ClearView 834IP71 User manual

Mini
IP
Dome Camera
Version 1.1.0

Thank you for purchasing our IP camera!
This quick start guide
is designed to be a reference tool for your system.
Please keep this start guide well for future reference.
Please open the
accessory bag to check the items one by one in
accordance with the list below.
Contact your local retailer ASAP if something is missing or damaged
in the bag.
1. Electrical safety
All installation and operation here should conform to your local
electrical safety codes.
The power shall conform to the requirement
in the SELV (Safety
Extra Low Voltage) and the Limited power source
is rated 12V
DC in the IEC60950-1.
We assume no liability or responsibility for all the fires or electrical
shock caused by improper handling or installation.
We are not liable for any problems caused by unauthorized
modification or attempted repair.
2. Transportation security
Heavy stress, violent vibration or water splash are not allowed
during transportation, storage and installation.
3. Installation
Do not apply power to the camera before completing installation.
Please install the proper power
cut-off device during the installation
connection.
Always follow the instruction guide the manufacturer recommended.
Quick Start Guide
01

Mini
IP Dome Camera
4. Qualified engineers needed
All
the examination and repair work should be done by the qualified
service engineers.
We
are not liable for any problems caused by unauthorized
modifications or attempted repair.
5.
Environment
This series
IP
camera should be installed
in
a cool, dry place away
from direct sunlight, inflammable, explosive substances and etc.
Please keep
it
away from the electromagnetic radiation object and
environment.
Please make sure the CCD (CMOS) component
is
out
of
the
radiation
of the laser beam device. Otherwise
it
may result
in
CCD (CMOS)
optical component damage.
Please keep the sound ventilation.
Do
not allow the water and other liquid falling into the camera.
Thunder-proof device
is
recommended to be adopted to better
prevent thunder.
The grounding holes of the product are recommended
to
be
grounded to further enhance the reliability of the camera.
6.
Daily Maintenance
Please shut down the device and then unplug the power cable
before you begin daily maintenance work.
Do
not touch the CCD (CMOS) optic component.
You
can use
the blower to clean the dust on the lens surface.
Always use the dry soft cloth to clean the device.
If
there
is
too
much dust, please use the water to dilute the mild detergent first
and then use
it
to clean the device. Finally use the dry cloth
to
clean
the device.
Please put the dustproof cap to protect the CCD (CMOS)
component when you do not use the camera.
7.
Accessories
Be
sure to use all the accessories recommended by manufacturer.
Before installation, please open the package and check
all
the
components are included.
Contact your local retailer ASAP
if
something
is
broken
in
your
package.
Mini IP Dome Camera
02

Quick Start Guide
Accessory
Name
Amount
IPC
Unit 1
Accessories bag 1
Quick Start Guide 1
CD 1
Quick
Start
Guide
03

Mini IP Dome Camera
1
Framework
..................................................................................
05
1.1
Dimensions.......
..
..
....
..
...
..............
..
..
.......
..
......
.. ..
......
..
...................
..
........05
1.2 Structure.
..
.
..
..............
..
.....................
..
.......
..
...
......
.. ..
.....
....
...
...................
06
2
Installation
..................................................................................
08
2.1
Device Installation.
...
.
...
...........................................................................08
2.2
SO
Card Installation
...
...............
...
..........
..
..
...
..
.....
..
...............
.. ..
.............. 1
0
3
Quick
Configuration
Tool..
.........................................................12
3.1 Overview
..
....
........
... ...
.......
..
...................
..
........
..
...........
..
.
..
....
.......
...
.. ..
...
12
3.2 Operation
...
.........
...
..........................................
...
..
..
.............
..
.
...
..
...
.
..
..
...
12
4
Web
Operation
............................................................................15
4.1
Network Connection................
..
....
.....................
..
..............................
..
.
..
15
4.2 Login and Logout........
...
.. .. ..
..........................
..
....
..
..
...
..
..
.....................
..
.
15
Appendix
Toxic
or
Hazardous
Materials
or
Elements
................19
Mini IP D
ome
Camera
04

1.1 Dimensions
Please refer to the following figure for the dimension information. The unit is mm.
See Figure 1-1 through Figure 1-3.
Figure 1-1
Rl. 75 R2.6
Figure 1-2
Quick Start Guide
05

Figure
1-3
1.2
Structure
Please refer to the following figure for detailed information. See Figure
1-4.
Figure
1-4
Mini
IP
Dome
Camera
06
CD
®
®
@

Quick Start Guide
--
-- --
---
-
--
·-
Please refer to the following sheet for detailed information.
SN
Name
,,
1
X-
Y
-Z
rotation module
2 Device lens
3
Dome camera enclosure
SN
Name Function
4 Power input port Connect to the
DC
+
12 power to input the power.
5
Network port Network data input, output and
PoE
.
Quick
Start
Guide
07

Mini
IP Dome Camera
2.1 Device Installation
This series
IPC
can be put
on
the table to realize surveillance.
Or
you can use
the bracket or the
in-ceiling
installation to realize the hang function. Please
refer to the steps listed below.
Dome camera body
.u.-
--
---
- -
--
Enclosure secure screws
Figure
2-1
lnnerhexagona~
---~~~~~~
~~
wrench Figure
2-2
Mini IP D
ome
Camera
08

· Quick Start Guide
~tep_1
Use the inner hexagonal wrench (provided) to loose the three inner hexagon
screws
in
the dome cover and then open the cover.
Step 2
Please take the installation position map
in
the accessories bag, and then
paste
it
on the ceiling or the wall according
to
your monitor area requirements.
Draw and then dig three plastic expansion bolts holes
in
the installation
surface and then insert three expansion bolts
in
the holes. Secure these three
bolts firmly. Please dig a
"cable
exit hole"
in
the surface according to the
installation position map
if
you want
to
draw out the cable from the top of the
installation surface.
You
need to use the proper tool to open up the side port of
the
U-cable
channel of the dome camera pedestal
if
you want to draw out the
cable from the side port of the cable channel when you are installing the
device cable. And then you can draw out the cable from the cable channel of
the pedestal.
St~
Adjust the dev1ce installation pedestal to the proper position and then draw the
cable through the cable exit you just dug
in
the ceiling (wall). Line up the TOP
direction of the device to the installation position map and then line up the
three screw holes
in
the device pedestal to the three plastic expansion bolt
holes
in
the installation position. Put the three
self-tapping
screws
in
the three
plastic expansion bolts firmly. Now the dome camera
is
secure
in
the
installation surface.
Step 4
Loosen the two M3 secure screws of the lens rotation structure (Do not remove,
loosen a !ittle bit will be OK.). Use the inner hexagonal wrench to insert them to
the inner hexagonal holes and then use the wrench to turn the lens. Adjust the
lens to the proper monitor angle and then secure
Hie
screws of the lens
rotation structure. The lens adjust angle ranges are: flip (0°
~+
75
° ),video
pan rotation
(-15
°
~
+15
°
) , video rotation
angle(-15
°
~+15
°
).
Quick
Start
Guide
09

Step 5
Line up the dome camera cover
to
the cable exits and put the cover back.
Use the inner hexagonal wrench to secure the three inner hexagonal screws
firmly. Now the installation completed.
Note:
The
device GND cable can effectively enhance the device reliability. The
GNO
hole
is
near the cable exit of the back of the enclosure.
The
GND screw
specification
is
M3.
See
Figure
2-3
.
2.2
SO
Card Installation
Important
0
Figure
2-3
Some series product do not support the
SO
card storage function.
Please shut down the power and then turn off the device before you install the
SO
card.
Step 1
Please refer
to
the step 1
in
chapter 2.1
to
open the device.
Step 2
Find the "SO CARD" indicator
in
the enclosure. Adjust the
SO
card
to
the
proper direction and then install.
See
Figure
2-4.
Step 3
Please refer
to
the step 5
in
chapter
2.1
to complete the installation.
Mini IP
Dome
Camera
10

. Quick Start Guide
Figure
2-4
Quick
Start
Guide
11

Mini IP Dome Camera
3.1
Overview
Quick configuration tool can search current
IP
address, modify
IP
address.
At
the same time, you can use
it
to upgrade the device.
Please note the tool only applies to the
IP
addresses
in
the same segment.
3.2 Operation
Double click the "ConfigToois.exe" icon, you can see an interface
is
shown
as
in
Figure
3-1
.
In
the device list interface, you can view device
IP
address, port number, subnet
mask, default gateway, MAC address and etc.
l
li
•n«
:..i:+.
I
::H
-
-"·
n·
.
~
·
i~
~,~
..
I'
~~~~
!~-~
~~r
~~~~~~
~~~~~1M~~~
~~~
~~
~~~~~~~~
:
~
~~
I
f..
!
·:<
~
l·~·
·ji
-" • '
i
1
~: ;
~"-:'~\ii
i
!<)
;
'
'""
;-.~~
~~~
::•
f,
~
;
,1
;,..,
,,
.
.,,
:
n•
:>·:
k'
.t
·n
j,,
,
.·
•.h ,
,-
,
,_;
1
•
.h
·
c.r
~
~L
..
r
l
l~
<.!
i
t:~
::;.
_
p
·.~
r
,
·b;~
i£
;.n
f
l~
·
!
•
J.I
;.f.
~
.
~
1
.::
'-
•• .
:,
1
•
~
.:;~
::
t'Y·
:t/i
I!' "
C
l
Figure
3-1
OCr
']
1.
r:,
]..
~
:·;
~i
.~
l
,
tY!
~
~
;t;.:
~;
-
J
l
·~
'·~i
f
i
1;
Select one
IP
address and then right click mouse, you can see
an
interface
is
shown as
in
Figure
3-2.
Mini
IP
Dome
Camera
-
--
-
--
12

Quick Start Guide
ConfisTool
- .
IJl
SN
IF
A<i~irft:i.t
w
~
"·
r
!C .,
t:
:.:-
!
!(
'
J
!0
1
0
~
10 7
.:::
::.
.!
I I •
~
';l,
:
2S:
-
'
.~
f)
(I
j l_'
7 (' l
)
IT
;
··
~-':,
~
-
:2'~
'
.::
U
ti
3
77;~
:·
-:s
::
:-
t;:
.
o.
o
M_•e
~Jdnu
:
.
~
51
_-
•
1,(
ff
sc
5.:1
~
.
:_:-
.:_;
-
~
'i·:
f.j
~·b
~".\
t:·.
::
s
~
:t
.:
f.J
'./ J
~
:
1
00 ·:
15
;::
:
16
:
'
~
·
~f:;
lt
7 1
i i "·,
'
;77'7'7
:.:
S
1
.~
;:
r;:·
t:
,
i)
0
1
·.
·;~
7
C:
C:<'
:
5
~
'~·.:
fi£
·;;~
:
37
t/
~~-~~-'f;h
~
?
~
~
~
J:~~~-
·
e::iiiJ.ttJIII.
~~~~
f!!;S~if&:llrr
·
-
~
~
- -
··
;;
:
·
;~-~;:;~_:
~
p~~
:
·
~~~
-
··-
..
--~
-~*
~~J!.;R,.,_
1
C·
-·
.: t
):
<
?/"'"
·
~
c
1::
-
~
-~
-
J
~
·::
p
_•·
·r
P
1
ur
.•
t.r:f'
:nJ
i:i
d.
I
I
~
t
~1
1
•
··
1
1
C
5
.~
d1
-
~
k
'' l
·:
·t J
r;
"
f-
1!
":~
-:
-r.
-
i
;
rr
:·
~
..
f
lj
,'*t' n q
·•
.t
1
r-r~:-.
~
1•-·
h·L
:-.:
4.
l
t.
L ·t
rn
;_
;.
f l
-.
!n
h'
Figure
3-2
Select the "Open Device Web" item; you can go
to
the corresponding web
login interface. See Figure
3-3
.
Figure
3-3
Quick
Start
Guide
13

Mini
IP Dome Camera
If
you
want to modify the device
IP
address without logging
in
the device web
interface, you can go to the configuration tool main interface to set.
In
the configuration tool search interface (Figure
3-1
),
please select a device
IP
address and then double click
it
to open the login interface. Or you can
select
an
IP
address and then click the Login button to go
to
the login interface.
See
Figure
3-4.
In
Figure
3-4,
you can view device
IP
address, user name, password and port.
Please modify the corresponding information to login.
Please note the port information here shall be identical with the port value you
set
in
TCP
port
in
Web Network interface. Otherwise, you can not login the device.
If
you
are use device background upgrade port 3800 to login, other setups are
all
invalid.
IF
HJ
...
u
10
. 10 . ] . l
li
Figure
3-4
After you logged
in,
the configuration tool main interface
is
shown as below.
See
Figure
3-5.
tttiJJ.
Figure
3-5
Mini
IP
Dome Camera
14

, Quick,Start Guide
For detailed information and operation instruction ofthe quick configuration
tool, please refer to the Quick Configuration Tool User' s Manual included
in
the resources CD.
This series
IPC
product support the Web access and management via
PC
.
Web includes several modul
es:
monitor channel preview,
PTZ
control,
system configuration, alarm and etc.
4.1
Network
Connection
Please follow the steps listed below for network connection.
• Make sure the
IPC
has connected to the network properly.
• Please set the
IP
address, subnet mask and gateway of the
PC
and the
IPC
respectively.
IPC
default
IP
address
is
192.168.1 .1
08.
Subnet mask
is
255.255.255.0. Gateway
is
192.168.1.1.
• Use order ping
***.***.***.***(*
IP
camera address) to check connection
is
OK
or not.
4.2 Login and Logout
Open
IE
and input
IP
camera address
in
the address bar.
For
example,
if
your camera
IP
is
192.168.1.108, then please input http://
192.168.1.108
in
IE
address bar.
See
Figure
4-1
.
Quick
Start
Guide
15

Mini
IP Dome Camera
....
Figure
4-1
The
login interface
is
shown
as
below. See Figure
4-2
.
Please input your user name and password.
Default factory name
is
admin and password
is
admin.
Input your
IP
address here
Note:
For
security reasons, please modify your password after you first login.
!
~
~
t
rtt
):
~e"
"'
F
~~orll:e
s
!"'*-'
t;e"'
~
;
Figure
4-2
Min1
IP
Dome Came
ra
16

Quick Start Guide
If
it
is
your first time to login
in,
system pops up warning information to ask you
whether install control webrec.cab or not after you logged
in
for one minute.
Please click OK button, system can automatically install the control. When
system
is
upgrading,
it
can overwrite the previous Web too.
If
you can' t download the ActiveX file, please check whether
you
have installed
the
plug-in
to disable the control download. Or you can lower the
IE
security
level.
See
Figure
4-3.
Security Settincs -Inte-rnet Zone
~
Gener
al
SecLrity Privacy
Cortent
Connect
bns
Prol}"ams ; Ad¥anced
'3-
f.H:ir
"~~
)
"i
-
i!j
~
Internet L
oco
ltltronet Trusted sites v
Internet
Th>
zone
Is
for Internet
webSitcs
,
except trnse l
osted
n t
rusted
ond
r
e
~t
r
l
c
tecf
zones
Allwed l
evels
for
th>
zcno:
Medum
to
HIQh
MediUm-t.gh
,
.J
·
App
r
opn~e:
for most
webs.~tes
·Prompts before
do
wnOadwl\l
pcJtert•aly
cmaf
e
content
• U
nsq,ed
Ac
t•veX
coot
rols
"''rd.
be
OO..nloocie
d
"
:·:·,
Disable
(: i
Enoble
# Download
siQned
ActiveX control>
(rd.
secure)
·-
::)
Olseble
·:!1
Enable
(
rd.
secure)
() Prompt (recommended)
•
if
Downlolld
unsiQned
Acti•eX
controls
(not
secure)
-.n
Disable
(recommended)
:
:
~)
Eneble (
rd.
serure)
() Prompt
,
<#
ln•t>!!t>e
end strlpt ActNeX cortrols
not
marked '""
we
for
So
(!
Disable
(recommended)
(.)
Enoble
(not
<erure)
0 P
ro
l'rflt
#
Run
Acti•eXcootrols
an
d
plug·>n<
( "\
~o.-.,.....;,..,ir+
~
·
~
,.,.
................
...
1"'1
·
r~
effect after you restart Internet
El<plorer
v
R~:,>et
...
Figure
4-3
Quick
Start
Guide
17

Mini IP Dome Camera
After you logged
in,
you can see the main window. See Figure
4-4.
Se-'!C
r,
F.!!
VOr
lt
es
·
~'
Figure
4-4
Please refer
to
the Web Operation Manual included
in
the resource CD for detailed
operation instruction.
Mini IP Dome Camera
18

Quick Start Guide
Appendix Toxic or Hazardous Materials or Elements
Component
Toxic or Hazardous Materials or Elements
Name
Pb
Hg Cd
CrVI PBS
PBDE
Circuit Board Component 0 0 0 0 0 0
Device Construction 0 0
Material 0 0 0 0
Wire and Cable 0 0 0 0 0 0
Packing Components 0 0 0 0 0 0
Accessories 0 0 0 0 0 0
0: Indicates that the concentration of the hazardous substance in all homogeneous
materials
in the parts is below the relevant threshold of the SJ!T11363-2006
standard.
X: Indicates that the concentration of the hazardous substance of at least one
of all homogeneous materials
in the parts is above the relevant threshold of
the SJ!T11363-2006 standard. During the environmental-friendly use period
(EFUP) period, the toxic or hazardous substance or elements contained
in
products will not leak or mutate so that the use of these (substances or elements)
will not result in any severe environmental pollution, any bodily injury or damage
to any assets. The
consumer is not authorized to process such kind of
substances or elements, please return to the corresponding local authorities
to process according to your local government statutes
Quick Start Guide
19