutter
Standard wiring
Wiring with white
lead
MAGO
Actuator
Flush-mounted 2 stable independent outputs
2 independent impulsive
outputs
2 independent timed outputs
1 switching output (diverter)
1 switching thermostat
output
MAGO
Gateway
Tabletop Cloud access
Temperature and humidity
sensors
MAGO
Dimmer
Flush-mounted 2 independent LED outputs
24
ENGLISH

27
MAGO Control unit A510051
Flush-mounted control unit for standard wiring motor
26
L1 N
M
C
L1 N
optional
control
ENGLISH
MAGO DEVICES AND
ELECTRICAL CONNECTIONS
APP INSTALLATION

MAGO Control unit A510051
Flush-mounted control unit for RX white wire motor
27
L1 N
L1 N
optional
control
L1 N
L1 N
M
MAGO Control unit A510051
Flush-mounted control unit for standard wiring motor
26
optional
control
ENGLISH
SYSTEM
CREATION
SYSTEM
CONFIGURATION
APP INSTALLATION

2928
MAGO Actuator A510048
ON/OFF actuator for two independent loads.
L1 N
optional
control
L1
U1
U2
optional control
U1 U2
1 ON ON
2 OFF ON
3 ON OFF
4 OFF OFF
ENGLISH
MAGO DEVICES AND
ELECTRICAL CONNECTIONS
APP INSTALLATION

29
MAGO Actuator A510048
Thermostat actuator.
THERMOSTAT INPUT
BOILER/AIR CONDITIONER
CONTACT NO
28
optional
control
optional control
U1 U2
1 ON ON
2 OFF ON
3 ON OFF
4 OFF OFF
ENGLISH
SYSTEM
CREATION
SYSTEM
CONFIGURATION
APP INSTALLATION

31
MAGO Gateway’s two main features are:
1) Connection to the Cloud, i.e. ability to remotely access the Mago system via Wi-Fi or a
GPRS connection.
2) Through the temperature and humidity sensors integrated in the device, MAGO
Gateway allows these values to be displayed on the application home page.
Temperature data can also be used by the specialised thermostat MAGO Actuator, to
manage the activation or deactivation of the boiler or air conditioner.
MAGO Gateway is an optional unit: the system will work even without this device.
Front LED description:
Steady red: it indicates that the Cloud conguration is not complete or has not been
implemented.
Slow green: it indicates that the connection to the network has not yet been made, or
that logging in to the GPRS network has not occurred.
Fast green: it indicates that logging in to the network has been successfully performed,
or that IP connection from the GPRS network has been obtained.
Steady green: it indicates that the gateway is connected with the server.
Steady green + ashing red: it indicates that the gateway is temporarily unavailable
because updating is in progress.
Blue: it indicates the reception of a Bluetooth package.
MAGO Dimmer A510047
Low voltage device to control 2 LED bars.
30
optional
control
12/24 V DC
STRIP LED 1
STRIP LED 2
+
+
+
ENGLISH
MAGO DEVICES AND
ELECTRICAL CONNECTIONS
APP INSTALLATION

31
MAGO Gateway A510049
Temperature/humidity sensor and internet gateway.
MAGO Gateway’s two main features are:
1) Connection to the Cloud, i.e. ability to remotely access the Mago system via Wi-Fi or a
GPRS connection.
2) Through the temperature and humidity sensors integrated in the device, MAGO
Gateway allows these values to be displayed on the application home page.
Temperature data can also be used by the specialised thermostat MAGO Actuator, to
manage the activation or deactivation of the boiler or air conditioner.
MAGO Gateway is an optional unit: the system will work even without this device.
Front LED description:
Steady red: it indicates that the Cloud conguration is not complete or has not been
implemented.
Slow green: it indicates that the connection to the network has not yet been made, or
that logging in to the GPRS network has not occurred.
Fast green: it indicates that logging in to the network has been successfully performed,
or that IP connection from the GPRS network has been obtained.
Steady green: it indicates that the gateway is connected with the server.
Steady green + ashing red: it indicates that the gateway is temporarily unavailable
because updating is in progress.
Blue: it indicates the reception of a Bluetooth package.
LED
MULTIFUNCTION
BUTTON
30
ENGLISH
SYSTEM
CREATION
SYSTEM
CONFIGURATION
APP INSTALLATION

33
Installing the MAGO application
32
APP MAGO
ENGLISH
MAGO DEVICES AND
ELECTRICAL CONNECTIONS
APP INSTALLATION

MAGO system creation
33
At this point, after connecting all the devices and installing the MAGO application, we
can create the system by associating the various components to the Bluetooth system.
1) Open the app, click on“+”, then “create new system”.
2) Assign a name to the system.
3) Enter the 8-digit system identication code (store this code safely).
ID Code: __________________________
4) Enter the 6-digit administrator password. The administrator is the highest user
prole with the most power over the system. Lower prole passwords are created
automatically and can be changed by the administrator.
User Password New
password
Powers
Congu-
ration Planning Use
Administrator YES YES YES
Expert NO YES YES
Base NO NO YES
User 1/2/3 NO NO YES
For user and password management, refer to “MAIN MENU” on page 40.
32
ENGLISH
SYSTEM
CREATION
SYSTEM
CONFIGURATION
APP INSTALLATION

35
System name
Main menu
Temperatura
Installed
devices
Once it has been exactly identied, select the device from the list.
1) Enter the name of the controlled item that we are controlling (for example: “Kitchen
shutter”).
2) Select the most appropriate application from the list (awning, roller shutter, etc.).
3) Place the item inside a room. You can rename existing rooms or create others.
4) Repeat these steps for all the devices to be added to the system.
34
Device association:
After clicking on “Add device”, the app shows a list of all the available devices that can
be added to the system. Be careful in this phase because devices from the next-door
apartment may also be on the list. To avoid errors, it is possible to accurately identify the
device that we are adding in two different ways.
Device identication:
Press and hold down for 5 seconds the Mago switch stop button (Fig. 1) or the middle of
the other devices (Fig. 2) until the LED ashes. On the app, the TEST button of the newly
identied device goes green for one minute (Fig. 3).
LED
App-assisted identication:
Reach the device to be identied. Press the TEST button on the app of the MAGO device
that you wish to identify, wait a few seconds, the motor or the connected lights should
be activated.
press
1 2
3
ENGLISH
MAGO DEVICES AND
ELECTRICAL CONNECTIONS
APP INSTALLATION
LED
STOP

35
Description of the main screen
System name
Main menu
Temperatura
Installed
devices
Home page Rooms
Groups
Scenarios
List of
devices
Humidity
*Connection
state
*Multifunction
button
Favourites Planning
*CONNECTION STATE *MULTIFUNCTION BUTTON
White
System synchronised
Not connected to the system
Bluetooth connected
Cloud connected
Cloud connection in progress
Yellow
Synchronising in progress
Red
Not synchronised
34
ENGLISH
SYSTEM
CREATION
SYSTEM
CONFIGURATION
APP INSTALLATION

3736
MAGO system conguration
MULTIFUNCTION BUTTON
With the multi-function button you
can access the advanced conguration
menu:
1) Select the desired item (for
example “Bathroom shutter”)
2) With the multifunction button
select “Change”
3) Select “Advanced”
IMPORTANT
- For the MAGO switch and Mago control unit devices it is essential to set the raising
and lowering times, measuring their actual duration in seconds. See the “raising and
lowering times” parameters in the advanced settings menu.
- For the thermostat MAGO Actuator, it is essential to select the Mago Gateway module
used as a temperature/humidity sensor. See the “Temperature sensor” parameter in the
advanced settings menu.
ENGLISH
MAGO DEVICES AND
ELECTRICAL CONNECTIONS
APP INSTALLATION

MAGO Switch and MAGO Control Unit advanced settings menu
37
Parameter Options Description
Motor type Standard (default) For motors with a mechanical/electronic
limit switch with standard connection
(brown, black, blue).The outputs will
remain active throughout the travel (up/
down travel time).
Pulses For motors with white wire control. The
outputs are managed by pulses.
Motor for adjustable
shutter with
connector
No (default) Mode 5
Yes Mode 4
Venetian blind
control mode
CH Cherubini (default) Short pulse <1 sec: Impulsive
Long pulse >1 sec: Continuous motion
EU European Short pulse <2 sec: Impulsive
Long pulse >2 sec: Continuous motion
US United States Short pulse >0,5 sec: Impulsive
Long pulse <0,5 sec: Continuous motion
Specialisation Rolling shutter The specialisation is indicated during the
creation of the system and can be changed
from this menu.
Awning
Screen
Venetian blind
Orientable shutter
Upward travel
time
0-240 seconds
(default 30)
Output activation time during the
motor raising movement
Downward travel
time
0-240 seconds
(default 30)
Output activation time during the
motor lowering movement
Position adjustment
time
10-100 tenths of a
second (default 10)
Total slat tilting time
Preferred position 1 0-100%
(default 25%)
Preferred intermediate position 1
Preferred position 2 0-100%
(default 75%)
Preferred intermediate position 2
36
ENGLISH
SYSTEM
CREATION
SYSTEM
CONFIGURATION
APP INSTALLATION

39
1) From the main page select the MAGO Gateway device
2) With the multifunction button select “Change”
3) Select “Settings” and choose the connection mode
Off: Not connected (default)
Wi- Fi: Enter the name of the Wi-Fi* network and Password to access the network
SIM (GPRS): Insert the SIM in the slot under the device and the corresponding
parameters: APN and PIN.
*MAGO Gateway is only compatible with 2.4 GHz password protected Wi-Fi networks
(wpa/wpa2).
1) Go to the system
2) From the main page select the item that you wish to remove
3) With the multifunction button select “Change”
4) With the multifunction button select “Remove”
After this operation the selected MAGO item will become visible again and available to
be integrated in another system.
1) From the main page, select the word CHERUBINI to display the main menu
2) From the main menu select “Add device”
3) From the list of available devices select the desired one and proceed as described in the
paragraph “Device association”.
38
MAGO Actuator advanced settings menu
Parameter Options Description
Specialisation 2 independent stable
outputs (default)
Select the specialisation suitable for the type
of electrical connection required.
1 combined exchange
output
2 independent
impulsive outputs
2 independent timed
outputs
Thermostat
Output 1 timer 8-10 hours
(default 10 seconds)
Output 1 activation time in “2 independent
timed outputs” mode.
Output 2 timer 8-10 hours
(default 10 seconds)
Output 2 activation time in “2 independent
timed outputs” mode.
Temperature
sensor
Select the MAGO
Gateway device
to be used as a
temperature/humidity
sensor
In the “Thermostat” mode it is necessary
to specify the MAGO Gateway device to be
used as a temperature/humidity sensor. This
operation is mandatory even if only one
MAGO Gateway is installed.
ENGLISH
MAGO DEVICES AND
ELECTRICAL CONNECTIONS
APP INSTALLATION

How to connect MAGO Gateway to the Cloud
How to remove a MAGO item from the system
How to add a MAGO item to the existing system
39
MULTIFUNCTION
BUTTON
1) From the main page select the MAGO Gateway device
2) With the multifunction button select “Change”
3) Select “Settings” and choose the connection mode
Off: Not connected (default)
Wi- Fi: Enter the name of the Wi-Fi* network and Password to access the network
SIM (GPRS): Insert the SIM in the slot under the device and the corresponding
parameters: APN and PIN.
*MAGO Gateway is only compatible with 2.4 GHz password protected Wi-Fi networks
(wpa/wpa2).
1) Go to the system
2) From the main page select the item that you wish to remove
3) With the multifunction button select “Change”
4) With the multifunction button select “Remove”
After this operation the selected MAGO item will become visible again and available to
be integrated in another system.
1) From the main page, select the word CHERUBINI to display the main menu
2) From the main menu select “Add device”
3) From the list of available devices select the desired one and proceed as described in the
paragraph “Device association”.
MAIN
MENU
38
Parameter Options Description
Specialisation 2 independent stable
outputs (default)
Select the specialisation suitable for the type
of electrical connection required.
1 combined exchange
output
2 independent
impulsive outputs
2 independent timed
outputs
Thermostat
Output 1 timer 8-10 hours
(default 10 seconds)
Output 1 activation time in “2 independent
timed outputs” mode.
Output 2 timer 8-10 hours
(default 10 seconds)
Output 2 activation time in “2 independent
timed outputs” mode.
Temperature
sensor
Select the MAGO
Gateway device
to be used as a
temperature/humidity
sensor
In the “Thermostat” mode it is necessary
to specify the MAGO Gateway device to be
used as a temperature/humidity sensor. This
operation is mandatory even if only one
MAGO Gateway is installed.
ENGLISH
SYSTEM
CREATION
SYSTEM
CONFIGURATION
APP INSTALLATION

4140
Main menu
Adding a smartphone to an existing system
Warning:
It is not possible to congure the system from two smartphone at the same time.
MAIN
MENU
From the main (Home) page select the word CHERUBINI to display the main menu. From
this menu you can add devices to the system, manage users, congure the cloud, change
language, etc.
1) Open the app, click on “+”, then “Connect an existing system”.
2) Assign a name to the system.
3) Enter the same 8-digit system identication code used before in the system creation
phase.
4) Enter the 6-digit password, given by the administrator user.
ENGLISH
MAGO DEVICES AND
ELECTRICAL CONNECTIONS
APP INSTALLATION