Clean City RCPGG6 User manual

800-231-1327
www.landscapebrands.com
[email protected]
Landscape Brands
211 North Lindbergh Blvd.
St Louis, MO 63141-7809
Phone: [phone]
Fax: [phone]
1 of 4
14.87”
13.25”
14.87”
13.25”
ASSEMBLY INSTRUCTIONS
RCPG6 Recycled Plastic Picnic Table
TOOLS NEEDED:
Ratchet with 9/16” Socket and 3/8” Socket•
Tape•
Level•
2 x
3/8-16 X 1.0”
Carriage Bolt
33 x
3/8-16
Flanged Hex Nut
ASSEMBLY:
The assembly is a two-person operation.
1. Inspect the shipping container contents for damage and to determine that all components and hardware are present.
ASI_RCPG6-B
2. Assemble the Table over the shipping packaging or padded work area to avoid
scratching the product.
Note: Before assembling the Nuts to the Bolts, it is recommended that a light oil or
petroleum jelly be applied to the screw threads
TABLE COMPONENTS:
2 x Table Under
Support
2 x Seat Plank
1 x Center
Brace Mount
2 x Seat Stiffener
Support
1 x
3/8-16 X 1.5”
Carriage Bolt
Washer
Flanged Nut
14.87”
13.25”
3 x Tabletop Plank
ASSEMBLY HARDWARE:
2 x Seat Stiffener 2 x Angle Brace
Carriage Bolt
Tabletop
Plank
30 x
3/8” X 2.5”
Carriage Bolt
4/2011
33 x
3/8” Flat Washer
3. Lay the three Tabletop Planks out on the work
area. The Tabletop Planks can be distinguished
from the Seat Planks because the predrilled holes
on either end of the Tabletop Planks are about
1.5” closer to the end of the Plank.
Push a 2.5” long Carriage Bolt through each of the
holes in each of the Tabletop Planks.
Note: It may be helpful to Tape the Bolt heads in place
so the Planks can be adjusted without dislodging
the Bolts.
4. Place one of the Table Under Supports over one of
the lines of Carriage Bolts. Make sure the vertical
ange on the mounting bar of the Under Support
faces outward toward the nearest end of the
table. Place a Flat Washer and Flanged Nut on the
Vertical ange
oriented out
toward nearest
end of the Table
end of each Carriage Bolt and tighten. Repeat for the other Under Support. Be sure to check the alignment of the vertical ange
on the mounting bar before tightening the Flanged Nuts.

2 of 4
6. Place the mounting hole of one of the Angle Braces over the Carriage Bolt in the middle of the Center Brace Mount. Align the
hole on the other end of the Brace with the hole in the Mounting Plate on the Under Support. Place a Carriage Bolt through the
Mounting Plate and Angle Brace and then add a Flat Washer and Flanged Nut to the end of the Carriage Bolt. Leave the hardware
nger tight so the Tabletop can be adjusted and leveled later.
5. Place the 1.5” Carriage Bolt through the hole in the center of the Center Brace Mount and hold (or tape) it in place and position
the Center Brace Mount over the line of Bolts across the center of the Tabletop. Add a Washer and Flanged Nut to each of the
Carriage Bolts, except the center one, and tighten them using the Ratchet and 9/16” Socket.
1.5” long
Carriage Bolt
2.5” Long
Carriage Bolt
Flanged Nut
Angle Brace
Mounting Plate on
the Under Support
Tabletop Plank
Center
Brace Mount
Flanged Nut
Flat Washer
Carriage Bolt
Flat Washer

3 of 4
7. Repeat Step 6 for the Angle Brace and Under Support at the other end of the Table.
After both Braces have been attached to the Center Brace Mount, add a Flat Washer and Flanged Nut to the end of the Carriage
Bolt. Leave the hardware nger tight so the Tabletop can be adjusted and leveled later.
Flat Washer
Flanged Nut
Carriage Bolt
Angle Brace
Angle
Brace
Angle Braces
Apply hardware
to outer Bolt only
Seat Stiffener
Support
Note:
Only add hardware to one
of the Carriage Bolts.
Note orientation of
Seat Stiffener Support
8. Place one of the Seat Stiffener Supports over the two carriage bolts in the center of one of the Seat Planks. Add a Flat Washer
and Flanged Nut to one of the Carriage Bolts and tighten with the Wrench and Socket. Repeat this step for the other Seat Plank.
Center Brace
Mount
Center Brace
Mount
9. Raise one of the Seat Planks up to the Seat Mounting Bracket on one of the Under Supports. Orient the Seat Plank so that the
Nut and Washer on the Seat Stiffener Support is toward the outside edge. Add a Washer and Nut to the Carriage Bolt through the
Seat Bracket on the outside edge of the Seat Plank. Leave the hardware nger tight until the Seat Stiffener is attached.
Place the Seat Stiffener over the three Carriage Bolts on the inside edge of the Seat Plank and add a Washer and Nut to each of
the Carriage Bolts. Tighten all of the Seat hardware.
Seat Stiffener
Carriage Bolts
taped in place

CARE AND MAINTENANCE
Do not drag the assembled unit across any surface.•
This product requires only periodic cleaning with a sponge and a solution of mild detergent and water to remove surface dirt.•
Do not clean with a solvent or petroleum based products.
WARNING
Furniture must not be used other than for its intended purpose and should be inspected regularly for loose, missing, or broken•
hardware, and general instability.
Furniture that is damaged or appears to be unstable must be removed from service and be repaired or replaced.•
Repairs must be made using only factory authorized parts and methods.•
Attach the second Seat Plank by
repeating Step 9 for the second
Plank.
10. Repeat Step 9 to attach the other Seat Plank to the Table Under Support.
12. Turn the Table right side up and tighten all hardware while checking with a Level.