Chromalox DSR-5716P User manual

(Supersedes PK435-4)
PK435-5
WR
161-048630-001
JUNE, 1994
4
Installation
and
OPERATION INSTRUCTIONS
Type WR-80EP Explosion Proof Room Thermostat
© 2010 Chromalox, Inc.
Specifications – Table A
GENERAL
Positive accuracy, long and reliable service, 3° differential. Heavy-
duty, single stage, SPST line voltage snap-acting switch. Patented
hydraulic element. WR-80EP has external, coiled sensing element and
a low position which drops control point to keep heater off.
Uses — Automatically controls room temperature by turning electric
air heaters on and off. Can be used to control the air heaters directly,
within thermostat rating. For higher ratings use thermostat with mag-
netic contactor. Place thermostat on inside wall, away from undue
heating or cooling influences, about 4 feet above the floor. The explo-
sion proof WR-80EP is suitable for Class I, Group D and Class II,
Groups E, F and G locations.
NOTICE: Type WR thermostats are designed for temperature control
service only. Because they do not fail safe, they should not be used for
temperature limiting duty.
WARNING: Users should install adequate back-up con-
trols and safety devices with their electric heating
equipment. Where the consequences of failure may
be severe, back-up controls are essential. Although
the safety of the installation is the responsibility of
the user, Chromalox will be glad to assist in making
equipment recommendations.
Principle of Operation — Control action of these thermostats is pro-
vided through the principle of liquid volume change. With a variation in
temperature, the liquid in the sensing element expands or contracts,
causing a bellows to actuate the switching mechanism.
Housing — The control housing and cover assembly is of heavy-duty
cast aluminum.
Temp. Maximum Rating
Range
Model (°F) 120V a-c † 115V d-c 240V a-c † 230V d-c 277V a-c 480V a-c
125Va pilot 125Va pilot 125Va pilot
WR-80EP 40-90 25 amps duty (use 22 amps duty (use 18 amps duty (use
or 3000 with d-c or 5280 with d-c or 5000 with a-c
total watts contactor) total watts contactor) total watts contactor)
† d-c ratings not UL listed
4”
61/8”
21/2”
311/16”
WR-80EP
40 to 90°F
UL Listed
MOUNTING
Note: Do not mount control where it will be subject to vibration,
shock, grease, dust, lint or corrosive vapors. Do not mount adjacent to
a large magnetic contactor, as vibration and shock will cause thermo-
stat to interact erratically – resulting in chattering of the contactor.
WARNING: Do not twist or uncoil the coiled element
on top of the case.
The proper location of a heavy duty room thermostat is important to
assure good performance.
1. Locate where air circulates freely.
2. Never install on or near outside wall.
3. Keep away from windows or doors.
4. Do not locate too close to strong light or other false source of heat,
such as sunlight, steam lines, etc.
5. If electrical conduit leads into cooler or warmer room, plug up
space around wires in the conduit with rock wool.
1 /
116
1 /
116
11
16
1 /
11
16
3 /
58
4 /
58
4 /
4
1
6 /
8
1516
2 /
12
/ -14
N.P.T. Thread
4-Holes
/ " Dim.
516
58
/
Figure 1

1347 HEIL QUAKER BLVD., LAVERGNE, TN 37086
Phone: [phone] www.chromalox.com
WARNING: Hazard of Electric Shock. Extreme care
should be exercised during calibration adjustments
because of shock hazard due to exposed electrical
terminals.
DANGER: Calibration will involve exposure of inter-
nal control terminals to ambient conditions during
some part of the recalibration procedure.
Combustible materials which cause hazardous
conditions must not be present during recalibra-
tion process – otherwise explosion may result.
WR-80EP thermostats are accurately calibrated at the factory
so the dial setting correctly indicates the temperature at which the
contacts open on temperature rise. If, as a result of damage in tran-
sit or for other reasons the room temperature differs appreciably
from the dial setting, the calibration may be adjusted as follows:
1. Note temperature on the thermometer.
2. Set dial at highest temperature.
3. Turn dial slowly to lower temperature and stop when thermo-
stat contacts open.
4. Remove cover using the 3/16” Allen Head Wrench as in #1
wiring.
5. Loosen two dial screws (Figure 2). Carefully turn the dial only
to correct temperature setting as indicated by thermometer. Be
sure the thermostat shaft is not moved during this operation.
6. Tighten the dial screws and replace thermostat cover. (See
“Replacing Cover”)
CALIBRATION
Ground
WIRING
WARNING: Hazard of Electric Shock. Disconnect all
power before wiring or servicing this control.
1. After a suitable location has been chosen for the control,
remove the front cover by using a 3/16” Allen Head Wrench,
(furnished with control) in the 6 cover screws.
2. Electric wiring to heater must be installed in accordance with
National Electrical Code and with local codes. WARNING:
Use copper conductors only.
3. Entrance for wiring is provided by one 1/2-14 NPT hole in the
bottom of the housing. Wiring to control housing must be in
rigid conduit also in accordance with National Electrical Codes
(NEC) for hazardous locations. (See Figure 2)
4. Connect wires according to wiring diagrams (Figures 3 and 4).
Note: Electrical connections should be made with generous
loops of wire – approximately 6” per lead.
Note: If load amperage or voltage rating exceeds switch rating,
a contactor must be used. Contactor and wiring to be supplied
by customer. (See Figure 4)
Replacing Cover
1. Set the internal dial and the external dial to the same setting so
that the hole in the dial lines up with pin on the arm that is
operated by the knob. (See Figure 2)
2. Replace 6 cover screws and tighten with Allen Wrench provided.
Ground
Figure 2
Figure 3 — Single phase loads when load does not exceed
rating of thermostat.
Figure 4 — Single phase loads when load exceeds rating of thermostat and three
phase loads.
Ground
Fixed
Indicator
1/2-14
N.P.T. Thread
Electrical
Connections
Limited Warranty:
Please refer to the Chromalox limited warranty applicable to this product at
http://www.chromalox.com/customer-service/policies/termsofsale.aspx.