Clear-Com FSII-BASE-II User manual

ECLIPSE HX VERSION 8.5.0 Rev A RELEASE NOTE
FSII-BASE-II
v1.2
RELEASE NOTE
Date: 25th October 2016
Release: v1.2
Doc Part No: 399G171 Rev D
Release
Note

FSII-BASE-II v1.2 Release Note Page 2 of 5
This Document Part No. 399G171 Rev D
CONTENTS
1INTRODUCTION ................................................................................................................... 3
1.1 Scope .......................................................................................................................................3
1.2 v1.2 ..........................................................................................................................................3
1.3 v1.1 ..........................................................................................................................................3
1.4 v1.0 –First Release..................................................................................................................3
2FIRMWARE COMPONENTS ................................................................................................... 4
2.1 Firmware..................................................................................................................................4
2.2 Documentation........................................................................................................................4
3KNOWN ISSUES.................................................................................................................... 5

FSII-BASE-II v1.2 Release Note Page 3 of 5
This Document Part No. 399G171 Rev D
1Introduction
1.1 Scope
This document describes the release of the FSII-BASE-II product family
1.2 v1.2
Issues addressed in this release
Beltpack input/output gain not properly re-applied after beltpack power cycle
Audio level overridden when applying change to role
MV] shown on keyset even if only one role is selected
Stuck cross-point when removing yourself from a group
Log file over-run fixed
FSII-BASE-II USB - If I plug in an already registered beltpack it disconnects and may connect to a
different system on power cycle
Unable to press/unpress talk/call when in front panel menu
1.3 v1.1
Reason for change from v1.0 to v1.1
Beltpacks continued to receive audio from the 4W interface after deleting the role.
1.4 v1.0 –First Release
FSII-BASE-II product Family
FSII-BASE-II
FreeSpeak II Digital license-free wireless base station with XLR-4M headset connector. Supports
up to 25 Beltpacks and 10 antennas. (Two antennas can connect to the base station directly or up
to 10 antennas can be connected by using two x PD2203 splitters) The base station has
connections for four 2-wire party-lines (CC or RTS) with auto nulling, and four 4-wires plus a
dedicated SA output and dedicated program audio input, along with 4 relays.
FSII-BASE-II-X5
FreeSpeak II Digital license-free wireless base station with XLR-5F headset connector. Supports up
to 25 Beltpacks and 10 antennas. (Two antennas can connect to the base station directly or up to
10 antennas can be connected by using two x PD2203 splitters) The base station has connections
for four 2-wire party-lines (CC or RTS) with auto nulling, and four 4-wires plus a dedicated SA
output and dedicated program audio input, along with 4 relays.

FSII-BASE-II v1.2 Release Note
FSII-BASE-II v1.2 Release Note Page 4 of 5
This Document Part No. 399G171 Rev D
2Firmware Components
2.1 Firmware
Part No in
previous
releases
(Historic)
Part No
Description
File Type
Production
Rev
Dev Issue
Last updated in
Release
780G034
FSII-BASE-II Application Code
Ext3.gz
D
1.0.12.3
v1.2
2.2 Documentation
Part No in
previous
releases
(Historic)
Part No
Description
Production
Rev
Doc Issue
Last updated in
Release
399G168
FSII-BASE-II Quick Start Guide
B
B
v1.0
399G169
FSII-BASE-II Instruction Manual
B
B
v1.1
399G171
FSII-BASE-II Release Note
D
D
v1.2
399G172
FSII-BASE-II Passcode Customer Letter Template
A
A
v1.0

FSII-BASE-II v1.2 Release Note
FSII-BASE-II v1.2 Release Note Page 5 of 5
This Document Part No. 399G171 Rev D
3Known Issues
This section details those issues that contradict the relevant manuals included in this release. These
issues have not been resolved and are listed here to help you use the system more effectively.
Front panel menu has 'disabled' for forced listen key type in latch area
Brightness display settings under general settings of a role is different to that of the beltpack
Reply Key text on belt pack disappears mid-call when making live updates
No message on the front panel when updating from CCM
Turning the Belt Pack rotary volume (A clockwise, B anticlockwise) at the same time will not
update the volume
Chinese characters do not display on Front Panel
A Re-Registered Beltpack jumps to its old associated role
You can't scroll up and down the Roles menu using up & down arrows or Page Up & Down
When display brightness is set to “Very Low” (the lowest setting, currently) then “Display Dim
Timeout” acts as “Display Off Timeout” instead, while “Display Off Timeout” doesn’t do
anything regardless of the time chosen
Pops heard on the 4Ws and 2Ws when changing between Electric and Dynamic.
You cannot modify system ID on the Base Station
Newly connected antennas goes to the bottom of the list until you come out and re-enter the
monitoring screen
Setting a fixed role from the Front Panel, the beltpack hangs in the connecting state
Power sense stays on when it should be off
Cloning preconfigured role is broken as the cloned role has different key assignment
Beltpack Master Volume adjustment is not consistent on the FSII-1.9 beltpack
Antenna Resets/Frozen after base station Reset or in heavily loaded system
While a beltpack was is receiving a call signal from a channel, unassigned the channel from the
beltpack key and the call key remain inverted till a beltpack reboot