Cisco Quad Camera User manual

Cisco Quad Camera, Precision 60, SpeakerTrack 60 and PTZ-12 Camera
D15296.10 Cisco Quad Camera, Precision 60, SpeakerTrack 60, and PTZ-12 Camera SEPTEMBER 2019. Copyright © 2019 Cisco Systems, Inc. All rights reserved.
1
Camera guide
SEPTEMBER 2019
SpeakerTrack 60
Precision 60
Camera guide
for Cisco Quad Camera, Cisco TelePresence Precision 60, Cisco TelePresence SpeakerTrack 60, and PTZ-12
P T Z-12
Quad Camera
Contents
Introduction
Physical interface
Connecting to a codec
Appendix
Factory reset

Cisco Quad Camera, Precision 60, SpeakerTrack 60 and PTZ-12 Camera
D15296.10 Cisco Quad Camera, Precision 60, SpeakerTrack 60, and PTZ-12 Camera SEPTEMBER 2019. Copyright © 2019 Cisco Systems, Inc. All rights reserved.
2
Camera guide
Table of Contents
Introduction ......................................................................3
User documentation and software.....................................4
Products covered in this guide.......................................4
User documentation .......................................................4
Software .........................................................................4
Physical interface .............................................................5
Quad Camera .....................................................................6
Precision 60 Camera..........................................................7
SpeakerTrack 60 Camera...................................................8
P T Z-12 C a m e r a ..................................................................9
Connecting to a codec ...................................................10
Codec compatibility.......................................................... 11
Software compatibility......................................................12
CE software ..................................................................12
RoomOS software ........................................................12
Connect Quad Camera to Codec Pro ..............................13
Connect Quad Camera to Codec Plus .............................14
Connect Quad Camera to SX80 Codec ...........................15
Connect Precision 60 to Codec Pro.................................16
Connect Precision 60 to Codec Plus ............................... 17
Connect Precision 60 to SX80 Codec .............................18
Connect SpeakerTrack 60 to Codec Pro..........................19
Connect SpeakerTrack 60 to SX80 Codec ..................... 20
Connect SpeakerTrack 60 to Codec C40 ........................21
Connect SpeakerTrack 60 to Codec C60 ........................22
Connect SpeakerTrack 60 to Codec C90 ....................... 23
Connect PTZ-12 to Codec Plus........................................24
Connect PTZ-12 to Codec Pro .........................................25
Connect PTZ-12 to SX80 Codec..................................... 26
Connecting multiple cameras to the Codec Pro ..............27
Main camera .................................................................27
Using the HD-BNC connector ......................................27
Adding multiple cameras ..............................................27
Connecting multiple cameras to the SX80 codec........... 28
Main camera ................................................................ 28
Using the analog video or DVI-I inputs ........................ 28
Adding multiple cameras ............................................. 28
Factory reset ..................................................................29
Quad Camera .................................................................. 30
Precision 60 Camera........................................................ 31
SpeakerTrack 60 Camera.................................................32
Factory resetting the device.........................................32
Factory resetting the cameras..................................... 33
Appendix ........................................................................34
Technical specifications................................................... 35
Quad Camera............................................................... 35
Precision 60 Camera ................................................... 36
SpeakerTrack 60 Camera .............................................37
P T Z-12 C a m e r a ............................................................ 38
Contact us ....................................................................... 39
Thank you for choosing Cisco!
Your Cisco product has been designed to give you many
years of safe, reliable operation.
This guide describes the Quad Camera, Precision 60,
SpeakerTrack 60, and PTZ-12 Camera.
May we recommend you to visit the Cisco website regu-
larly for updated versions of the user documentation.
The user documentation can be found at:
https://www.cisco.com/go/telepresence/docs
https://www.cisco.com/go/room-docs
How to use this guide
The top menu bar and the entries in the Table of Contents
are all hyperlinks. You can click on them to go to the topic.
Contents
Introduction
Physical interface
Connecting to a codec
Appendix
Factory reset
Contents

Cisco Quad Camera, Precision 60, SpeakerTrack 60 and PTZ-12 Camera
D15296.10 Cisco Quad Camera, Precision 60, SpeakerTrack 60, and PTZ-12 Camera SEPTEMBER 2019. Copyright © 2019 Cisco Systems, Inc. All rights reserved.
3
Camera guide
CHAPTER 1
Introduction
Contents
Introduction
Physical interface
Connecting to a codec
Appendix
Factory reset
Introduction

Cisco Quad Camera, Precision 60, SpeakerTrack 60 and PTZ-12 Camera
D15296.10 Cisco Quad Camera, Precision 60, SpeakerTrack 60, and PTZ-12 Camera SEPTEMBER 2019. Copyright © 2019 Cisco Systems, Inc. All rights reserved.
4
Camera guide
User documentation and software
Products covered in this guide
Cisco Quad Camera
Cisco TelePresence Precision 60 Camera
Cisco TelePresence SpeakerTrack 60 Camera
Cisco PTZ-12 Camera
User documentation
This guide provides you with information required to install the
cameras on the video system.
The video system can be registered to an on-premise service
(CUCM, VCS) or registred to our cloud service (Cisco Webex).
Documentation on the Cisco website
Visit the Cisco website regularly for updated versions of the
guides:
https://www.cisco.com/go/telepresence/docs
https://www.cisco.com/go/room-docs
Explore the Cisco Project Workplace to find inspiration and
guidelines when preparing your office or meeting room for
video conferencing:
https://www.cisco.com/go/projectworkplace
Software
The camera software is automatically upgraded through
the codec for the Precision 60, SpeakerTrack 60 and Quad
Camera. For the PTZ-12 camera no software upgrade applies.
For more information, see theSoftware compatibility chapter.
Download software for the video system from the Cisco web
site: https://software.cisco.com/download/home
We recommend reading the Software release notes (CE9):
Cisco Collaboration Endpoint Software 9
Contents
Introduction
Physical interface
Connecting to a codec
Appendix
Factory reset
Introduction

Cisco Quad Camera, Precision 60, SpeakerTrack 60 and PTZ-12 Camera
D15296.10 Cisco Quad Camera, Precision 60, SpeakerTrack 60, and PTZ-12 Camera SEPTEMBER 2019. Copyright © 2019 Cisco Systems, Inc. All rights reserved.
5
Camera guide
CHAPTER 2
Physical interface
Contents
Introduction
Physical interface
Connecting to a codec
Appendix
Factory reset
Physical interface

Cisco Quad Camera, Precision 60, SpeakerTrack 60 and PTZ-12 Camera
D15296.10 Cisco Quad Camera, Precision 60, SpeakerTrack 60, and PTZ-12 Camera SEPTEMBER 2019. Copyright © 2019 Cisco Systems, Inc. All rights reserved.
6
Camera guide
Quad Camera
Video
• HDMI 1 is the main video source. The maximum resolution
is 1080p60.
• For long cable lengths, HDMI extenders supporting EDID
should be used. The extender must not alter the SPA
address or any EDID information incorrectly. The extender
must support ARC (Audio Return Channel) when used
with the Codec Plus or Codec Pro.
• If EDID is not supported, use the following setting:
Cameras > Camera n > AssignedSerialNumber
This setting allows you to manually assign a camera ID to
a camera by associating the camera ID with the camera’s
serial number. The setting is persistent until the codec is
factory reset.
Power
• Power rating: 12 VDC, 5.83 A.
• Always use the provided cables and power adapter.
Ethernet
For camera control and software upgrades.
Use Ethernet cable only. Do not connect a serial VISCA
cable to the Ethernet port on the Precision 60 camera,
as this will cause severe damage to the camera.
Kensington lock
The Kensington lock may be used to prevent the camera from
being moved from its place or to prevent theft.
For more information about the Quad Camera setup, refer to
the following installation guides:
Cisco Webex Room Kit Pro installation guide
Cisco Webex Room Kit Plus installation guide
Cisco TelePresence SX80 Integrator Package with Quad
Camera installation guide
The LED is lit during a call.
Camera control
(Ethernet)
Pinhole for
factory reset
Power input
Sub-woofer
output
HDMI outputs
1080p60
USB 2.0
Type A
Line input
Maintenance
(micro USB)
Power
On/Off
The LED is continuously lit when power is On.
Kensington lock
Contents
Introduction
Physical interface
Connecting to a codec
Appendix
Factory reset
Physical interface

Cisco Quad Camera, Precision 60, SpeakerTrack 60 and PTZ-12 Camera
D15296.10 Cisco Quad Camera, Precision 60, SpeakerTrack 60, and PTZ-12 Camera SEPTEMBER 2019. Copyright © 2019 Cisco Systems, Inc. All rights reserved.
7
Camera guide
Precision 60 Camera
Video
• HDMI is the main video source. The maximum resolution
is 1080p60.
• 3G-SDI is the secondary video source. The maximum
resolution is 1080p60.
• For long cable lengths, HDMI extenders supporting EDID
should be used. The extender must not alter the SPA
address or any EDID information incorrectly.
• If EDID is not supported, use the following setting:
Cameras > Camera n > AssignedSerialNumber
This setting allows you to manually assign a camera ID to
a camera by associating the camera ID with the camera’s
serial number. The setting is persistent until the codec is
factory reset.
Power
• Power rating: 12 VDC, 3 A.
• Always use the provided cables and power adapter.
Ethernet
For camera control and software upgrades.
Use Ethernet cable only. Do not connect a serial VISCA
cable to the Ethernet port on the Precision 60 camera,
as this will cause severe damage to the camera.
Kensington lock
The Kensington lock may be used to prevent the camera from
being moved from its place or to prevent theft.
For more information about the Precision 60 setup, refer to
the following installation guides:
Cisco Webex Room Kit Plus Precision 60 Installation Guide
Cisco Webex Room Kit Pro Precision 60 Installation Guide
Cisco TelePresence SX80 Installation Guide
The LED is lit during a call.
The LED is continuously lit when power is On.
Power
supply
Ethernet
RJ45
HDMI Video
out
3G-SDI out
Display port*
Kensington lock
* For future use
Pinhole for
factory reset
Contents
Introduction
Physical interface
Connecting to a codec
Appendix
Factory reset
Physical interface

Cisco Quad Camera, Precision 60, SpeakerTrack 60 and PTZ-12 Camera
D15296.10 Cisco Quad Camera, Precision 60, SpeakerTrack 60, and PTZ-12 Camera SEPTEMBER 2019. Copyright © 2019 Cisco Systems, Inc. All rights reserved.
8
Camera guide
SpeakerTrack 60 Camera
Video
• Two HDMI cables from the cameras.
Power
• Power rating: 12 VDC, 6.5 A.
• Always use the provided cables and power adapter.
• Power out to cameras (internal connection).
Ethernet
Two Ethernet ports are used for the internal camera control con-
nection. The third connector is used for connecting the codec.
Use Ethernet cable only. Do not connect a serial VISCA
cable to the Ethernet port on the SpeakerTrack 60 camera,
as this will cause severe damage to the camera.
Microphone connectors
The right set is used for internal connection to the microphone
panel. The left set of connectors is intended for future use.
Kensington lock
The Kensington lock may be used to prevent the camera from
being moved from its place or to prevent theft.
For more information about the SpeakerTrack 60 setup, refer to
the following installation guides:
Cisco TelePresence SpeakerTrack 60 installation guide
Cisco Webex Codec Pro installation guide
Cisco TelePresence SX80 Installation Guide
During a call, the LED is lit on the camera
that is currently sending the live picture.
The status LED is continuously lit when
power is On.
Power out to
cameras
Ethernet
RJ45
codec
Ethernet
RJ45
camera control
Additional
connectors*
Power in USB*
Microphones
on panel
Chinch
connectors*
* For future use
Contents
Introduction
Physical interface
Connecting to a codec
Appendix
Factory reset
Physical interface

Cisco Quad Camera, Precision 60, SpeakerTrack 60 and PTZ-12 Camera
D15296.10 Cisco Quad Camera, Precision 60, SpeakerTrack 60, and PTZ-12 Camera SEPTEMBER 2019. Copyright © 2019 Cisco Systems, Inc. All rights reserved.
9
Camera guide
P T Z-12 C a m e r a
Video
• HDMI is the main video source. The maximum resolution is
1080p60.
Power
• Power rating: 12 VDC, 1.4 A.
• Always use the provided cables and power adapter (12VDC,
JEITA type4). Do NOT use any other AC power adaptor.
Ethernet
For camera control.
Factory reset
A factory reset should only be performed by a system adminis-
trator or in contact with Cisco technical support.
For more information about the PTZ-12 setup, refer to the
Cisco Webex Room Kit Plus PTZ-12 installation guide
Not in use
HDMI video
connector
Ethernet
Camera
control
Power input
Factory reset
Screw holes (for
camera mounting)
Screw holes (for
camera mounting)
VISCA/LAN switch
(Switch 1: on; Switch
2-8: OFF)
Tripod (for camera
mounting)
The LED is green when the
power is On. The LED is
off when the system is on
standby mode.
The LED is amber
when the camera is on
standby mode.
Bottom view
Not in use
Contents
Introduction
Physical interface
Connecting to a codec
Appendix
Factory reset
Physical interface

Cisco Quad Camera, Precision 60, SpeakerTrack 60 and PTZ-12 Camera
D15296.10 Cisco Quad Camera, Precision 60, SpeakerTrack 60, and PTZ-12 Camera SEPTEMBER 2019. Copyright © 2019 Cisco Systems, Inc. All rights reserved.
10
Camera guide
CHAPTER 3
Connecting to a codec
Contents
Introduction
Physical interface
Connecting to a codec
Appendix
Factory reset
Connecting to a codec

Cisco Quad Camera, Precision 60, SpeakerTrack 60 and PTZ-12 Camera
D15296.10 Cisco Quad Camera, Precision 60, SpeakerTrack 60, and PTZ-12 Camera SEPTEMBER 2019. Copyright © 2019 Cisco Systems, Inc. All rights reserved.
11
Camera guide
Codec compatibility
Quad Camera
The Quad Camera is compatible with the following codecs:
• Cisco Webex Codec Pro
• Cisco Webex Codec Plus
• Cisco TelePresence SX80 codec
Precision 60
The Precision 60 camera is compatible with the following
codecs:
• Cisco Webex Codec Pro
• Cisco Webec Codec Plus
• Cisco TelePresence SX80 codec
SpeakerTrack 60
The SpeakerTrack 60 system is compatible with the following
codecs:
• Cisco Webex Codec Pro
• Cisco TelePresence SX80 codec
• Cisco TelePresence C90 codec
• Cisco TelePresence C60 codec
• Cisco TelePresence C40 codec
P T Z-12
The PTZ-12 Camera is compatible with the following codecs:
• Cisco Webex Codec Plus
• Cisco Webex Codec Pro
• Cisco TelePresence SX80 codec
Cisco TelePresence Codec SX80
Cisco TelePresence Codec C40/C60
Cisco TelePresence Codec C90
Cisco Webex Codec Plus
Cisco Webex Codec Pro
Contents
Introduction
Physical interface
Connecting to a codec
Appendix
Factory reset
Connecting to a codec

Cisco Quad Camera, Precision 60, SpeakerTrack 60 and PTZ-12 Camera
D15296.10 Cisco Quad Camera, Precision 60, SpeakerTrack 60, and PTZ-12 Camera SEPTEMBER 2019. Copyright © 2019 Cisco Systems, Inc. All rights reserved.
12
Camera guide
Software compatibility
CE software
The camera software for the Quad Camera, Precision 60 and SpeakerTrack 60 cameras is automatically upgraded through the codec.
For the PTZ-12 camera no software upgrade applies.
Minimum CE software version requirement for the codecs can be found in the table below:
Codec C90 Codec C40/C60 Codec SX80 Codec Plus Codec Pro
Quad Camera N/A N/A CE 9.2 CE 9.1 CE 9.4
Precision 60 N/A N/A TC 7.1, CE 8.1 CE 9.1 CE 9.4
SpeakerTrack 60 TC 7.1 TC 7.1 TC 7.1, CE 8.1 N/A CE 9.4
P T Z-12 *N/A N/A CE 9.6 CE 9.6 CE 9.6
RoomOS software
The camera software for the Quad Camera, Precision 60 and SpeakerTrack 60 cameras is automatically upgraded through the codec when a new version is available from the cloud service.
For the PTZ-12 camera no software upgrade applies.
* Only one PTZ-12 camera is supported on CE9.6. Multiple PTZ-12 cameras are supported from CE9.7.
Contents
Introduction
Physical interface
Connecting to a codec
Appendix
Factory reset
Connecting to a codec

Cisco Quad Camera, Precision 60, SpeakerTrack 60 and PTZ-12 Camera
D15296.10 Cisco Quad Camera, Precision 60, SpeakerTrack 60, and PTZ-12 Camera SEPTEMBER 2019. Copyright © 2019 Cisco Systems, Inc. All rights reserved.
13
Camera guide
Connect Quad Camera to Codec Pro
• Connect the HDMI cable between the camera and the codec. The
cable transmits video from the camera to the codec, and audio
from the codec to the loudspeakers in the camera (Audio Return
Channel - ARC).
Codec: Always use Connector 1 (HDMI input) for the main camera.
Camera: Connect to connector 1 (HDMI output).
• Connect the camera control cable (Ethernet) between the camera
control ports on the camera and codec. The connectors are
marked with the camera control symbol.
• Connect the power adapter to the camera and connect to power.
• Connect other codec cables as described in theCisco Webex
Room Kit Pro installation guide.
Power
(100-240 VAC, 50/60 Hz)
Power
adapter
Always use the provided power cable
and adapter.
RJ45 HDMI
Contents
Introduction
Physical interface
Connecting to a codec
Appendix
Factory reset
Connecting to a codec

Cisco Quad Camera, Precision 60, SpeakerTrack 60 and PTZ-12 Camera
D15296.10 Cisco Quad Camera, Precision 60, SpeakerTrack 60, and PTZ-12 Camera SEPTEMBER 2019. Copyright © 2019 Cisco Systems, Inc. All rights reserved.
14
Camera guide
Connect Quad Camera to Codec Plus
• Connect the HDMI cable between the camera and the codec. The
cable transmits video from the camera to the codec, and audio
from the codec to the loudspeakers in the camera (Audio Return
Channel - ARC).
Codec: Always use Connector 1 (HDMI input) for the main camera.
Camera: Connect to connector 1 (HDMI output).
• Connect the camera control cable (Ethernet) between the camera
control ports on the camera and codec. The connectors are
marked with the camera control symbol.
• Connect the power adapter to the camera and connect to power.
• Connect other codec cables as described in theCisco Webex
Room Kit Plus installation guide.
RJ45 HDMI
Power
(100-240 VAC, 50/60 Hz)
Power
adapter
Always use the provided power cable
and adapter.
Contents
Introduction
Physical interface
Connecting to a codec
Appendix
Factory reset
Connecting to a codec

Cisco Quad Camera, Precision 60, SpeakerTrack 60 and PTZ-12 Camera
D15296.10 Cisco Quad Camera, Precision 60, SpeakerTrack 60, and PTZ-12 Camera SEPTEMBER 2019. Copyright © 2019 Cisco Systems, Inc. All rights reserved.
15
Camera guide
Connect Quad Camera to SX80 Codec
• Connect the HDMI cable between the camera and the codec. The
cable transmits video from the camera to the codec.
Codec: Always use Connector 1 (HDMI input) for the main camera.
Camera: Connect to connector 1 (HDMI output).
• Connect the camera control cable (Ethernet) between the camera
control ports on the camera and codec.
Codec: Connect to the codec’s 2nd or 3rd Ethernet port.
Camera: The connector is marked with the camera control symbol.
Connect a network switch to the codec’s 2nd or 3rd Ethernet port
if you need more than two ports to support your device.
• Connect the audio cable between the loudspeaker output on the
codec and the line input on the Quad Camera. The cable trans-
mits audio from the codec to the loudspeakers in the camera.
• Connect the power adapter to the camera and connect to power.
• Connect other codec cables as described in theCisco
TelePresence SX80 Integrator Package with Quad Camera
Installation Guide.
RJ45 HDMI
Power
(100-240 VAC, 50/60 Hz)
Power
adapter
Always use the provided power cable
and adapter.
3.5 mm
mini-jack,
3-pin
3.5 mm
Euroblock
Contents
Introduction
Physical interface
Connecting to a codec
Appendix
Factory reset
Connecting to a codec

Cisco Quad Camera, Precision 60, SpeakerTrack 60 and PTZ-12 Camera
D15296.10 Cisco Quad Camera, Precision 60, SpeakerTrack 60, and PTZ-12 Camera SEPTEMBER 2019. Copyright © 2019 Cisco Systems, Inc. All rights reserved.
16
Camera guide
Connect Precision 60 to Codec Pro
• Connect the video cable (HDMI) between the camera and codec.
Codec: Always use Connector 1 (HDMI input) for the main camera.
Camera: Connect to the HDMI output.
• If you use a coaxial cable for video, you will need a BNC to
HD-BNC cable or a BNC to HD-BNC adapter to connect the
Precision 60 (BNC) to the Codec Pro (HD-BNC).
• Connect the camera control cable (Ethernet) between the camera
control ports on the camera and codec.
Codec: The connector is marked with the camera control symbol.
Camera: Connect to the Ethernet port.
• Connect the power adapter to the camera and connect to power.
• Connect other codec cables as described in theCisco Webex
Room Kit Pro Precision 60 installation guide.
Power
(100-240 VAC, 50/60 Hz)
Power
adapter
Always use the provided power cable
and adapter.
RJ45 HDMI
Contents
Introduction
Physical interface
Connecting to a codec
Appendix
Factory reset
Connecting to a codec

Cisco Quad Camera, Precision 60, SpeakerTrack 60 and PTZ-12 Camera
D15296.10 Cisco Quad Camera, Precision 60, SpeakerTrack 60, and PTZ-12 Camera SEPTEMBER 2019. Copyright © 2019 Cisco Systems, Inc. All rights reserved.
17
Camera guide
Connect Precision 60 to Codec Plus
• Connect the video cable (HDMI) between the camera and codec.
Codec: Always use Connector 1 (HDMI input) for the main camera.
Camera: Connect to the HDMI output.
• Connect the camera control cable (Ethernet) between the camera
control ports on the camera and codec.
Codec: The connector is marked with the camera control symbol.
Camera: Connect to the Ethernet port.
• Connect the power adapter to the camera and connect to power.
• Connect other codec cables as described in theCisco Webex
Room Kit Plus Precision 60 installation guide.
RJ45 HDMI
Power
(100-240 VAC, 50/60 Hz)
Power
adapter
Always use the provided power cable
and adapter.
Contents
Introduction
Physical interface
Connecting to a codec
Appendix
Factory reset
Connecting to a codec

Cisco Quad Camera, Precision 60, SpeakerTrack 60 and PTZ-12 Camera
D15296.10 Cisco Quad Camera, Precision 60, SpeakerTrack 60, and PTZ-12 Camera SEPTEMBER 2019. Copyright © 2019 Cisco Systems, Inc. All rights reserved.
18
Camera guide
Connect Precision 60 to SX80 Codec
• Connect the video cable (HDMI) between the camera and codec.
Codec: Always use Connector 1 (HDMI input) for the main camera.
Camera: Connect to the HDMI output.
• Connect the camera control cable (Ethernet) between the camera
control ports on the camera and codec.
Codec: The connector is marked with the camera control symbol.
Camera: Connect to the Ethernet port.
• Connect a network switch to the codec’s 2nd or 3rd Ethernet port
if you need more than two ports to support your device.
• Connect the power adapter to the camera and connect to power.
• Connect other codec cables as described in theCisco
Telepresence SX80 installation guide.
RJ45 HDMI
Power
(100-240 VAC, 50/60 Hz)
Power
adapter
Always use the provided power cable
and adapter.
Contents
Introduction
Physical interface
Connecting to a codec
Appendix
Factory reset
Connecting to a codec

Cisco Quad Camera, Precision 60, SpeakerTrack 60 and PTZ-12 Camera
D15296.10 Cisco Quad Camera, Precision 60, SpeakerTrack 60, and PTZ-12 Camera SEPTEMBER 2019. Copyright © 2019 Cisco Systems, Inc. All rights reserved.
19
Camera guide
Connect SpeakerTrack 60 to Codec Pro
Power
(100-240 VAC, 50/60 Hz)
Always use the provided power cable
and adapter.
Power
adapter
RJ45 HDMI 2
• Connect the video cables (HDMI).
Left camera: Connect between Connector 1 (HDMI input) on the
codec to the HDMI input of the left camera.
Right camera: Connect between Connector 2 (HDMI input) on the
codec to the HDMI input of the right camera.
• Connect the camera control cable (Ethernet) between the camera
control ports on the camera and codec.
Codec: The connector is marked with the camera control symbol.
Camera: Connect to the Ethernet port.
• Connect the power adapter to the SpeakerTrack 60 connector
panel and connect to power.
• Connect other codec cables as described in theCisco Webex
Codec Pro installation guide.
HDMI 1
Right Left
Contents
Introduction
Physical interface
Connecting to a codec
Appendix
Factory reset
Connecting to a codec

Cisco Quad Camera, Precision 60, SpeakerTrack 60 and PTZ-12 Camera
D15296.10 Cisco Quad Camera, Precision 60, SpeakerTrack 60, and PTZ-12 Camera SEPTEMBER 2019. Copyright © 2019 Cisco Systems, Inc. All rights reserved.
20
Camera guide
Connect SpeakerTrack 60 to SX80 Codec
Power
(100-240 VAC, 50/60 Hz)
Always use the provided power cable
and adapter.
Power
adapter
RJ45
HDMI 1 HDMI 2
• Connect the video cables (HDMI).
Left camera: Connect between Connector 1 (HDMI input) on the
codec to the HDMI input of the left camera.
Right camera: Connect between Connector 2 (HDMI input) on the
codec to the HDMI input of the right camera.
• Connect the camera control cable (Ethernet). Connect between
the codec’s 2nd or 3rd Ethernet port to the Network port
(Ethernet) on the SpeakerTrack 60 connector panel.
• Connect the power adapter to the SpeakerTrack 60 connector
panel and connect to power.
• Connect other codec cables as described in theCisco
Telepresence SX80 installation guide.
Right Left
Contents
Introduction
Physical interface
Connecting to a codec
Appendix
Factory reset
Connecting to a codec