COBAN GROUP 12000MAH User manual

1
GSM/GPRS/GPS
Long Time Standby Tracker
User Manual
Preface
Thank you for purchasing the tracker. This manual shows how to operate the
device smoothly and correctly. Make sure to read this manual carefully before
using this product. Please note that specification and information are subject to
changes without prior notice in this manual.
Any change will be integrated in the latest release. The manufacturer assumes
no responsibility for any errors or omissions in this document.

2
1. Introduction
The tracker working based on the GSM/GPRS/LBS/AGPS network and GPS
satellite positioning system, which set multiple functions of security, positioning,
monitoring surveillance, and tracking in its entirety. It can track and monitor
remote target by SMS or internet. Advantage:Long time standby,and no need
installation, just adsorb under the car bottom,itself has magnetic force.
2. Specifications
Content
12000MAH
DIM
120mm x 60mm x 30mm
Weight
250g
Band
850/900/1800/1900Mhz
Network
GSM/GPRS
GPS Chip
UBLOX7
GSM/GPRS Module
MTK6261D
GPS Sensitivity
-159dBm
GPS Start time
Cold start 45-120S
Warm start 35S
Hot start 1S
Voltages of car power
system
Input1 2-24V
Output 5V
Charger Voltage
Input 110V-220V
Output 5V
Battery
Device will send low power alarm when
voltage below 3.45V
Storage Temp
-40°C to +85°C
Operation Temp
-20°C to +65°C
Humidity
5%--95% non-condensing

3
3. Operating Instructions
For the first time activating the device, once Sim card is inserted, device
will be on automatically.
3.1 SIM Card Pre-installation, specification note
a. GSM Sim Only
b. SIM card should have its GPRS function enabled.
c. SMS request will function only if Caller ID function is enabled.
3.2 SIM Card Installations and Removal
a. Open waterproof rubber
b. Insert SIM card into the SIM slot.
c. Do not install it in a environment which is more than GSM performance
d. Call the device SIM number and it is supposed to get through
e. Ensure the waterproof rubber is closed after SIM installation
3.3 Device light description
Color stable lighting
Represents
yellow
GSM signal normal
blue
GPS signal normal
Red
Power

4
4. Setting By SMS
4.1 Single Locating
The center number set command:
g1234
Repy: Google map link +IMEI number + GPS status + Speed + Time
4.2 Set The Center Number
The center number set command:
admin123456 00000000000 ( Phone number)
Example: admin123456 18575518750
Reply: admin ok
(If you would like to delete the center number,please send “FORMA”to
initialize all the setting.)
4.3 Modify Password
The default password is 123456
Command: password123456 new password (6 digits)#
Example: password123456 888888#
Reply: password ok

5
4.4 Modify The Interval Time Of GPRS Data Upload
Command: upmove123456 time (In seconds) #
Example: upmove123456 120#(The default setting is 120s)
Reply : ok
The interval time of GPRS data upload can be set to between 1s and 300s.
4.5 Monitoring Voice Number Setting
Command: 88
If the command set successful, send the massage by your phone, then the device
will call back to monitor.
4.6 Mode Setting
1. Single working mode
Command: DW00 ( 00 means the time you want to set)
Example:DW05( The single working time set as five)
Reply: GPS Time Set OK
Five minutes later after your setting, it will run back to the default setting.
2.Default working mode
Command: auto123456 Reply: ok
The device will turn to sleeping mode if there is not any operation in10 minutes,
and the GPS and GPRS will turn off, shake it or sending command will let it

6
work again.
3.Keep working mode
Command:nslp123456 Reply: ok
The device will turn off the sleeping mode after this command.
4.7 Over Speed Alert ( By SMS)
1.set the highest speed
Command:speed123456 000 ( 000 means the time to set)
Example: speed123456 080 (The speed set as 80)
Reply: speed ok
2.turn off the speed alert
Command:speed123456 000
Reply: speed ok
4.8 Shock Alert
1.Turn on the shock alert( by SMS)
Command:125# Reply: ok
Turn off the shock alert(by SMS)
Command:126# Reply: ok

7
2.Turn on the shock alert( by Phone)
Command:122# Reply: ok
Turn off the shock alert( by Phone)
Command:121# Reply: ok
4.9 Movement Alert
Command: move123456 000
Example:move123456 300 (Default setting is 300 meter)
Reply: move ok
Command: nomove123456 ( Turn off the movement alert)
Reply: nomove ok
4.10 Setting Protection
Setting Protection Command: SF (Send this command after all the alarms are
set up, the alarms are effective after you open the protection).
Reply: SF ok
Undo Setting Protection Command: CF
Reply: CF ok
(The device will automatically disarm after an alarm, then need to re-send the
SF command , the alarms will be effective)

8
4.11 Restart Device and Settings Restore Factory
Restart Device Command: CQ
When the device received the command, it will reply “system reset ok”,and
then restart device after 1 min.
Settings Restore Factory Command: FORMA
When the device received the command, it will restore factory settings and auto
restart.
4.12 IP And Port Setting
Command: DOMAIN=IP or domain:port
Example: IP 220.231.203.248 7700
4.13 APN Setting
Set APN Name Command: apn123456 name
Set apn user Command: apnuser123456 user
Set APN passwords Command: apnpasswd123456 password
Example: indonisia telkomsel
APN name is internet ,user is wap , password is wap123.
then should set as follow:
apn123456 internet( The default operator is cmnet)
apnuser123456 wap
apnpasswd123456 wap123

9
4.14 Check setting status
Command: CXZT
Reply: Software version + ID no. +IP + port +APN + Mode + GPS status +
GSM status
5. GPS Tracking system
1) Make sure you have set the correct IP,Port,APN.
2) Enter: www.gpstky.net, then login with your account name and password pls.
3) Download APP “Tracker King” which can be downloaded from Google
play store or Apple play store.
4) Scan code to download “Tracker King”.