Cobra Marine MR HH350 FLT EU User manual

16 / 9TW
SCAN
WX
H M L
ESC
MEM
ENT SETUP
CALL
FLOATING
SUBMERSIBLE
MEMSAMEATISVOX LOM E D H I
ROG
VHF
T
R
A
B
GMRS
X
CIU
MARINE HH350
VHF MARINE RADIO
MR HH350 FLT
wner’s Manual
Our Th nks to You nd
Customer Assist nce
Introduction
Our Thanks to You •
Th nk you for purch sing Cobr M rine®VHF r dio.
Properly used, this Cobr ®product will give you
m ny ye rs of reli ble service.
How Your Cobr M rine VHF R dio Works
This radio is a battery-powered portable transceiver for use afloat. It gives you
two-way vessel-to-vessel and vessel-to-shore station communications, primarily
for safety and secondarily for navigation and operational purposes. With it, you
can call for help, get information from other boaters, talk to lock or bridge tenders,
and make radiotelephone calls to anywhere in the world through a marine operator.
Besides two-way communications, the radio can provide quick access to receive
all the N AA (National ceanographic and Atmospheric Administration) weather
channels and alert you to weather emergencies with a tone on a weather channel
you can select for your area.
R dio Controls
nd Indic tors
Introduction
Inst nt
Ch nnel
16/9 Button
Ch nnel
Up Button
ON/OFF/
Volume Control
Spe ker/
Microphone
Extern l Cover
Antenn
B cklit
LCD
Screen
Tri-W tch
Button
B ttery
B cklight/
Key Lock
Button
Memory/Esc pe
Button
Push to
T lk
Button
Ch nnel
Down
Button
Spe ker
Belt Clip
B ttery
Door
Screw
Power
Level/We ther
Button
SCAN Button
C ll/Enter
Button
VHF Microphone
MRHH350 ENG CVR vA F v8 MR HH 330 Cover 3/26/13 11:43 AM Page 1

MEMSAMEATISVOX LOMEDHI
ROG
VHF
T
R
A
B
GMRS
X
CIU
Introduction
Backlit LCD (Liquid Crystal Display) Screen •
UIC Active Ch nnel M p Icons
Button Lock Icon
Low/Medium/High
Power Icons
Power Settings
Selectable power settings produce
1, 3 or 6 watts of output power for
near or distant calling.
USA/International/Canada Channels
Allows operation on any of the three (3)
different channel maps established for
these areas.
All NOAA Weather Channels
Instant access to all National Weather
Channels, 24 hours a day.
Submersible to JIS7 Standards
Waterproof to 3.3 ft (1 m) of water
for 30 minutes.
Button/Key Lock
Prevents accidental setting changes
when button lock is set.
Channel Scan/Memory Scan
Use to scan through unlimited
channels or memory locations
to find conversations in progress.
Matrix Display
The display at the bottom of the LCD
screen will show text letting the user
know what mode, function or operation
the radio is currently in.
AA Battery Compatible
Good for emergency backup.
Requires optional AA battery tray
(P/N CM 110-024).
Instant Channel 16/9
Provides instant access to priority
Channel 16 and calling Channel 9.
Tri-Watch
Use to monitor three (3) channels
at once — Channel 16 and two (2)
programmable channels.
Floating
This radio will float if dropped overboard.
It has an orange stripe so it's easy to
retrieve. Must use included battery to float.
120 /12 Charger Included
Use to charge battery pack, at home,
in a car or in a boat.
Product Features •
B cklit LCD Screen
nd Product Fe tures Product Fe tures
Introduction
Locking Desktop Charger
Holds the radio or battery in place while
charging. Vertical or horizontal mounting.
Call Tones (Selectable)
10 selectable call tones
Emergency Weather Alert
Receive N AA alerts when threatening
weather is nearby.
Speaker/Mic Jack
Allows connecting optional Cobra
Lapel Speaker/Mic and other Cobra
accessories.
Unlimited Memory Channels
Allows programming of unlimited
VHF memory channels.
Signal Strength Meter
Shows the strength of incoming or
outgoing signals.
Illuminated Buttons
Allows high visibility of all function
buttons.
Roger Beep Tone (Selectable)
Confirmation tone indicates the
completion of the user’s transmission
and signals to others it is clear to talk.
n or ff selectable.
BURP
The Cobra exclusive BURP feature expels
water from the speaker grill if the unit is
dropped in the water or is subjected to
extreme rain and weather.
Product Features (continued) •
C ll Tone Icon
We ther Alert Icon
Frequency B nd Icon
Roger Beep Icon
B ttery Power Icon
Memory Icon
M trix Displ y
Simplex
Oper tion Icon
We ther Icon
Active Ch nnel
Tr nsmit nd
Receive Icons
Key Tone
Icon
Sign l Level
Icon
MRHH350 ENG CVR vA F v8 MR HH 330 Cover 3/26/13 11:44 AM Page 4

General Precautions
General Precautions •
The following WARNINGS and NOTICE information will make you aware of RF
exposure hazards and how to assure you operate the radio within the FCC RF
exposure limits established for the radio.
WARNINGS
Your radio generates electromagnetic RF (radio frequency) energy when it is transmitting.
To ensure that you and those around you are not exposed to excessive amounts of
that energy, DO NOT touch the antenna when transmitting. KEEP the radio at least
two (2) inches (5 cm) away from yourself and others when transmitting.
DO NOT operate with more than a duty cycle of 5% transmit, 5% receive and
90% standby. The radio is transmitting when the Talk button is pressed and the
transmit information shows on the LCD screen.
ALWAYS use only Cobra authorized accessories.
DO NOT operate the radio in an explosive atmosphere, near blasting sites,
or in any area where signs are posted prohibiting radio transmissions.
NEVER place the transceiver or microphone/speaker where they might interfere
with operation of your vessel or cause injury.
DO NOT allow children or anyone unfamiliar with proper procedures to operate
the radio without supervision.
Failure to observe any of these warnings may cause you to exceed FCC RF
exposure limits or create other dangerous conditions.
Introduction
Important Safety Information
Introduction
Important Safety Information •
Before installing and using your Cobra arine VHF radio, please read these
general precautions and warnings.
Warning and Notice Statements
To make the most of this radio, it must be installed and used properly.
Please read the installation and operating instructions carefully before installing
and using the radio. Special attention must be paid to the WARNING and NOTICE
statements in this manual.
WARNING
Statements identify conditions that could result in personal injury or loss of life.
NOTICE
Statements identify conditions that could cause damage to the radio
or other equipment.
Safety Training Information
This CobraMarine V F radio also complies with the following guidelines and
standards regarding RF energy and electromagnetic energy levels as well as
evaluation of those levels for human exposure:
■ FCC OET Bulletin 65 Edition 97-01 Supplement C, Evaluating Compliance with
FCC Guidelines for uman Exposure to Radio Frequency Electromagnetic Fields.
■ American National Standards Institute (C95.1-1992), IEEE Standard for Safety
Levels with Respect to uman Exposure to Radio Frequency Electromagnetic
Fields, 3 k z to 300 G z.
■ American National Standards Institute (C95.3-1992), IEEE Recommended
Practice for the Measurement of Potentially azardous Electromagnetic
Fields — RF and Microwave.
■ Industry Canada RSS-102-Radio Frequency (RF) Exposure Compliance of
Radiocommunication Apparatus (All Frequency bands).
Conformité d'exposition de la fréquence du Canada RSS-102-Radio d'industrie
(rf) de l'appareillage de communication par radio (toutes les bandes de
fréquence).
Introduction
Industry Canada Antenna Notice
Under Industry Canada regulations, this radio transmitter may only operate using an
antenna of a type and maximum (or lesser) gain approved for the transmitter by
Industry Canada. To reduce potential radio interference to other users, the antenna type
and its gain should be so chosen that the equivalent isotropically radiated power
(e.i.r.p.) is not more than that necessary for successful communication.
Avis d'antenne du Canada d'industrie
En vertu de la réglementation de l'industrie du Canada, cet émetteur de radio ne peut
fonctionner à l'aide d'une antenne d'un type et un maximum (ou moins) Gain approuvé
pour l'émetteur par Industrie Canada. Pour réduire le risque d'interférence aux autres
utilisateurs, le type d'antenne et son gain doivent être choisis afin que la puissance
isotrope rayonnée équivalente (PIRE) ne dépasse pas ce qui est nécessaire pour une
communication réussie.
350 VHF Body v8 MRHH330 ENG Body 3/26/13 11:45 AM Page 2

Introduction
FCC Licensing Information
Sea Tow Automated Radio Check (ARC) System
Please try the Sea Tow Automated Radio Check service. Areas where the safety check
service is available include the East Coast, Gulf of Mexico, and Southern California,
as well as in select inland regions. The first and only boating safety program of its
kind, the Sea Tow Automated Radio Check service is fully automated and allows 24
hour a day automatic responses to radio check calls.
Conducting a radio check through the Sea Tow Automated Radio Check service
couldn’t be simpler. All boaters need to do is tune their V F radios to Channel 24, 25,
26, 27 or 28, depending on the region, key the mic, and ask for a radio check. The
Automated Radio Check system responds to each radio check with an automated
reply, and also replays to the boater’s original radio transmission, allowing him or her
to assess the strength of the signal and confirm the V F radio is in good working
order.
To find the Sea Tow Automated Radio Check service channel in an area, owners
should visit http://www.seatow.com/arc. The web page links to an instructional video
demonstrating how to use the service step by step.
General Precautions
Introduction
NOTICE
Your radio is waterproof only when the batteries are properly installed.
AVOID using or storing the radio at temperatures below -4˚F (-20˚C) or above
140˚F (60˚C).
KEEP your radio at least 3 ft (0.9 m) away from your vessel’s magnetic
navigation compass.
DO NOT attempt to service any internal parts yourself. ave any necessary
service performed by a qualified technician.
This radio is supplied with a lithium-ion (LiON) rechargeable battery pack.
■Use only the Cobra charger to recharge lithium-ion (LiON) batteries in the radio.
■Do not short circuit the battery pack.
■When replacing the batteries, dispose of the old batteries properly. Batteries
may explode if disposed of in a fire.
Changes or modifications to your radio MAY VOID its compliance with
FCC (Federal Communications Commission) rules and make it illegal to use.
Recommendations for Marine Communication •
The frequencies your radio uses are set aside to enhance safety afloat and for vessel
navigation and operational messages over a range suitable for nearshore voyages.
If the 6 watt maximum output of your radio is not sufficient for the distances you travel
from the coast, consider a higher powered handheld or installing a Cobra Marine fixed
mount radio with up to 25 watts of output power. (Visit www.cobra.com or your
local dealer for model availability.)
If traveling far offshore, you should consider adding even more powerful radio
equipment such as F single side band or satellite radio for your vessel.
The U.S. Coast Guard does not endorse cellular telephones as substitutes for marine
radios. They generally cannot communicate with rescue vessels and, if you make
a distress call on a cellular telephone, only the party you call will be able to hear
you. Additionally, cellular telephones may have limited coverage over water and
can be hard to locate. If you do not know where you are, the Coast Guard will have
difficulty finding you if you are using a cellular telephone.
owever, cellular telephones can have a place on board where cellular coverage
is available — to allow social conversations and keep the marine frequencies
uncluttered and available for their intended uses.
Introduction
350 VHF Body v8 MRHH330 ENG Body 3/26/13 11:45 AM Page 4

Included in this Package
Included in this Packa e •
You should find all of the following items in the package with
your CobraMarine VHF radio:
FCC Licensing Information
International Station License
If your vessel will be entering the sovereign waters of a country other than the U.S.A.
or Canada, you should contact that country’s communications regulatory authority
for licensing information.
Radio Call Sign
Currently, the FCC does not require recreational boaters to have a license. The United
States Coast Guard recommends that the boat’s registration number and state of
registry (e.g., IL 1234 AB) be used as a call sign and be clearly visible on the vessel.
Canadian Ship Station License
You need a Radio Operator’s Certificate if your vessel is operated in Canadian waters.
Radio Operator training and certification is available from the Canadian Power
Squadron. Visit their website at http://www.cps-ecp.ca/.
User Responsibility and perating Locations
All users are responsible for observing domestic and foreign government regulations
and are subject to severe penalties for violations. The V F frequencies on your radio
are reserved for marine use and require a special license to operate from land,
including when your boat is on its trailer.
NOTE
This device complies with part 15 of the FCC Rules, and Industry Canada
license-exempt RSS standards. Operation is subject to the following two (2)
conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that
may cause undesired operation.
FCC Warnings: Replacement or substitution of transistors, regular diodes or
other parts of a unique nature, with parts other than those recommended by
Cobra may cause a violation of the technical regulations of part 80 of the FCC
Rules, or violation of type acceptance requirements of part 2 of the rules.
Introduction
16/9
TW
SCAN
WX
H M L
ESC
MEM
ENT SETUP
CALL
FLOATING
SUBMERSIBLE
MEM
SAMEATISVOXLOMEDHI
ROG
VHF
T
R
A
B
GMRS
X
CIU
MARINE HH350
Radio Drop-In Battery Charger
DC Charger
For connection to 12-volt power
sources.
Li N Battery Pack
perating Instruction Manual Spring-Loaded Belt Clip
Antenna
VHF Marine Radio Protocols
Installation
AC Charger
For connection to 120-volt power
source.
Wrist Strap
350 VHF Body v8 MRHH330 ENG Body 3/26/13 11:45 AM Page 6

Wrist Strap and Belt Clip
Install/Remove Antenna •
1. To install the antenna turn the antenna into the radio
clockwise to tighten. Do not overtighten
2. To remove the antenna turn the antenna counterclockwise.
This radio transmitter IC: 906A-MR 350 has been
approved by Industry Canada to operate with the supplied
antenna. Other antennas are strictly prohibited for use with
this device.
Cet émetteur radio IC: 906A-MR 350 a été approuvé par
Industrie Canada pour fonctionner avec l'antenne fournie.
D'autres antennes sont strictement interdits pour une
utilisation avec cet appareil.
Batteries and Char er •
The radio is shipped with a sealed lithium-ion (LiON) battery
pack (P/N CM 110-025) that is rechargeable.
WARNING
The charger provided for this radio is only to be used
to charge the battery pack provided. Do not charge
any other type of batteries in the charger as fire,
explosion or battery damage will occur. Avoiding
extreme room temperatures will also help prolong
the life of the battery pack for the radio.
When your rechargeable batteries begin to discharge too
quickly, it is time to install a new battery pack. Your radio
will also operate with five (5) high-quality AA alkaline
batteries, using the optional alkaline battery tray.
Installing the Battery Pack
1. Position the battery pack over the back of the radio.
2. Engage the battery pack into the radio by sliding to the top
until battery pack is fully seated against radio housing.
3. Tighten the screw using the end of the belt clip to secure
the battery pack to the radio. Do not overtighten. Only use
the end of the belt clip to tighten the screw.
Belt Clip
Insert Belt Clip onto Radio
16/9
TW
SCAN
WX
HM L
ESC
MEM
ENT SETUP
CALL
FLOATING MARINEHH350
MEMSAMEATISVOXLOMEDHI
ROG
VHF
T
R
A
B
GMRS
X
CIU
Secure Radio
VHF Marine Radio Protocols
Installation
Install/Remove Antenna
VHF Marine Radio Protocols
Installation
Antenna
Wrist Strap and Belt Clip •
Belt Clip
Use the spring-loaded belt clip to carry the radio on your
person.
1. Slide the belt clip into the guide channel on the back of the
radio until it is locked in place.
2. To attach the wrist strap, insert it through the hole at the
top of the belt clip, feed it through the looped end and pull
tight to secure to the belt clip.
3. Press open the belt clip, slide it over the belt and release
the clip.
4. To remove the belt clip from the radio press the tab on the
belt clip, which unlocks the clip, and slide it out.
Install Battery Pack
Li N Battery Pack
Tighten Screw
Wrist Strap Attachment
350 VHF Body v8 MRHH330 ENG Body 3/26/13 11:45 AM Page 8

VHF Marine Radio Protocols
Installation
To Remove Battery Pack from Radio
1. Loosen the screw on the back of the battery pack.
2. Lift the bottom of the battery pack slightly to remove
it from the radio housing.
3. Pull battery pack out of the radio housing.
NOTE
The LiON battery pack can also be charged in the
battery charger without being installed in the radio.
Insert the spacer into the battery charger to support
the battery pack during this charging process. Follow
the same procedures in “Initial Charge” to charge the
battery pack.
NOTICE
Lithium-ion (LiON) batteries are toxic. Please dispose
of properly. Some marine suppliers and electronics
retailers accept old battery
packs for recycling and
some municipal waste disposal
agencies have special
provisions for battery disposal.
Alkaline Batteries
An optional alkaline battery tray (P/N CM 110-024) can be
purchased for this radio. The alkaline battery tray acts as
a backup or “Emergency” power source should the battery
pack run low on power and needs to be recharged. The
radio will transmit at full power when using five (5) new
AA alkaline batteries.
WARNING
Never attempt to recharge alkaline batteries. They are
not made to be recharged, and should be disposed of
in a proper manner.
Batteries and Charger
VHF Marine Radio Protocols
Installation Batteries and Charger
Initial Charge
The Cobra-provided LiON battery pack may be charged at
home, in a car or in a boat using the appropriate 12V or
120V power cord with the charger.
1. Insert one (1) of the power cords into the back of the
drop-in charger.
2. Insert the other end of the power cord into the appropriate
12V or 120V power source.
3. Remove battery pack spacer from the charger and insert
the entire radio/battery into the charger. The metal charge
contacts on the battery will contact the mating prongs in
the charger to transfer the charging current.
4. Observe that the red light on the front of the charger
glows to indicate that the battery pack is properly seated
and the charger is operating.
5. Allow the batteries to charge for five (5) to six (6) hours
before use. The light will change back to green when the
battery is fully charged.
WARNING
Only the rechargeable LiON battery pack can be
recharged. You MUST use one of the charging devices
provided with this radio. Do not substitute any other
type of charging adapter or charger base for this
radio. Battery damage, fire or explosion may result.
It is equally important to prevent the lithium-ion
(LiON) battery pack from freezing to obtain best
performance from the battery pack.
NOTE
If the drop-in charger is used on a boat, Cobra
recommends you attach it to a horizontal shelf or
vertical bulkhead (using the screw holes provided)
to prevent possible damage due to the boat rolling or
pitching. The charging base has been designed to hold
the battery pack in place during rough sea conditions.
Remove Battery
Alkaline Battery Tray
Battery Pack Charging nly
Power Sources
Initial Battery Charge
350 VHF Body v8 MRHH330 ENG Body 3/26/13 11:45 AM Page 10

VHF Marine Radio Protocols
perating Your Radio Getting Started
Gettin Started •
Refer to the foldout at the front of this manual to identify the
various controls and indicators on your radio. Throughout
this manual you will be instructed to “Press” or to “Press
and old” various buttons (except “Push to Talk”) on the
radio. “Press” means a momentary press of approximately
one (1) second. “Press and old” means to hold the button
down for approximately two (2) seconds.
Whenever you press any button except the Talk button on
your radio, a brief tone (beep) (if key tones are selected On)
will sound to confirm the button press. With all button
presses, the appropriate icon will appear on the LCD and the
backlight will turn On. The backlight will stay On for 10
seconds after the button is released.
At times, you will hear two (2) other sounds. Two (2) beeps
will sound to confirm your setting changes and three (3)
beeps will sound to notify you of an error.
Common Radio Functions
The following procedures define common operating functions of the radio when in
either arine Standby or Weather (WX) Standby modes.
Power/Volume Control
Power On/Off Control
The On/Off/Volume control is located at the upper right
side of the radio. Turning the On/Off/Volume control
past the detent position will turn the radio On or Off.
Volume Control
Volume is controlled by turning the On/Off/Volume
control.
■To increase the volume, turn the On/Off/Volume
control clockwise.
■To decrease the volume, turn the On/Off/Volume
control counterclockwise.
Batteries and Charger
Maintaining the Battery Charge
As you use your radio, the battery power icon will show the
battery power remaining. When the icon begins to flash, it is
time to recharge or change the batteries.
NOTE
Radio will continue to receive signals when blinking
but cannot transmit.
NOTICE
Use only the drop-in charger provided by Cobra. Do
not use the charger with alkaline batteries; only the
LiON battery pack is rechargeable. Spent alkaline
batteries must be discarded and replaced.
It is a good idea to keep a set of fresh, high-quality AA
alkaline batteries with your radio. Should the rechargeable
battery pack become discharged and no electrical power
source is available, you can insert the optional alkaline
battery tray with fresh alkaline batteries and continue to
use your radio.
n/ ff/Volume Control
(Counterclockwise)
n/ ff/Volume Control
(Clockwise)
16/9
TW
SCAN
WX
H M L
ESC
MEM
ENT SETUP
CALL
FLOATING
SUBMERSIBLE
MEMSAMEATISVOXLOMEDHI
ROG
VHF
T
R
A
B
GMRS
X
CIU
MARINEHH350
HH350 Radio
Fully Charged
Partially Charged
Fully Discharged
VHF Marine Radio Protocols
Installation
350 VHF Body v8 MRHH330 ENG Body 3/26/13 11:45 AM Page 12

VHF Marine Radio Protocols
perating Your Radio Getting Started
Channel Up/Down Buttons
Your radio will Receive (Rx) and Transmit (Tx) V F signals
on the channel indicated on the LCD display. You can change
the channel at any time using the Channel Up/Down buttons.
To Change Channels:
Press the Channel Up/Down button.
If you are on Channel 88, pressing the Channel Up
button will advance to Channel 01. If you are on
Channel 01, pressing the Channel Down button will
advance to Channel 88.
You can press and hold the Channel Up/Down button
for fast advance. The beep sound will occur only at the
first press of the button and not during fast advance.
If the new channel selected is restricted to low power,
the radio will automatically switch to Low Power mode
and the Low Power icon will appear on the LCD.
If the radio is in the Key Lock mode, the channel will
not change and the three (3) beep error signal will sound.
SCAN Button
Press and release the SCAN button to scan all channels. The
SCAN icon will display on the LCD display. Scanning begins
at lower channels, and scans to higher channels. Press the
Channel Up/Down button to change the scan direction.
When a signal is received in SCAN mode, the radio will pause
10 seconds before resuming SCAN operation. The scan will
stop on the paused channel and remain there when the Talk
button is pressed.
In emory mode, press and release the SCAN button to
scan all memory channels. Because the unit is already in the
emory Channel mode, only the channels in the memory
bank will be displayed.
NOTE
Memory channels need to be saved to effectively
enter the emory Channel mode and scan all
memory channels.
SCAN
ESC
MEM
SCAN Button
ENT SETUP
CALL
FLOATING MARINE HH350
Channel Up/Down Buttons
SAMATISVOX LOMEDHI
T
R
A
B
X
CIU
Currently n Channel 88
VHF Marine Radio Protocols
perating Your Radio Getting Started
Radio Speaker and Microphone
The internal Radio Speaker and icrophone are located on the
bottom front face of the radio below the lower control buttons.
An optional Speaker/ icrophone port is located at the top
of the radio between the antenna and the Power/Volume
control. Unthread the Speaker/ icrophone port cover to access
and install an optional Cobra speaker or microphone into this port.
Talk Button
Press and hold the Talk button to transmit messages.
Release the Talk button to stop transmitting.
Backlight/Key Lock Button
To Display the Backlight omentarily:
Press the Backlight/Key Lock button. The backlight will
remain On for 10 seconds. If the backlight is already
On, another press of the Backlight/Key Lock button
will turn it Off.
Key Lock
To prevent accidental changes to your settings, you can
lock all of the following buttons:
■Channel Up Button
■Channel Down Button
■SCAN Button
■E /ESC Button
■WX/H- -L Button
■16/9 Button
■TRI-WATCH Button
■Call/Enter/Setup Button
To Lock or Unlock the Buttons:
Press and hold the Backlight/Key Lock button for two
(2) seconds. The Key Lock icon will appear or disappear
in the LCD. When Key Lock is On, pressing any of the
listed buttons on the front of the radio will result in a
three (3) beep error message.
Both the Backlight/Key Lock button and the Talk button
are active — you can Receive (Rx) or Transmit (Tx)
a message with Key Lock On, but you cannot change
the channel.
Backlight/Key Lock Button
16/ 9
TW
SCAN
WX
HML
ESC
MEM
ENT SETUP
CALL
FLOATING
SUBMERSIBLE
MEMSAMEATISVOX LOM E D H I
ROG
VHF
T
R
A
B
GMRS
X
CIU
MARINE HH350
Key Locked Buttons
VHF
GMRS
Key Lock Icon
Speaker/Mic Port
Talk Button
350 VHF Body v8 MRHH330 ENG Body 3/26/13 11:45 AM Page 14

VHF Marine Radio Protocols Setup Mode Programming
Setup Mode Pro rammin •
The following series of procedures is designed to allow you
to set the programmable features of your radio. Correctly
following these steps results in a minimal amount of radio
setup programming time.
During setup programming, the matrix display will show text
describing the programming action you are now performing.
NOTE
When in the Setup mode, if you stop programming for
longer than 15 seconds,
your entry will be saved and
the radio will go back to the arine Standby mode.
When you return to Setup mode and continue
programming you will see the last “value” displayed.
While in the Setup mode, you will not receive any
signal reception except when setting squelch.
Programming these features will allow you to customize
certain features of this radio to enhance your “On-Water”
radio use.
Start from arine Standby mode to begin arine (VHF)
Setup programming. STANDBY will be displayed on the
matrix. Press and hold the Call/Enter/Setup button for two
(2) seconds to enter the programming mode.
The mode programming follows this sequence:
■Squelch Level Set
■UIC Channel Map
■Tone Alert On/Off
■Call Tone Select
■Roger Beep On/Off
■Key Tone On/Off
Marine (VHF) Mode Programming
VHF Marine Radio Protocols Getting Started
High/Medium/Low (H-M-L) Power Button
Your radio can transmit selectively at 1, 3 or 6 watts of
power. Cobra suggests you maintain the low power setting
for short-range communications. You will conserve battery
life and avoid overpowering nearby stations with a low power
setting signal. Use the high power setting for long-range
communications or when you do not receive a response to
a signal sent at 1 watt.
To Toggle Between H- -L Power odes:
Press the H- -L Power button. The LCD will show
which mode is in effect. Some channels are restricted
for a maximum use of 1 watt. Your radio will
automatically set the power to Low Power mode
when you select those channels.
NOTE
Some channels, frequency bands and countries of use
might not be able to operate in High Power mode.
Call/Enter/Setup Button
NOTE
A few channels are Receive only and will not transmit
in these channels.
The Call/Enter/Setup button has multiple functions. It is
generally used in the following ways:
■Press and release to transmit your unique Call Tone signal
to another radio.
■Press and hold to enter any Setup menu.
■Functions as an Enter button when making a selection
in any Setup menu.
WX
HM L
SC
EM
H-M-L Power Button
MEM
ENT SETUP
CALL
Call/Enter/Setup Button
perating Your Radio
perating Your Radio
MEMSAMEATISVOX LO MEDHI
VHF
T
R
A
B
GMRS
X
CIU
Marine Standby Mode
350 VHF Body v8 MRHH330 ENG Body 3/26/13 11:45 AM Page 16