CNP Brands Bebe Care Rverse XLR User manual

RVERSE XLR
TODDLER SEAT
MODEL # 125422
IMPORTANT: RETAIN FOR FUTURE REFERENCE, READ CAREFULLY
Assembly Contents
2 Year Diamond Warranty Terms and Conditions
Thank you for your purchase of this quality product from CNP Brands. To register your 2 year warranty and to
view our warranty conditions, visit www.cnpbrands.com.au.
Safety Precautions
Before assembling this stroller seat, read and understand the instructions. Incorrect assembly may make the stroller
seat unsafe. Do not use this stroller seat if any part is broken, torn or missing. Keep these instructions in a safe
place for future reference.
The pram/stroller may become unstable if excessive weight is on it.
Toddler seat only to be positioned facing forward in the bottom rear of the stroller.
Maximum recommended child height and weight in the toddler seat is 90cm/16kgs.
Toddler seat must be removed before folding the pram/stroller.
Promptly replace worn out or broken parts.
Do not use accessories other than those supplied and approved by CNP Brands.
Do not make any changes or alterations to this product, unless through an approved service agent.
For warranty purposes, keep your sales receipt to provide proof of purchase.
Never leave safety harness connected when not fitted to a child in the stroller as this may create loops that could cause a strangulation hazard.
TO AVOID INJURY OR DEATH:
FOLLOW THE MANUFACTURER’S INSTRUCTIONS.
ALWAYS APPLY THE BRAKES WHENEVER THE PRAM/STROLLER IS STATIONARY.
USE THE TETHER STRAP AT ALL TIMES TO PREVENT THE PRAM/STROLLER ROLLING AWAY.
DO NOT LEAVE CHILDREN UNATTENDED.
SECURE THE CHILD IN THE HARNESS AT ALL TIMES.
MAKE SURE CHILDREN ARE CLEAR OF ANY MOVING PARTS IF YOU ADJUST THE PRAM/STROLLER,
OTHERWISE THEY MAY BE INJURED.
DO NOT USE THIS SEAT WITH ANY OTHER MODELS OF PRAM/STROLLER. THIS TODDLER SEAT IS
SPECIFICALLY DESIGNED TO BE USED ONLY WITH THE bebe care RVERSE XLR STROLLER MODEL # 015422.
DO NOT CARRY EXTRA CHILDREN OR BAGS ON THIS PRAM/STROLLER.
WARNING:
1. Seat (pre-assembled with removable seat pad and shoulder pads)
2. Canopy
3. Wheel Mud Guard x 2
4. Mounting Adaptor x 2
1.
2.
3. 4.
Distributed in Australia by CNP Brands, 20 Calarco Drive, VIC, 3030
Customer Service 1300 667 137 www.cnpbrands.com.au
Distributed in New Zealand by Wainhouse Distribution, 2-6 Argyle St,
Morningside, PO Box 41-014, St Lukes, Auckland, New Zealand
Customer Service: 0800 567 5000 [email protected]
This product has been designed and manufactured to comply with Australian Safety Standard AS 2088:2009.
WARRANTY
STICKER TO BE
PLACED HERE

Assembly Instructions
RVERSE XLR
TODDLER SEAT
MODEL # 125422
Adjusting Canopy
Pull the canopy cover forward or
push backward.
Inserting Mounting Adaptors
Insert mounting adaptors into
the seat attachment slots on the
stroller frame. Ensure the mounting
adaptors are positioned forward
as shown to the right.
Attaching Wheel Mud Guards
Insert the wheel mud guards into
the rear wheel housing slots until it
clicks into place
Attaching Toddler Seat
Insert the toddler seat into the
attachment slots located in the
bottom rear leg of the stroller.
Backrest Adjustment
1. To lift backrest; attach the
webbing buckle together.
2. To lower backrest; release the
webbing buckle by pressing
the sides of the buckle.
To Uncover Window
Roll window cover down and
attach toggle to toggle loop when
window is in use.
To Remove Toddler Seat
Press orange lever on top rear of
the toddler seat and lift to remove
toddler seat from stroller.
Attaching Canopy
1. Attach canopy to the seat
frame, ensuring side clips
are attached securely on
the seat frame.
2. Attach press studs of the
rear of canopy together.
Restraints - Harness
1. To secure the child in the harness, place left hand buckle prong (b) on top of (a).
2. Hold both left hand buckle prongs (a) and (b) together and insert it into buckle
housing (e) until it snaps into position.
3. Repeat previous steps for right hand buckle prongs (c) and (d).
4. Once all attached, carefully adjust the harness straps by pulling each slider (f) until
the desired fit is achieved in the lap, shoulder and crotch straps.
5. To release the buckles, squeeze the top and bottom prongs (a) and (b), (c) and (d)
together until harness disengages.
CAUTION: Always adjust the harness when changing the seating position of the child.
f
ff
ff
a
b
c
d
e
(a), (b): Left hand buckle prongs
(c), (d): Right hand buckle prongs
(e): Buckle housing
(f): Strap adjustment sliders