Clinton Electronics CE-PSG-5088V User manual
FCC Statement
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in
a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equip-
ment in a residential area is likely to cause harmful interference
in which case the user will be required to correct the interference
at his own expense.
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
Any changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority
to operate the equipment.
CE Warning
This is a class A product. In a domestic environment, this product
may cause radio interference, in which case the user may be re-
quired to take adequate measures.
DISCLAIMER
Clinton Electronics reserves the right to change the contents of
this manual without prior notice.
WARNING
Changes or modifications not expressly approved by the man-
ufacturer could void the user’s authority to operate the equip-
ment.
CAUTION
To prevent electric shock and risk of fire hazards:
• Do NOT use power sources other than that specified.
• Do NOT expose the inside of this appliance to rain or moisture.
This Switch provides (8) 10/100/1000Mbps NWAY RJ-45 ports.
It was designed for easy installation and high performance in an
environment where trac on the network and the number of us-
ers increase continuously. With the newest Gigabit chip set, this
Gigabit Ethernet switch can fully support the highest speed with-
out problem, even when Full-Duplex is under load.
It consists of (8) PSE/PoE+ ports that can solve the limitation of
the power outlet location and oer the system designer a flexible
solution to locate the network device everywhere.
This is specifically designed for medium to large work-groups.
This Switch can be installed where space is limited; moreover it
provides smooth network migration and is an easy upgrade to
network capacity.
INTRODUCTION
Before you start to install this 8-Port Gigabit Ethernet Switch,
please verify that the box contains the following items:
( 1 ) 8-Port Gigabit Ethernet Switch
( 1 ) AC Power Cord
( 1 ) Quick Installation Guide
( 1 ) Rack-Mount Bracket
PACKAGE CONTENTS
• Complies with the IEEE802.3 Ethernet, IEEE802.3u Fast Ether-
net and IEEE 802.3ab/z Gigabit Ethernet Standards
• Provides (8) 10/100/1000Mbps Gigabit switching ports
• Supporting the power Max. 30 Watts for each PSE/PoE+ port
with total power consumption of 130 Watts (Max)
• Non-blocking & Non-head-of-line blocking full wire speed for-
warding
• Store-and-forward operation support
• Provides 8K MAC address entry
• Supports broadcast storm filtering
• All ports provide Auto-Negotiation and Auto-MDI/MDI-X func-
tions
• Supports flow control: back pressure for Half-duplex and IEEE
802.3x for Full-duplex mode
• Smart plug & play
KEY FEATURES
Sales: 1-800-447-3306 Support: 1-800-549-6393
www.clintonelectronics.com
6701 Clinton Road. Loves Park, IL 61111
NOTE: If a status LED doesn’t indicate a link or activity, check
the corresponding device for proper connection, setup and op-
eration.
LED STATUS DESCRIPTION
Power On Power is ON
O Power is OFF
PoE
On Port is linked to a
PSE/PoE device
O No PSE/PoE device is
linked
LINK / ACT
On Valid port connection
Flashing
Valid port connection,
Data transmited/
received
O No link established
FRONT PANEL (LEDs)
The LED indicators: Power, PoE, Link/Activity make it easier to
monitor the switch and its connections.
All manuals and user guides at all-guides.com
As with any electrical device, you should place the switch where
it will not be subjected to extreme temperatures, humidity or
electromagnetic interference:
• Place the switch on a level surface with at least 25 mm (approx.
1”) of clearance for ventilation.
• The ambient temperature should be between 32 and 104 de-
grees Fahrenheit.
• The relative humidity should be less than 90 percent, non-con-
densing.
• Surrounding electrical devices should not exceed the electro-
magnetic field (RFC) standards for IEC 801-3, Level 2 (3V/M)
field stength.
• Make sure that the switch receives adequate ventilation. Do not
block the fan exhaust port on the switch.
• The power outlet should be within 5 feet of the switch.
• Do not place objects on top of the unit.
• Always avoid dust and dirt.
INSTALLATION TIPS
REAR PANEL (POWER)
Use the included power cord to connect the device (next to
the On/O switch on the rear panel) to an AC outlet. Confirm
that the power LED on the front panel is lit.
TECHNICAL SPECIFICATIONS
Standards
IEEE 802.3 10BaseT
IEEE 802.3u 100BaseTX
IEEE 802.3ab 1000BaseT
IEEE 802.3z
IEEE 802.3x Flow control
IEEE 802.3at PoE+
Features
10/100/1000BaseTX
(8) RJ-45 Connectors
MAC Address: 8K
Buer memory: 2M bit
Method: Store and Forward
Filtering/
Forwarding
Rates
1000Mbps port – 1,488,000pps
100Mbps port – 148,800pps
10Mbps – 14,880pps
LED Indicators Power and PD Link
Power
Requirement 100~240V/AC, 50~60Hz
Power
Consumption 130 Watts (Max)
Dimensions
(L x W x H) 10.47” x 6.3” x 1.73”
Weight 3.35 lbs
Operating
Temperature
32°F ~ 104°F
10 ~ 90% RH (non-condensing)
Certifications UL, FCC Class A, CE
Switch/Hub to this 8 Port Gigabit Ethernet Switch
This switch provides automatic crossover detection functionality
for any port. It is simple and friendly to up-link to another switch
without crossover cable.
PC/Other devices to this 8 Port Gigabit Ethernet Switch
Via a twisted pair cable straight through, this switch can be con-
nected to PCs, servers and other network devices.
CONNECTIONS CONNECTIONS
IP Camera
Computer
VoIP
Phone
Access
Point
IP Cameras
Computers
Dual Speed Hub
Ethernet
Switch
Ethernet
Switch
Server
Work Group
Clinton reserves the right, without notification, to make changes in product design & specification.
v.01.16.15
All manuals and user guides at all-guides.com
Other Clinton Electronics Switch manuals
