Chexx Automations K-2000A Installation and operation manual

1
K-2000A / K-2000AT Display User Manuals
Brief instruction
F1 Storage Mode (Set Transmitters number)
E1-Register Transmitters
E2-Register Remote Control
E3-Reigister Alarm Function Transmitters
E4-Register Cancel Function Transmitters
F2 Deletion Mode (Delete Transmitter Number)
E1-Delete Transmitters
E2-Delete Remote Control
E3-Delete Alarm Function Transmitters
E4-Delete Cancel Function Transmitters
F3 Display Setting
E1 Display Mode
E2 Storage Number
F4 Logout Setting (Remove Timing Setting)
F5 Cycle Mode
F6 Voice Setting
E1-Voice Mode
E2-The times of Voice Announcements
E3-Whether to read the number when cycling
E4-Volume Setting
E5-Brightness setting
E6-Operational sound navigation
E7-“Number”position
E8-To be developed
E9-Whether read Counter Number (Suit for queue call system)
F7 Keyboard Setting
E1 Partition Setting
F8 Key Settings
E1 Single-key or Multi-key Setting
E2 Voice pairing
F9 Restore Factory Settings
: Setting key, Confirm key, Move digit key
: Exit system
: Up key, Increase number key
: Down key, Decrease number key
F1 Storage Mode
E1 Register Transmitters
1. Press “ ” key 2 seconds, screen displays F1
2. Press “ ” key, screen displays E1
3. Press “ ” to confirm, screen displays 0001, “1”is flashing, and press “ ” “ ” “ ”
key to select the number you want save.
4. Press any key from transmitter, you will hear a voice (success), the number has been
registered successfully and then the number will skip to the next one,.
5. Press “ ” it will exit to “E1”, press “ ” again to exit setting state.
NOTE: If you hear a voice (failure), it means the number has been used.
Note: Press the number on the screen directly, number will cancel
E2 Register Remote Control
1. Press “ ” key 2 seconds, screen displays F1
2. Press “ ” key, screen displays E1, press to E2
3. Press “ ” to confirm, screen displays 0001, “1”is flashing and press “ ” “ ” “ ”
key to select the number you want to save.

2
4 Press any key from remote control, you will hear a voice (success), the number has been
registered successfully and then the number will skip to the next one
5. Press “ ” it will exit to “E2”, press “ ” again to exit setting state.
E3 RegisterAlarm Function Transmitters
1. Press “ ” key 2 seconds, screen displays F1
2. Press “ ” key, screen displays E1, press key two times to E3
3. Press “ ” to confirm, screen displays 0001, “1”is flashing, and press “ ” “ ” “ ”
key to select the number 0001-999.
4 Press any key from the alarm transmitter, you will hear a voice (success), the number has
been registered successfully and then the number will skip to the next one.
5. Press “ ” it will exit to “E3”, press “ ” again to exit setting state.
E4 Register Cancel Function Transmitters
1. Press “ ” key 2 seconds, screen displays F1
2. Press “ ” key, screen displays E1, press key to E4
3. Press “ ” to confirm, screen displays 0001, “1”is flashing, and press “ ” “ ” “ ”
key to select the number 0001-999.
4 Press any key from cancel transmitter, you will hear a voice (success), the number has
been registered successfully and then the number will skip to the next one.
5. Press “ ” it will exit to “E4”, press “ ” again to exit setting state
F2 Deletion Mode
E1 Delete Transmitters
1. Press “ ” key 2 seconds, screen displays F1
2. Press “ ” key to display F2, press “ ” to display E1
3. Press “ ” to confirm, screen displays 0001, “1”is flashing, and press “ ” “ ” “ ”
key to select the number you want delete.
4. Press “ ” key, you will hear a voice (success), means number has been deleted
successfully.
5. Press “ ” it will exit to “E1”, press “ ” again to exit setting state
key selects digits. and adds or decreases number.
E2 Delete Remote Control
1. Press “ ” key 2 seconds, screen displays F1
2. Press “ ” key, screen displays F2, press “ ” screen displays E1, press “ ” to display
E2
3. Press “ ” to confirm, screen displays 0001, “1”is flashing, and press “ ” “ ” key to
select the number you want delete.
4. Press “ ” key, you will hear a voice (success), means number has been deleted
successfully.
5. Press “ ” it will exit to “E2”, press “ ” again to exit setting state
E3 Delete Alarm Function Transmitters
1. Press “ ” key 2 seconds, screen displays F1
2. Press “ ” key, screen displays F2, press “ ” screen displays E1, press “ ” two times
to display E3
3. Press “ ” to confirm, screen displays 0001, “1”is flashing, and press “ ” “ ” key to
select the number you want delete.
4. Press “ ” key, you will hear a voice (success), means number has been deleted
successfully.
5. Press “ ” it will exit to “E3”, press “ ” again to exit setting state
E4 Delete Cancel Function Transmitters
1. Press “ ” key 2 seconds, screen displays F1
2. Press “ ” key, screen displays F2, press “ ” screen displays E1, press “ ” to display
E4
3. Press “ ” to confirm, screen displays 0001, “1”is flashing, and press “ ” “ ” key to
select the number you want delete.
4. Press “ ” key, you will hear a voice (success), means number has been deleted
successfully.
5. Press “ ” it will exit to “E4”, press “ ” again to exit setting state

3
F3 Display Setting
E1 Display Mode
1. Press “ ” key 2 seconds, screen displays F1
2. Press “ ” key two times to display F3, press “ ” screen displays E1
3. Press “ ” to display 1 or 2, and then select the one you want
“1”means live mode- -means when No.1 No.2 No.3 call in turn, the screen shows 0003
0002 0001. Newest call number shows on the top of screen.
“2”means the queue mode- -means when No.1 No.2 No.3 call in turn, the screen shows
0001 0002 0003. Oldest call number shows on the top of screen.
4. Press “ ” it will exit to “E1”,.
5. Press “ ” again to exit setting state
E2 Storage Number
1. Press “ ” key 2 seconds, screen displays F1
2. Press “ ” key two times, screen displays F3, press “ ” screen displays E1, press “ ”
to display E2
3. Press “ ” to confirm, press “”” ”to select the number from 0001-999
4. Press “ ” it will exit to “E2”,.
5. Press “ ” again to exit setting state
F4 Logout Setting (Remove Timing Setting)
1. Press “ ” key 2 seconds, screen displays F1
2. Press “ ” key three times, screen displays F4, press “ ” screen displays 00(or other
number).
3. Press “”” ”to choose the number from 00-99
“00”means the number will be steady until it is canceled.
“01-99”means the time the last call will be displayed. If you choose 50, it means last
number will be displayed for 50 seconds on screen. When time is up, this number will be
deleted automatically
4. Press “ ” it will exit to “F4”,.
5. Press “ ” again to exit setting state
F5 Cycle Mode
1. Press “ ” key 2 seconds, screen displays F1
2. Press “ ” key four times, screen displays F5, press “ ” screen displays 00(or other
number)
3. Press “”” ”to select the number from 00-99
“00”means the number will be steady
“01-99”. For example, if you choose 10 seconds, it means each 10 seconds number will
cycle one time.
4. Press “ ” it will exit to “F5”,.
5. Press “ ” again to exit setting state
F6 Voice Setting
E1 Voice Mode
1. Press “ ” key 2 seconds, screen displays F1
2. Press “ ” key five times, screen displays F6, press “ ” screen displays E1
3. Press “ ” to confirm, screen displays 0(or other number)
4. Press “”” ”to choose the number from 0-7
“0”means English pronunciation (number and service type)
“1”means English pronunciation (number only)
“2”means English pronunciation (eg.No.15: Fifteen + service type)
“3”means English pronunciation (eg.No.15: Fifteen)
“4”means Ding Dong voice alert
“5”means music alert 1
“6”means music alert 2
“7”means warning sound
5. Press “ ” it will exit to “E1”,.
6. Press “ ” again to exit setting state

4
E2 The times of Voice Announcements (Default:1 time)
1. Press “ ” key 2 seconds, screen displays F1
2. Press “ ” key five times, screen displays F6, press “ ” screen displays E1, press “ ”
to display E2
3. Press “ ” to confirm, screen displays 1(or other number)
4. Press “ ”“”to select the number from 1 to 9.
5. Press “ ” it will exit to “E2”,.
6. Press “ ” again to exit setting state
E3 Alert voice of cycling（Whether to read the number while on cycling
mode）
1. Press “ ” key 2 seconds, screen displays F1
2. Press “ ” key five times, screen displays F6, press “ ” screen displays E1, press “ ”
two times to display E3
3. Press “ ” to confirm, screen displays “0”or “1”
4. Press “ ”” ”to select the number you want.
“0”means no voice alert while cycling. If you choose “0”means, No.1 2 3 4 5 etc. will
show circularly without ringing.
“1”means with alert while cycling. If you choose “1”means, No.1 2 3 4 5 etc. will show
circularly while ringing.
5. Press “ ” it will exit to “E3”,.
6. Press “ ” again to exit setting state
E4 Volume Setting (Default: 6)
1. Press “ ” key 2 seconds, screen displays F1
2. Press “ ” key five times, screen displays F6, press “ ” screen displays E1, press “ ”
three times to display E4
3. Press “ ” to confirm, screen displays “0”(or other number)
4. Press “ ”” ”to select the number you want.
“1” is mute. 9 is highest volume.
5. Press “ ” it will exit to “E4”,.
6. Press “ ” again to exit setting state
E5 Brightness setting (Default: 3)
1. Press “ ” key 2 seconds, screen displays F1
2. Press “ ” key five times, screen displays F6, press “ ” screen displays E1, press “ ”
four times to display E5
3. Press “ ” to confirm, screen displays “0”(or other number)
4. Press “ ”” ”to select the number you want.
“1” is darkest. “7”is brightest.
5. Press “ ” it will exit to “E5”,.
6. Press “ ” again to exit setting state
E6 Operational sound navigation
0---OFF 1----OPEN
E7“Number”position
0---Number 0001 CALL(English Way)
1---0001 Number CALL(Chinese Way)
E8 To be developed
E9 Whether to read Counter Number (Suit for queue call system)
0---Please Number xxx go to Counter xx + Service type
1---Please Number xxx to to Counter + Service type
F7 Keyboard Setting (Default: OFF)
E1 Partition Setting
1. Press “ ” key 2 seconds, screen displays F1
2. Press “ ” key six times, screen displays F7, press “ ” screen displays E1
3. Press “ ” to confirm, screen displays “OF”or “ON”or “1” “2”“3”“4”“5”“6”“7”“8”
“9”“0”“A”“ b”“ c”“ d”“ E”
“OF”means display can’t receive all signals from all different partition’s keyboard
“ON”means display can receive all signals from all different partition’s keyboard number
0001-9999
“0” or “1”or “2”…… “E”means display only can receive one partition’s signal
4. Press “ ”” ”to select the number you want.
5. Press “ ” it will exit to “E1”,.
6. Press “ ” again to exit setting state

5
NOTE: If the keyboard in partition 5, display also selects 5, it means display can receive all
signals 0001-9999 from keyboard.
F8 Key Settings
E1 Single-key or Multi-key Setting
1---Single key
2---Multi key
E2 Voice pairing
1. Press “ ” key 2 seconds, screen displays F1
2. Press “ ” key seven times, screen displays F8, press “ ” screen displays E1
3. Press “ ” to display E2 and Press “ ” to confirm, and you will see 00 (sound cancel)
4. Press “ ”” ”to select the number (voice) you want.
For example, if you want “emergency”, you select 26 , And press “emergency “ key from
button. Then you will hear success.
5. Press “ ” again to exit setting state
When you press Emergency button, you will hear “XX number Emergency”
F9 Restore factory setting
1. Press “ ” key 2 seconds, screen displays F1
2. Press “ ” key 8 times, screen displays F9, press “ ” screen displays E1
3. Keep press “ ” 2 seconds to confirm, you will hear a voice (success),
F0 Date &Time Setting
Enter F0, you will see the Minute Area is flashing, use “ ”“”to adjust the
minute.
Press the “ ” key, to navigate.. After setting the time and date, Press “ ” again to exit
setting state