Clifford Matrix RSIII User manual

MODEL
RSIII
Remote Start with
Security System
OWNER’S GUIDE
now
with

i
© 2002 directed electronics, inc.
lliimmiitteeddlliiffeettiimmeeccoonnssuummeerrwwaarrrraannttyy
Directed Electronics, Inc. ("Directed") promises to the original purchaser to repair or
replace with a comparable reconditioned model any Directed unit (hereafter the "unit"),
excluding without limitation the siren, the remote transmitters, the associated sensors and
accessories, which proves to be defective in workmanship or material under reasonable use
during the lifetime of the vehicle provided the following conditions are met: the unit was
professionally installed and serviced by an authorized Directed dealer; the unit will be pro-
fessionally reinstalled in the vehicle in which it was originally installed by an authorized
Directed dealer; and the unit is returned to Directed, shipping prepaid with a legible copy
of the bill of sale or other dated proof of purchase bearing the following information: con-
sumer's name, telephone number and address; the authorized dealers name, telephone
number and address; complete product description, including accessories; the year, make
and model of the vehicle; vehicle license number and vehicle identification number. All
components other than the unit, including without limitation the siren, the remote trans-
mitters and the associated sensors and accessories, carry a one-year warranty from the date
of purchase of the same. This warranty is non-transferable and is automatically void if: the
original purchaser has not completed the warranty card and mailed it within ten (10) days
of the date of purchase to the address listed on the card; the unit's date code or serial num-
ber is defaced, missing or altered; the unit has been modified or used in a manner con-
trary to its intended purpose; the unit has been damaged by accident, unreasonable use,
neglect, improper service, installation or other causes not arising out of defects in materi-
als or construction. The warranty does not cover damage to the unit caused by installa-
tion or removal of the unit. Directed, in its sole discretion, will determine what consti-
tutes excessive damage and may refuse the return of any unit with excessive damage. TO
THE MAXIMUM EXTENT ALLOWED BY LAW, ALL WARRANTIES, INCLUD-
ING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY,
WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE
AND WARRANTY OF NON-INFRINGEMENT OF INTELLECTUAL PROPERTY,
ARE EXPRESSLY EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR
AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY,
OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS.
DIRECTED DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY
AND ALL ACTS OF THIRD PARTIES INCLUDING ITS AUTHORIZED DEAL-
ERS OR INSTALLERS. DIRECTED SECURITY SYSTEMS, INCLUDING THIS
UNIT, ARE DETERRENTS AGAINST POSSIBLE THEFT. DIRECTED IS NOT
OFFERING A GUARANTEE OR INSURANCE AGAINST VANDALISM, DAM-
AGE OR THEFT OF THE AUTOMOBILE, ITS PARTS OR CONTENTS; AND
HEREBY EXPRESSLY DISCLAIMS ANY LIABILITY WHATSOEVER, INCLUD-
ING WITHOUT LIMITATION, LIABILITY FOR THEFT, DAMAGE AND/OR
VANDALISM. THIS WARRANTY DOES NOT COVER LABOR COSTS FOR
MAINTENANCE, REMOVAL OR REINSTALLATION OF THE UNIT OR ANY

ii © 2002 directed electronics, inc.
CONSEQUENTIAL DAMAGES OF ANY KIND. IN THE EVENT OF A CLAIM
OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER
VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA.
CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY
AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY
CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE
AUTHORIZED DIRECTED DEALER'S PURCHASE PRICE OF THE UNIT.
DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEV-
ER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES,
INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF
EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY
AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER
DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR THE CON-
TROL MODULE AS DESCRIBED ABOVE. Some states do not allow limitations on
how long an implied warranty will last or the exclusion or limitation of incidental or con-
sequential damages. This warranty gives you specific legal rights and you may also have
other rights that vary from State to State.
This product may be covered by a Guaranteed Protection Plan ("GPP"). See your autho-
rized Directed dealer for details of the plan or call Directed Customer Service at 1-800-
876-0800. Directed security systems, including this unit, are deterrents against possible
theft. Directed is not offering a guarantee or insurance against vandalism, damage or theft
of the automobile, its parts or contents; and hereby expressly disclaims any liability what-
soever, including without limitation, liability for theft, damage and/or vandalism.
Directed does not and has not authorized any person or entity to create for it any other
obligation, promise, duty or obligation in connection with this security system.
Make sure you have all of the following information from your dealer:
A clear copy of the sales receipt, showing the following:
➤Date of purchase
➤Your full name and address
➤Authorized dealer's company name and address
➤Type of alarm installed
➤Year, make, model, and color of the automobile
➤Automobile license number
➤Vehicle identification number
➤All security options installed on automobile
➤Installation receipts

1
© 2002 directed electronics, inc.
rreemmootteeccoonnttrroollddiiaaggrraamm........................22
ssttaannddaarrddrreemmootteeccoonnffiigguurraattiioonnss..............33
wwhhaattiissiinncclluuddeedd....................................44
iimmppoorrttaannttiinnffoorrmmaattiioonn..........................44
warning! safety first . . . . . . . . . . . .5
system maintenance . . . . . . . . . . .7
your warranty . . . . . . . . . . . . . . . .8
fcc/id notice . . . . . . . . . . . . . . . . .8
caution . . . . . . . . . . . . . . . . . . . . .8
rreemmootteeccoonnttrroollffuunnccttiioonnss......................99
standard button configurations . . .9
standard icon configurations . . . .10
rreemmootteeooppeerraattiioonnaannddpprrooggrraammmmiinngg
iinnssttrruuccttiioonnss........................................1133
system signal paging features . . . .13
programmable remote control
features . . . . . . . . . . . . . . . . . . . .15
uussiinnggyyoouurrssyysstteemm................................1166
active arming . . . . . . . . . . . . . . .16
passive arming . . . . . . . . . . . . . .17
vehicle protection . . . . . . . . . . . .18
warn away®response description .19
triggered response description . . .20
arming/disarming while driving . .21
multi-level security arming . . . . .22
disarming . . . . . . . . . . . . . . . . . .23
high security disarm . . . . . . . . . .24
disarming without a transmitter
(emergency override) . . . . . . . . . .24
silent mode . . . . . . . . . . . . . . . . .25
panic mode . . . . . . . . . . . . . . . . .26
valet mode . . . . . . . . . . . . . . . . .26
remote start . . . . . . . . . . . . . . . .28
valet take-over . . . . . . . . . . . . . . .30
timer mode . . . . . . . . . . . . . . . . .31
ssaaffeettyyffeeaattuurreess......................................3333
starter anti-grind circuitry . . . . . .33
disabling the remote start system .33
over and under rev protection . . .34
shut down inputs . . . . . . . . . . . .34
nuisance prevention circuitry . . . .34
ddiiaaggnnoossttiiccss..........................................3366
arming diagnostics . . . . . . . . . . .36
disarming diagnostics . . . . . . . . .37
system status chirps . . . . . . . . . . .37
table of zones . . . . . . . . . . . . . . .38
interpreting zone diagnostics . . . .38
ccooddeehhooppppiinngg......................................4400
oowwnneerrrreeccooggnniittiioonn..............................4400
rraappiiddrreessuummeellooggiicc..............................4411
ppoowweerrssaavveerrmmooddee................................4411
pprrooggrraammmmiinnggooppttiioonnss..........................4422
sseeccuurriittyy&&ccoonnvveenniieenncceeeexxppaannssiioonnss......4455
gglloossssaarryyoofftteerrmmss..................................4477
ttaabblleeooffccoonntteennttss

2© 2002 directed electronics, inc.
rreemmootteeccoonnttrroollddiiaaggrraamm
4
9
13
11
12
16
14
17
19
20
21
22
18
15
3
21
56
78
25
10
24
23

3
© 2002 directed electronics, inc.
ssttaannddaarrddrreemmootteeccoonnffiigguurraattiioonnss
1 Auxiliary Channel Out
2 Receive Indicator
3 Signal Indicator
4 Transmit Indicator
5 Lock Status Indicator
6 Unlock Status Indicator
7 Arming Status Indicator
8 Disarming Status Indicator
9 Door Switch Input Indicator
10 Warn Away®Response Indicator
11 Siren Status Indicator
12 Trigger Response Indicator
13 Vibrate Mode Indicator
14 Hood Switch Input Indicator
15 Ignition Switch Input Indicator
16 Sensor Response Indicator
17 Sensor 1 Indicator - Full Trigger and Warn Away®
18 Sensor 2 Indicator - Full Trigger and Warn Away®
19 Trunk Switch Input Indicator
20 Remote Start Indicator
21 Battery Level Indicator
22 Disarm Button
23 Auxiliary Button
24 Panic Button
25 Arm Button

4© 2002 directed electronics, inc.
wwhhaattiissiinncclluuddeedd
➤Control module
➤Receiver/antenna
➤One four-button Responder Technology remote control
➤Stinger™ DoubleGuard® two-stage shock sensor
➤Revenger™ Soft Chirp™ six-tone programmable siren
➤Red status LED indicator light
➤Push-button Valet® switch
➤Your warranty registration
➤FailSafe® Starter Kill
➤Shut-down toggle switch
iimmppoorrttaannttiinnffoorrmmaattiioonn
Congratulations on the purchase of your combination remote
start Responder Technology alarm system. Due to the complexity
of this system, it must only be installed by an authorized dealer.
Installation of this product by anyone other than an authorized
dealer voids the warranty. All dealers are provided with a
preprinted dealer certificate to verify authorization.
By carefully reading this Owner's Guide prior to using your
system, you will maximize the use of this system and its features.
You can print additional or replacement copies of this manual by
accessing our web site at www.directed.com.

5
© 2002 directed electronics, inc.
warning! safety first
The following safety warnings must be observed at all times:
➤Due to the complexity of this system, installation of this
product must only be performed by an authorized Directed
dealer.
➤When properly installed, this system can start the vehicle via
a command signal from the remote control transmitter.
Therefore, never operate the system in an enclosed area or
partially enclosed area without ventilation (such as a garage).
When parking in an enclosed or partially enclosed area or
when having the vehicle serviced, the remote start system
must be disabled using the installed toggle switch. It is the
user's sole responsibility to properly handle and keep out of
reach from children all remote control transmitters to assure
that the system does not unintentionally remote start the
vehicle. TTHHEEUUSSEERRMMUUSSTTIINNSSTTAALLLLAACCAARRBBOONN
MMOONNOOXXIIDDEEDDEETTEECCTTOORRIINNOORRAABBOOUUTTTTHHEE
LLIIVVIINNGGAARREEAAAADDJJAACCEENNTTTTOOTTHHEEVVEEHHIICCLLEE..AALLLL
DDOOOORRSSLLEEAADDIINNGGFFRROOMMAADDJJAACCEENNTTLLIIVVIINNGG
AARREEAASSTTOOTTHHEEEENNCCLLOOSSEEDDOORRPPAARRTTIIAALLLLYY
EENNCCLLOOSSEEDDVVEEHHIICCLLEESSTTOORRAAGGEEAARREEAAMMUUSSTTAATT
AALLLLTTIIMMEESSRREEMMAAIINNCCLLOOSSEEDD..These precautions are
warning! THIS SYSTEM PROVIDES REMOTE NOTI-
FICATION OF SECURITY SYSTEM TRIGGER
EVENTS. CONTACT POLICE OR SECURITY PER-
SONNEL IMMEDIATELY. NEVER CONFRONT A
CAR THIEF OR VANDAL.
➜

6© 2002 directed electronics, inc.
the sole responsibility of the user.
➤Use of this product in a manner contrary to its intended
mode of operation may result in property damage, personal
injury, or death. (1) Never remotely start the vehicle with the
vehicle in gear, and (2) Never remotely start the vehicle with
the keys in the ignition. The user must also have the neutral
safety feature of the vehicle periodically checked, wherein
the vehicle must not remotely start while the car is in gear.
This testing should be performed by an authorized Directed
dealer in accordance with the Safety Check outlined in the
product installation guide. If the vehicle starts in gear, cease
remote start operation immediately and consult with the
authorized Directed dealer to fix the problem.
➤After the remote start module has been installed, contact
your authorized dealer to have him or her test the remote
start module by performing the Safety Check outlined in the
product installation guide. If the vehicle starts when
performing the Neutral Safety Shutdown Circuit test, the
remote start unit has not been properly installed. The
remote start module must be removed or the installer must
properly reinstall the remote start system so that the vehicle
does not start in gear. All installations must be performed by
an authorized Directed dealer. OOPPEERRAATTIIOONNOOFFTTHHEE
RREEMMOOTTEESSTTAARRTTMMOODDUULLEEIIFFTTHHEEVVEEHHIICCLLEE
SSTTAARRTTSSIINNGGEEAARRIISSCCOONNTTRRAARRYYTTOOIITTSS
IINNTTEENNDDEEDDMMOODDEEOOFFOOPPEERRAATTIIOONN..OOPPEERRAATTIINNGG
TTHHEERREEMMOOTTEESSTTAARRTTSSYYSSTTEEMMUUNNDDEERRTTHHEESSEE

7
© 2002 directed electronics, inc.
CCOONNDDIITTIIOONNSSMMAAYYRREESSUULLTTIINNPPRROOPPEERRTTYY
DDAAMMAAGGEEOORRPPEERRSSOONNAALLIINNJJUURRYY..YYOOUUMMUUSSTT
IIMMMMEEDDIIAATTEELLYYCCEEAASSEETTHHEEUUSSEEOOFFTTHHEEUUNNIITTAANNDD
SSEEEEKKTTHHEEAASSSSIISSTTAANNCCEEOOFFAANNAAUUTTHHOORRIIZZEEDD
DDIIRREECCTTEEDDDDEEAALLEERRTTOORREEPPAAIIRROORRDDIISSCCOONNNNEECCTT
TTHHEEIINNSSTTAALLLLEEDDRREEMMOOTTEESSTTAARRTTMMOODDUULLEE..
DDIIRREECCTTEEDDWWIILLLLNNOOTTBBEEHHEELLDDRREESSPPOONNSSIIBBLLEEOORR
PPAAYYFFOORRIINNSSTTAALLLLAATTIIOONNOORRRREEIINNSSTTAALLLLAATTIIOONN
CCOOSSTTSS..
system maintenance
This system needs no specific maintenance beyond remote
control battery replacement. The remote is powered by a 1.5V
AAA battery.
The Battery Level indicator has four level indicators that serve as
a visual indication of battery charge. When the battery reaches a
low charge level that requires replacement, the remote control
will generate a single notification chirp, and the Battery Level
indicator will flash continuously.
Battery Replacement
Gently pull the end of the battery door away from the top of the
remote control then slide the door up to expose the battery and
remove the expired battery. Place the new battery into the remote
control observing the correct polarity. When power is returned
EMPTY
REPLACE
FULL
➜

8© 2002 directed electronics, inc.
the remote control will light all icons in the LCD and generate
all beeper tones once.
your warranty
Your warranty registration must be completely filled out and
returned within 10 days of purchase. Your product warranty
will not be validated if your warranty registration is not returned.
Make sure you receive the warranty registration from your dealer.
It is also necessary to keep your proof of purchase, which reflects
that the product was installed by an authorized dealer.
fcc/id notice
This device complies with Part 15 of FCC rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to
operate this device.
caution
This product is designed for fuel-injected, automatic transmis-
sion vehicles only. Use of this product in a standard transmission
vehicle is dangerous and contrary the product's intended use.
➜
➜
➜

9
© 2002 directed electronics, inc.
rreemmootteeccoonnttrroollffuunnccttiioonnss
The remote control buttons are used to send commands to the
system. The descriptions below reflect the standard configuration
for this system. The buttons can be custom configured for the
user’s specific needs by the installer.
standard button configurations
Button
The System Arm and Multi-Level Security Arming functions are
controlled by pressing this button for one second.
Button
The System Disarm and High Security Disarm functions are
controlled by pressing this button for one second.
Button
Silent Mode™ and an optional auxiliary function are controlled
by this button. Silent Mode works by pressing this button for less
than one second before arming or disarming. An optional auxil-
iary function, such as trunk release, can be controlled by pressing
this button for 1.5 seconds.
The auxiliary output controls __________________________.
Button
The panic feature is controlled by pressing this button for two
seconds.
➜

10 © 2002 directed electronics, inc.
and Buttons
The remote start function of your system is controlled by
pressing these buttons simultaneously for one second.
and Buttons
An optional auxiliary channel output for controlling additional
convenience or expansion functions that you have added to your
system can be operated by pressing these buttons simultaneously.
The auxiliary output controls __________________________.
standard icon configurations
Icon
The transmit icon will be displayed while the remote control is
transmitting a command to the vehicle.
Icon
The receive icon will be displayed while the remote control is
receiving a page from the vehicle.
Icon
The signal icon will be displayed if a command is transmitted to
the vehicle but a command page is not received.
Icon
The armed status icon will be displayed when the system is locked
and armed.
Icon
The disarmed status icon will be displayed when the system is
unlocked and disarmed.
➜

11
© 2002 directed electronics, inc.
Icon
The disarm icon will flash while the system is disarming
Icon
The arm icon will flash while the system is arming.
Icon
The door icon will be displayed to indicate that a door is open
when arming the system (Bypass Notification) or opened when
the system is armed (Tamper Alert).
Icon
The warn icon will be displayed if the Warn Away®response has
been triggered while the system is armed.
Icon
The siren icon will be displayed as an indicator that the siren is
sounding.
Icon
The alarm icon will be displayed if the system has been violated,
and will continue to be displayed until the 60-second siren cycle
is complete.
Icon
The vibrate icon will be displayed when the Vibrate Mode is on.
Icon
The battery level icon is always displayed as an indicator of
Battery charge.

12 © 2002 directed electronics, inc.
Icon
The start icon will be displayed while the vehicle is remote started.
Icon
The trunk icon will be displayed to indicate that the trunk is
open when arming the system (Bypass Notification) or opened
when the system is armed (Tamper Alert).
Icon
The Sensor 1 icon will be displayed if the Dual-Stage shock
sensor has been triggered as a full-triggered or Warn Away®
sequence.
Icon
The Sensor 2 icon will be displayed if an additional Dual-Stage
sensor has been triggered as a full-triggered or Warn Away®
sequence.
Icon
The hammer icon will flash when either Sensor 1 or 2 has been
triggered as either a Warn Away®response or triggered sequence.
Icon
The ignition icon will be displayed to indicate that the ignition
is on when arming the system (Bypass Notification) or turned on
when the system is armed (Tamper Alert).
note: If Page Mode has been turned off, the start icon will
remain when performing key take over until a button on
the transmitter has been pressed.

13
© 2002 directed electronics, inc.
Icon
The hood icon will be displayed to indicate that the hood is open
when arming the system or (Bypass Notification) opened when
the system is armed (Tamper Alert).
Number Icons
When either of the channel 2 or 4 outputs is activated the appro-
priate icon will be displayed for five seconds.
rreemmootteeooppeerraattiioonnaannddpprrooggrraammmmiinngg
iinnssttrruuccttiioonnss
The 554 remote start system operates at 434 MHz and incorpo-
rates Directed’s proprietary XHF2 out-board Responder
Technology remote control. The high frequency combined with
Binary Data communication achieves superior range with two-
way communication.
system signal paging features
A page is the signal the 554 control module sends to the remote
control as confirmation of receipt of a command or alarm system
status.
When the remote control receives a page it will generate a page
notification to the user (notifications are audible beeps or remote
vibration) and the LCD Icons will display the current system
status.
➜

14 © 2002 directed electronics, inc.
Command Page
When a command (arm/disarm, remote start, or auxiliary
channel) from the remote control is sent and received, the system
will send a command page back to confirm receipt.
Alarm Page
If the alarm system is triggered while armed, an Alarm Page will
be sent to the remote control. After receipt of an Alarm Page, the
LCD icons will display the alarm system status information and
the remote control will generate Alarm Page alerts.
An Alarm Page alert is a single beep or vibration from the remote
control every 60 seconds to alert the user that the alarm system
was triggered and will continue until the alarm page is cleared.
Page Recognition Mode
The remote control will leave a zone icon illuminated when it has
received a triggered response and will wait for you to recognize
the violation. Press any button on the remote control, the LCD
information and Alarm Page alerts will be cleared.
note: The remote control buttons will not send a com-
mand to the system until the alarm page is cleared.
note: If the transmiter is paged with an Alarm Page and
the WarnAway®is triggered before the Alarm Page is
recieved the transmitter will report the WarnAway®only
until the system is disarmed.
note: When the system is in Valet mode, the remote con-
trol will show the lock (5) and unlock (6) icons, but will
not generate a command page.

15
© 2002 directed electronics, inc.
programmable remote control features
To enter programming mode
Press and hold all four remote control buttons simultaneously
until one long beep is heard. Programming Mode has now been
entered.
Page Notification
The remote control can be programmed to notify the user of a
page by audibly beeping or remote vibration.
Beep Mode
Beep Mode includes alarm arm/disarm diagnostic beeps and
distinctive two-tone remote start beeps.
Vibrate Mode
Vibrate Mode makes page notification silent but does not include
diagnostic information or distinctive remote start notification.
Illumination
Illumination for the LCD display can be programmed on or off.
When programmed on the LCD will illuminate every time the
remote control receives a page or transmits a command.
Programming illumination on will decrease the life expectancy of
the battery.
Beep/Vibrate Mode
Within five seconds of entering Programming Mode, press .
The remote control will beep once for on, twice for off. The
vibrate icon (12) will also turn on/off with each press.
➜

16 © 2002 directed electronics, inc.
Illumination On/Off
Within five seconds of entering Programming Mode, press .
The remote will beep once for on, twice for off and the light will
turn on/off with each press.
Page Mode On/Off
After entering Programming Mode, press within five
seconds to toggle on and off. When the Page Mode is on, the
remote control will wake up periodically to check for messages
from the security module. It will also wake up when any button
is pushed. When Page Mode is off, the remote control “sleeps”
until a button is pushed, extending the life of the battery.
To Exit Programming Mode
To exit Programming Mode, take no action for five seconds. The
remote control will generate two beeps to indicate programming
mode has been exited.
uussiinnggyyoouurrssyysstteemm
active arming
Press for one second to arm the system. The vehicle’s lights
will flash once, the doors will lock, the siren will chirp once, and
while the system is armed, the status LED will blink approxi-
mately once per second to indicate the system is actively
protecting the vehicle.
➜

17
© 2002 directed electronics, inc.
The remote control will beep once (or vibrate). The arm icon (7)
will flash for five seconds and the armed status icon (4) will be
displayed on the LCD.
Bypass Notification
If the siren chirps again, the remote control beeps again, and the
status LED blinks in a pattern, a protected entry or sensor input
is active and its icon will be displayed on the remote control LCD.
This is called Bypass Notification. Refer to the diagnostic section
of this manual for information about Bypass Notification.
passive arming
The system can be programmed to arm automatically. This is
called passive arming. In Passive Arming Mode the system will
arm itself 30 seconds after the user exits the vehicle and closes all
protected entry points.
Passive arming sequence
1. Turn the ignition off and exit the vehicle.
2. Close all protected entry points. (doors, hood, trunk)
3. The status LED will blink at twice its normal rate indicating
the system has begun the 30 second countdown.
4. After 20 seconds the siren will chirp once (unless
programmed off) as an audible indication that the system is
about to arm.
5. At 30 seconds the system will fully arm itself. At this time the
lights will flash and the doors will lock (if programmed for
passive locking).
➜