Claybrook BAT-WAT-CAT-FSD-DGY-OTH User manual

1.10.23
Cast Iron Claw Foot Freestanding Bath
If you require any further assistance regarding specification data and technical advice please contact
us at [e-mail]
WATERGATE BATH
Print colours may vary from original.
TECHNICAL INFORMATION
Bath code BAT-WAT-CAT-FSD-DGY-OTH
Size L1370 x w730 x h630-720mm
Body Cast iron painted in Mid-French Grey
Bath feet Painted Soft White
Bathing weight 142.5kg
Tap Holes Only available without
Due to the handmade nature of our products/casting processes, sizing can vary by up to 3%.
First fix should not be undertaken until the product has arrived on site for physical measurements to be taken.

1.10.23
If you require any further assistance regarding specification data and technical advice please contact
us at [e-mail]
WATERGATE BATH
Cast Iron Claw Foot Freestanding Bath
Vitreous Enamel Interior:
A thin layer of glass is fused at high temperatures on to the surface of the cast iron
During the process, the vitreous enamel will follow the contours of the hand cast bath or basin, creating natural undulations within the
surface texture that gives a handmade appearance.
There may be small pin holes in the enamel surface and sometimes minute black specks which all result from the nature of the
manufacturing process and are to be expected.
Care instructions:
Use a solution of soapy water and apply with a soft cloth or sponge in a brushing motion. Do not use wire brushes, steel wool & abrasive
sponge pads. Rinse thoroughly with water immediately after the application of cleaners and wipe the surface leaving it completely dry after
the process.
Do not allow cleaners to sit or soak on the surface and avoid dripping taps.
It is important not to use acidic cleaners or sprays as this will aect the surface of the bath and may result in small brown particles building
up on the enamel surface or staining.
Manufacturers 5 Year Guarantee Terms and Conditions:
This guarantee does not aect your statutory or other legal rights and is subject to the following conditions:
I .The product was purchased from an authorised retailer, within the United Kingdom or Republic of Ireland.
2. The product is used in domestic applications only.
3. The guarantee applies solely to the original purchaser with proof of purchase and therefore is not transferable.
4. The bath must be available to access for the purpose of inspection, maintenance or replacement.
5. Under no circumstances do Claybrook accept liability for any consequential loss or damage arising in the connection with any goods,
material, or service supplied by Claybrook.
6. All products should be installed and maintained in accordance with the instructions provided.
7. Repair under this guarantee does not extend the original expiry date. The guarantee on any replacement parts or product ends at the
original expiry date.
8. Any part found to be defective during the guarantee period will be replaced without charge, providing that the product has been installed
in accordance with the instructions given in this guide and used as the manufacturer intended.
9. If the product is no longer available, we will endeavour to provide the nearest equivalent.
The guarantee does not cover:
I0. Damage or defects caused by - General wear and tear, including special non-chrome finishes, components such as filters, seals, ‘O’ rings
and washers - Incorrect installation - Accidental or wilful misuse - Corrosion and the use of inappropriate cleaning products. - System
debris in eluding the build-up of limescale, which can be controlled through regular servicing and maintenance
I I. Compensation for loss of use of the product or consequential loss of any kind. In the interests of continuous product improvement,
Claybrook reserves the right to alter product specifications with out notice.
12. In the unlikely event that you encounter a problem with your bath, please contact the retailer from whom you purchased the bath.
Claybrook will visit and inspect the bath to advise as to whether it is due to a manufacturing fault or an installation defect. If the problem is
due to a manufacturing fault, they will report back to the manufacturer to arrange further inspection and, if deemed to be a manufacturer’s
defect, a replacement product as soon as possible.

1.7.23
If you require any further assistance regarding specification data and technical advice please contact
us at [e-mail]
WATERGATE BATH
Fitting Instructions

1.7.23
If you require any further assistance regarding specification data and technical advice please contact
us at [e-mail]
WATERGATE BATH
Fitting Instructions