Clear-Com FreeSpeak II User manual

FreeSpeak
II®
Transceiver/antenna splitter
Transceiver/antenna splitter
The FSII-SPL transceiver/antenna splitter is a device that connects multiple transceiver/antennas to an
Eclipse matrix (E-Que HX card) or Freespeak 11 Base Station. It has a matrix RJ 45 connector
that carries
the data between an E-Que card transceiver port and the splitter, and five antenna RJ-45 connectors to feed
that information to and from up to five antennas. The splitter must be locally powered using the supplied
external in-line universal power
supply.
In addition, the FSII SPL provides fiber linking to a FSII-Base-II Base Station and another FSII~SPL unit.
There are eight DIP switches to select the mode of operation, and to enable Local DECT
synchronization and
software updates.
You can mount the splitter on a flat surface or on a microphone stand using the screw points or stand
connectors.
The FSII-SPL is compatible with both FSBP (Freespeak I) and FSII-BP (Freespeak II, 1.9 &
2.4) systems.
FSII-SPL
front connector panel
Antenna Connection LEDs
Connection medium LEDs
1 2 3 4 5 RJ45 Fiber Power
Anienna Connection Ease Connection
Freespeak ll "‘
FSII-SPL Front Connector Panel
Antenna Connection LEDs
These yellow LEDs indicate that the splitter is receiving data from the antennas.
Base Connection LEDs
Connection to Base; RJ45 or fiber.
- If the LEDs are steady on, DECT
synchronization is being received from the Base Station/matrix.
. lf the LEDs display a double flash, DECT
synchronization is occurring locally.
. lf the LEDs display a rapid pulse flash, there is no DECF
synchronization (fault condition).
Power LED
This green LED indicates that the splitter is receiving power.
Page 1 3996182 Rev A April 6, 2016
|
H"
«
m
iiitclear-cnmi*

FSII SPL rear panel
i-‘iber RJ45 Antenna Connections
C°""€Ctl°" connection
to Base/ to Base/
DC po er splitter matrix
rreespeak ll
FSII-SPL Rear Connector Panel
DC IN po er connector
This connector is used to locally po er the splitter ith the supplied universal po er
supply. Use of local
po er is required.
Fiber connection to Base
Station or another
FSII-SPL unit
This connector
uses a Fiber Module (Part# HCI-SMFO
or HCI-MMFO)
RJ45 connection to Base Station or matrix
One EtherCON RJ-45 connector
Antenna connectors
Five EtherCON RJ-45 connectors
Connecting and using a splitter
Connect the FSII-SPL base connector to matrix E-Que (RJ45 connection) or Base Station antenna port (can
be RJ45 or
fiber). Connect all antennas (up to 5) to splitter antenna ports. Also make sure that the both the
po er LED (green for 1.9 GHZ, blue for 2.4 GHZ) and the yello data LED are lit on each antenna. If all are
properly lit, then the connection has been successfully made
and the coverage zones ill be active and ill
support beltpacks. If the transceiver antennas
are not lit, check the connections.
Note: Cable distances under 300m (985 feet), antennas can be po ered by
the splitter. Above 300m
they
must have direct/local po er.
Make
any necessary DIP s itch settings (mode of operation, local DECT
synchronization, firm are update).
DIP s itch settings {default in BOLD]
1 to 5 Antenna ports 1 to 5 To access the DIP
s itches, remove
0"
- Acme
_ the covering panel on the base of the
OFF
' C°”Ve't '5° F'be" splitter (t o scre s).
6 ON
— Base Sync
OFF
— Local Sync Note: hen
you change a DIP
7 If 6 is s itched t° OFF s itch setting, you must
re-
ON
— Freespeak II po er the unit for the change to
opp
- F.-eespeak I have
any
effect.
8 ON
— Update
OFF
- Normal operation
Page 2 399G182 Rev A April 6, 2016
lllllt clear-cum“

~~~
Typical FSII-Base/FSII-splitter 1
configurations using Clear-Com
equipment
Matrix
~
E1/ FIBER LINK
DIP 1 to 5 — ON
DIP 1 to 5 OFF (DEFAULT) ~~~
~
FSII-Base
Station
~~
~ ~
~
FIBER LINK ~~
DIP 1.2 - ON DIP 1 to 5 — ON
DIP 3 to 5 OFF (DEFAULT)
FIBER LINK
DIP 1 to 5 — ON
(DEFAULT)
Typical system
confi uration
using third party
equipment
Note: In this configuration, there is no DECT
Synchronization
from
the Base Station or matrix (DIP 6 — OFF). Only local DECT
synchronization is possible. ~
~~~
SET SPLITTER TO LOCAL
El TO FIBER CONVERTOR 5"“: "'°°E
FIBER LINK .l——- ~---
~
El
Copyright ©
2016 HME
C|ear—Com Ltd. All rights reserved.
Page 3 399G182 Rev A April 6, 2016
~I|llilEI:Iear-com“