CHIEF RFWD-110 User manual

1
WARNINGS
WARNING The maximum weight to be installed on the RFWD wall mount is 40 lbs. (18.1 kg).
WARNING The RFWD is designed to be installed using wall studs or supporting framework.
The structure to which the RFWD wall mount is anchored must be capable of
supporting five times the total weight of the mount and all attached equipment.
CAUTION To prevent damage to the RFWD, which could affect or void the Factory warranty,
and to the equipment that will be attached to it, thoroughly study all instructions
and illustrations before you begin the installation.
CAUTION If your monitor uses a longer screw size other than those included in the kit,
DO NOT use the screws provided with the mount. Use the screws provided with
your monitor or contact the manufacturer. Using the wrong screws could result in
damage to your monitor.
If you have any questions about this installation, contact Chief Manufacturing at:
1.800.572.1373 or 952.277.3901.
LCD T
V
INSTALLATION
INSTRUCTIONS
(RFWD-110)
DUAL Swing Arm
WALL MOUNT

80 70
ASSEMBLY DIAGRAM
LCD TV WALL MOUNT DUAL Swing Arm (RFWD-110)
20
30 or 50 (optional)
10
40 or 60
(
o
p
tional
)
110
100
Cable Mana
g
ement Slots
90
120
PART PART NAME QTY NOTES
10 SINGLE SWING ARM 1
20 SCREW, PHILLIPS PAN HEAD, M4 X 12MM 4
FLUSH
MOUNT
30 SCREW, PHILLIPS PAN HEAD, M4 X 20MM (USE WITH 40) * 4
40 3/8” SPACER 4
50 SCREW, PHILLIPS PAN HEAD, M4 X 30MM (USE WITH 60) ** 4
60 3/4” SPACER 4
RECESSED
MOUNT
70 WASHER 2
80 SCREW, WOOD 2
90 BRACKET, WALL 1
100 PLATE, COVER, CABLE MANAGEMENT 2
110 SCREW, COVER, CABLE MANAGEMENT 4
120 SCREW, SET 1
• *Use M4 x 20mm screws (30) with spacers (40) for recessed applications.
• **Use M4 x 30mm screws (50) with spacers (60) for recessed applications.
2

INSTALLATION INSTRUCTIONS
A. Determine the exact mounting location prior to installation,
considering screen size as well as the mount swing and extension
radius.
Step 1
B. Use the wall bracket (90) as a template and drill two 3/32” pilot
holes to a minimum depth of 1 1/2”.
C. Check wall bracket to ensure it is level and adjust to level if
necessary.
D. Use two wood screws (80) and two #10 washers (70) to secure the
wall bracket (90).
Flushed Mount or Recessed Mount
Step 2 NOTE: This manual contains two sets of Installation Instructions,
listed below. Choose the set of instructions that applies to the
type of installation you want.
• Flush Mount Applications do not use spacers. The monitor
is attached to the mount with four screws.
• Recessed Mount Applications use spacers. The monitor
is attached to the mount with four screws and four
spacers.
CAUTION: If monitor uses a screw size other than those included in the
kit, DO NOT use the screws provided. Using the wrong screws
could result in damage to your monitor.
Flushed Mount
A. Install two screws (20) in to the top mounting holes of your monitor.
B. Align the hole-pattern of your display with the screws installed on
the mount and hang the mount from the two screws.
C. Install two remaining screws (20) through the mount and into the
mounting holes of your display.
Recessed Mount
NOTE: Use one of the following screw and spacer combinations:
(30 with 40) or (50 with 60).
A. Select four screws (30 or 50) for the Flush application.
B. Select the four spacers (40 or 60) for the Flush application.
C. Set four spacers (40 or 60) over the four mounting holes on your
monitor.
D. Install two screws (30 or 50) in to the top mounting holes of your
monitor.
E. Align the hole-pattern of your display with the screws installed on
the mount and hang the mount from the two screws.
F. Install two remaining screws (30 or 50) through the mount and into
the mounting holes of your display.
3

CAUTION: Over-tightening adjustment bolt will
cause excessive wear and may
distort adjustment components.
To adjust the tension of the spherical movement,
the arm movement, and the lateral movement:
1. Slightly tighten or loosen the tension
adjustment bolt indicated at the right.
2. Check for desired tension.
3. Repeat as necessary.
INSTALLATION INSTRUCTIONS (Continued)
A. Place the top of the mount on top of the wall bracket (90) and push
the bottom onto the wall bracket.
Step 3
B. Secure your display to the wall by tightening the set screw (120).
Cable Connection CAUTION: Make sure your cables do not run through a pinch point.
Connect and secure power/audio/video cables, making sure to leave
sufficient slack to allow for movement of the display. Secure cables using
cover plates (100) and four screws (110).
TENSION ADJUSTMENTS
Lateral Tension
A
d
j
ustment Bolts
Spherical Movement
Tension Adjustment Bolt
4

THIS PAGE
INTENTIONALLY
LEFT BLANK
5