Hanover MONDN3PCSWBR User manual

HanoverOutdoorFurniture
IMPORTANT
Ifyouhaveanyproblemswiththisproduct(missingordamagedparts,assemblyissues,etc.),
PLEASEDONOTRETURNTOTHERETAILER/STORE
fromwhereyoupurchasedtheproduct.
PleasecallourToll‐FreeCustomerServiceHotlineat:1‐800‐416‐3511
Between9:00AMand5:00PMEasternTime,MondaythroughFriday
Orvisitourwebsiteat:www.hanover‐products.com
Toexpediteanyfuturewarrantyclaims,pleaseretaintheInstructionSheet,Warranty
Cardandreceiptforfutureuse.
For additionalon‐linesupportonassembly,troubleshootingandcare&maintenanceofyouroutdoor
furniture,pleasevisitourwebsiteat:www.hanover‐products.com.
6/1/2015(a)

ASSEMBLY INSTRUCTIONS
1
FOOT CAP
SWIVEL PLATE
"U" BAR
C
G
I
D
E
H
F
A
B
Position the swivel base on a flat, solid surface. Make sure the swivel plate is positioned all the way into
the base. It may have vibrated out during shipment. The two sets of holes in the swivel plate should be
facing away from you.
Note the arrows on both the swivel plate and the "U" bar portion of the chair frame. Position the chair frame
ontotheswivelplatesothatthetwopairsofholesinthe"U"barareexactlyalignedwiththetwopairsof
holes in the swivel plate and the arrows on both the "U" bar and swivel plate are pointing in the same
direction. Proper positioning of the chair frame on the swivel plate/swivel base assembly, and proper
alignment of the holes in the "U" bar with the holes in the swivel plate are critical to the safe, well balanced
swiveling motion of the chair.
Carefully examine the diagram. Attach a metal plate to two (2) bolts and guide the bolts through the top of
one set of holes in the "U" bar (located at the bottom of the chair frame) and into the pair of holes in the
swivel plate. From beneath the swivel plate, add a washer, then a spring washer and a nut to the end each bolt.
Hand tighten 3-4 revolutions only. Repeat procedure for pair of holes on the opposite side. Again, hand
tighten nuts 3-4 revolutions only. Do not tighten nuts completely.
Using the hex wrenches provided, tighten the nuts and bolts. Be sure the bolts are fully tightened. Remove
arrow labels from the “U” bar and swivel plate. Cover bolts and nuts with covers. Your chair is now ready
for use.
2
3

*NOTE:PARTSSHOWNONPARTSLISTARENOTTOSCALE
PARTS IDENTIFICATION LIST
SWIVEL
ASSEMBLY
& BASE
FC0030
FOOTREST COVER
FACTORY ASSEMBLY G0304
FOOT CAP
FACTORY ASSEMBLY
HEX WRENCH-1 HW0008 1
HEX WRENCH-2 HW0007 1
BOLT COVER HW0028 4
QTY
5/16" X 43 MM
BOLT
Ø8.0 X 2.3 MM
SPRING WASHER HW0003
5/16" NUT HW0015
METAL PLATE
CHAIR FRAME
PARTS LIST DESCRIPTION ORDER PART #
2
4
4
4
1
1
HW0450
A
B
C
D
E
F
G
H
I
J
K
HW0686
4
Ø85X15MM
WASHER
.. HW0005
4
HW0109
AB1267
AB1268
NUT COVER

ASSEMBLY INSTRUCTIONS
1
2
Attach a table leg to the leg connector bracket by using two 1/4"x30 mm bolts and Ø6.5x1.0 mm washers as
shown in . Guide the bolts through holes in leg connector brackets into pre-drilled holes in the legs.
Repeat for other three table legs.
Fig 1 Hand
tighten only.
Place the table top upside down on a flat, non-abrasive surface. a table leg
ig.2
Attach to the table top by using two
1/4"x35 mm bolts and Ø20xØ6.5x2.0 mm washers as shown in . Guide the bolts through the holes in the table
leg into the pre-drilled hole in the table top. Repeat for the other table legs.
F
Hand tighten only.
B
FOOT CAP
C
H
D
F
A
H
E
G
3After making any necessary adjustments to the alignment of the table, use the hex bolt driver and hex wrench to
tighten all bolts . each bolt must be tightened a few revolutions at a time. In order to apply equal pressure
to all bolt joints, we recommend working in a cross corner (X fashion). Repeat until all bolts are tight.
Over tightening may strip bolts. Cover all bolts with covers.
Note:
Do not
over tighten.

*NOTE:PARTSSHOWNONPARTSLISTARENOTTOSCALE
PARTS IDENTIFICATION LIST
PARTS LIST DESCRIPTION ORDER PART # QTY
A
B
C
D
E
F
G
H
I
J
LEG CONNECTOR
BRACKET
TABLE LEG 4
1/4" X 35 MM BOLT
8
1/4" X 30 MM BOLT HW0038
1
Ø6.5 X 1.0 MM
WASHER HW0004
HW0105
BOLT COVER
HEX BOLT DRIVER 1
HW0006
FOOT CAP
FACTORY ASSEMBLY FC0069
TABLE TOP
1
8
HW0142
8
TOUCH-UP PAINT G0003 1
16
Ø20XØ 26.5 X .0 MM
WASHER HW0594 8
AT52583
AT52584
AT52585