ClearView HD2-B27-M User manual

HDAVS Motorized Vari-focal IR Waterproof Fixed Camera
User’s Manual
Version 1.0.0

i
Table of Contents
1General Introduction ..................................................................................................................1
1.1 Overview........................................................................................................................1
1.2 Features.........................................................................................................................1
2Device Framework .....................................................................................................................2
2.1 Framework and Dimension.........................................................................................2
2.2 Structure Component...................................................................................................2
2.3 Lens Zoom Adjustment ...............................................................................................3
3Installation....................................................................................................................................4
4Menu.............................................................................................................................................6
4.1 HDAVSLocal Settings..................................................................................................6
4.1.1 Control Coaxial Device...................................................................................................6
4.1.2 Set Audio Coax................................................................................................................6
4.1.3 Open Menu.......................................................................................................................7
4.2 Menu List .......................................................................................................................8
Appendix Toxic or Hazardous Materials or Elements ...............................................................12

ii
Welcome
Thank you for purchasing our HDAVS camera!
This user’s manual is designed to be a reference tool for your system.
Please read the following safeguard and warnings carefully before you use this series product!
Please keep this user’s manual well for future reference!

iii
Important Safeguards and Warnings
1．Electrical safety
All installation and operation here should conform to your local electrical safety codes.
The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited
power source is rated 12V DC in the IEC60950-1.
We assume no liability or responsibility for all the fires or electrical shock caused by improper handling
or installation.
2．Transportation security
Heavy stress, violent vibration or water splash are not allowed during transportation, storage and
installation.
3．Installation
Do not apply power to the camera before completing installation.
Please install the proper power cut-off device during the installation connection.
Always follow the instruction guide the manufacturer recommended.
If this product is installed in the ceiling, please make sure the installation position can sustain the min
50N.
4．Qualified engineers needed
All the examination and repair work should be done by the qualified service engineers.
We are not liable for any problems caused by unauthorized modifications or attempted repair.
5．Environment
This series HDAVS camera should be installed in a cool, dry place away from direct sunlight or strong
light, inflammable, explosive substances and etc.
This series camera shall work on the specified working temperature. Please keep it away from the
electromagnetic radiation object and environment.
Please make sure the CMOS component is out of the radiation of the laser beam device. Otherwise it
may result in CMOS optical component damage.
Please keep the sound ventilation.
Do not allow the water and other liquid falling into the camera.
6. Accessories
Be sure to use all the accessories recommended by manufacturer.
Before installation, please open the package and check all the components are included.
Contact your local retailer ASAP if something is broken in your package.
7. Daily Maintenance

iv
Please shut down the device and then unplug the power cable before you begin daily maintenance
work.
Use the dry soft cloth to clean the device. If there is too much dust, please use the water to dilute the
mild detergent first and then use it to clean the device. Finally use the dry cloth to clean the device.
Please put the dustproof cap to protect the CMOS component when you do not use the camera.

v
Applicable model
This manual can be applied to the following model:
HD2-B27-M

1
1General Introduction
1.1 Overview
This series HDAVS camera conforms to the HDAVS standard. It supports video signal high-
speed long distance transmission without any delay. It can be controlled by the DVR
conforming to the HDAVS.
1.2 Features
High-performance CMOS image sensor, megapixel definition.
Restore clear and vivid video.
Default motorized vari-focal lens, support coaxial control lens zoom and focus.
Support external audio source input.
Support 1 channel external alarm signal input, 1 channel alarm output.
Support audio, control and video coaxial transmission.
For 720P series, support 75-3 coaxial cable transmission without any loss. The distance is
over 500m. For 1080P series, support 75-3 coaxial cable transmission without any loss.
The distance is over 300m. High speed, long distance real-time transmission.
Support HDAVSHD and analog SD switch output.
Support high performance 3D noise reduction.
Support intelligent IR function, max IR distance 50m.
Support ICR switch to realize surveillance both in the daytime and at night.
Support OSD (on-screen display) menu to adjust parameters.
Support privacy tampering, AWB, AE, auto aperture and other functions.
Support DC12V/AC24V power supplying.
Support IP66 protection level.
Can be applied to finance, supermarket, telecommunication, government, school, airport,
factory, hotel and other places which need HD video.

2
2Device Framework
2.1 Framework and Dimension
Please refer to the figure2-1 for dimension information. The unit is mm.
Figure 2-1
2.2 Structure Component
Figure 2-2

3
See Sheet 2-1 for more details about ports.
SN Cable
Color Port Name Function
1 Green ALARM_NO On-off alarm output end.
2 Orange ALARM_NC On-off alarm output end.
3 Red ALARM_IN Alarm signal input end.
4 Black ALARM_GND Alarm signal input GND.
5
Brown,
White SD/HD Switch
Control Cable
It can realize the switch from HD video output to SD
video output when it is short circuit SD/HD switch
control cable. On the contrary, the open circuit
control cable will switch back to HD video output.
6
/
Audio Input Port
External Audio Source Input.
Note:
You need to set the camera’s “Audio Mode”as
“External Audio”when using external audio source
input.
7
/
Video Output Port
In the HD output mode, it sends video stream
according to HDAVS standard, and supports the
transmission of audio stream and control data
stream at the same time, and the back-end needs
to connect to HCVR to control; it transmits video
signal via CVBS signal in SD output mode.
8 / Power Input Port Input DC12V/AC 24V.
Sheet 2-1
Figure 2-3
2.3 Lens Zoom Adjustment
Users can coaxial control lens zoom and focus via back-end HCVR device, it can also be
realized by pressing up, down, left and right buttons, pressing up button means focus +,
pressing down button means focus -, pressing left button means zoom out, pressing right
button means zoom in.
Note:
Users need to operate again after exiting OSD menu when left and right buttons failed to
realize zoom function during OSD menu operation.

4
3Installation
Important
Before the installation, please make sure the installation surface can sustain at
least 3X weight of the bracket and the camera.
Step 1 Select installation mode, install camera bracket according to the exact installation mode.
Note:
First please pull the cable through exit hole on the installation surface or the bracket before
installing the bracket.
Users need to install expansion bolt first if the surface is cement (need to stick an installation
position map on the wall first to keep accordance between the installation hole of the
expansion bolt and the bracket), then install the bracket, as shown in Figure 3-1.
Users can skip the first step if the surface is wooden, and use self-tapping screws to install
bracket directly.
Step 2 Install the camera on the wall by using self-tapping screws.
Step 3 Unscrew the adjusting screws by using an L-shaped wrench in the accessories bag,
adjust the camera to a proper location which needs monitoring, then secure the adjusting
screws and fix the camera, as shown in Figure 3-1 (A and B).
Step 4 Connect the video output port of device cable to the back-end HCVR device, and
connect the power port to power supply.
Step 5 Adjust the lens zoom and focus to make video clear on the back-end HCVR device (it
also can be done via five direction buttons). So far, camera installation is completed.

5
Figure 3-1

6
4Menu
4.1 HDAVS Local Settings
This series HDAVS camera can adjust OSD menu via coaxial control.
4.1.1 Control Coaxial Device
After connected the camera to the HCVR, from Main Menu-> System ->PTZ, you need to
select the channel number to access and set control mode as HDAVS and the protocol as DH-
SD1. Click “save”button to save current setup. See Figure 4-1.
Figure 4-1
4.1.2 Set Audio Coax
From “Main Menu > Setting > Camera > Encode > Encode”, you need to set “Audio Format” as
“G711a” and the “Audio Source” as “HDAVS”. See Figure 4-2 for more details.

7
Figure 4-2
4.1.3 Open Menu
On the preview interface, right click mouse and then select PTZ; you can see an interface
shown as below. See Figure 4-3.
Figure 4-3
Click Iris “+”to open menu or confirm current operation.
Click up/down button to select all the parameters on the left pane of the first-level menu. Click
left/right button to set the corresponding values on the right pane of the parameters. If there is
“ ”, click Iris “+”button to go to the next menu and conduct the above operations. Click
“Return “button to go back to the previous menu interface.
Click Iris “-“to auto focus with current rate, click direction button to make lens reset.
Note:

8
The operation interface above is just an example of HCVRHG-AF series, the operation
interface may differ according to different back-end devices; please refer to corresponding
HCVR manual for detailed operations.
Users can also adjust OSD menu via 5-direction buttons. The exact operation is as follows:
press the middle button for about 2 seconds, and the OSD menu will display on the monitor
screen. The functions of up, down, left and right buttons are the same as in the figure above,
the middle button is equal to Iris “+”.
4.2 Menu List
The 1
st
The 2nd The 3
rd
Format PAL Confirm,
Cancel
NTSC Confirm,
Cancel
Video
Mode 1080P@25 /
1080P@30 /
720P@25 /
720P@30 /
720P@50 /
720P@60
Confirm,
Cancel
Backlight
Mode BLC BLC On, Off
WDR WDR 0～5
HLC HLC 0～5
Note:
The HLC
can only
be
displayed
when auto
exposure
mode and
outdoor
anti-flicker
mode are
both valid.
Off
Image
Adjustmen
t
Image
Mode Standard/ Soft/Vivid
Sharpness 0～100
Brightness 0～100
Contrast 0～100
Saturation 0～100
Sharp
suppress 0～100
Chroma
suppress 0～100
Gamma 0～15
2DNR 0～100
3DNR 0～100
Return/Exit

9
The 1
st
The 2nd The 3
rd
Exposure Exposure
Mode Auto Gain Max 0～100
Gain Min 0～100
Return/Exi
t Note: For the 2nd and the
3rd menu, when you
click Exit button to
exit, system saves
current setup by
default.
Low Noise
Gain Max 0～100
Return/Exi
t Note: For the 2nd and the
3rd menu, when you
click Exit button to
exit, system saves
current setup by
default.
Low
Motion
Blur
Shutter
Max PAL ：0ms ～
40ms
NTSC ：0ms ～
33ms
Return/Exi
t
Manual Shutter 1/100000、
1/10000、1/4000、
1/2000、1/1000、
1/500、1/250、
1/120、1/100、
1/60、1/50、1/30、
1/25、1/15、1/12、
1/10、1/8、1/6、
1/5、1/4、1/3
Customized Range
Note:
Shutter value is
linked to format.
Gain Max 0～100
Gain Min 0～100
Return/Exi
t
Exposure
Level 0～14
Exposure
Speed 0～7
Anti-flicker Outdoor
/50HZ/60H
Z
Note:
Value is
linked to
the format.
50HZ ：1/50 、
1/100 、1/25 、
1/10、1/5、1/4
60HZ ：1/60 、
1/120 、1/30 、
1/4、1/12、1/6
Note:
The exposure time is
different between
50HZ and 60HZ.

10
The 1
st
The 2nd The 3
rd
Besides, there are
no exposure modes
as anti-flicker and
low noise.
Return/Exi
t
White
Balance Auto
Manual Blue gain 1～100
Red Gain 1～100
Return/Exi
t
Day
Night
Indoor
Outdoor
Day/Night Auto
Note:
the 2nd menu
is only valid to
non-
photosensor
device.
Day/Night 1～100
Waiting
time 1～15
Return/Exi
t
B/W
Color
Language Chinese/Traditi
onal
Chinese/Englis
h
Advanced Camera
Title
Mirror Horizontal
Mirror Off/On
Vertical
Mirror Off/On
Return/Exit
D-Zoom 1~10
Lens Type Manual/D
C
Lens
Reset
IR Control
Note:
Only valid
to IR
device.
Auto
IR
Normally
Closed
Privacy
Mask Off
On Area
Select 0～7
Note:
There are eight
privacy mask zones
ranging from 0 to 7.
You need to set
parameters for each
zone, support max 8
zone setup.
Display Off/On
Area Setup Position

11
The 1
st
The 2nd The 3
rd
Size
Note:
Use direction buttons
to adjust position and
zone size.
Restore
Default
Return/Exit
485 Setup Address 1～254
Apply
Return/Exit
System
Info Version XXXXXXXXX
Return/Exit
Return/Exit
Reset
Exit
Note:
The menu list above is an example for 1080P series, the only difference of the menu list for
720P series is about “Video Mode”, which shows that 720P series support 720P@25,
720P@30, 720P@50, 720P@60.

12
Appendix Toxic or Hazardous Materials or Elements
Component
Name
Toxic or Hazardous Materials or Elements
Pb Hg Cd Cr VI PBB PBDE
Circuit Board
Component ○○○○○○
Device
Construction
Material
○
○○○○○
Wire and Cable ○
○○○○○
Packing
Components ○○○○○○
Accessories ○○○○○○
O: Indicates that the concentration of the hazardous substance in all homogeneous materials
in the parts is below the relevant threshold of the SJ/T11363-2006 standard.
X: Indicates that the concentration of the hazardous substance of at least one of all
homogeneous materials in the parts is above the relevant threshold of the SJ/T11363-2006
standard. During the environmental-friendly use period (EFUP) period, the toxic or hazardous
substance or elements contained in products will not leak or mutate so that the use of these
(substances or elements) will not result in any severe environmental pollution, any bodily injury
or damage to any assets. The consumer is not authorized to process such kind of substances
or elements, please return to the corresponding local authorities to process according to your
local government statutes.
Note
This manual is for reference only. Slight difference may be found in the user
interface.
All the designs and software here are subject to change without prior written
notice.
All trademarks and registered trademarks mentioned are the properties of their
respective owners.
If there is any uncertainty or controversy, please refer to the final explanation of
us.
Please visit our website or contact your local service engineer for more
information.