Cockpit CKNOLIN User manual

USER MANUAL EN.
Cockpit Camera
Add/Remove User Manual
Before starting adding your module, please complete set up procedure
for your COCKPIT gateway.
For more information about COCKPIT gateway set up procedure, please
refer to the COCKPIT gateway User Manual.
Type: Camera Date: 05.04.2019
Ordering code: CKNOLIN Document: COCKPIT_Camera_Indoor_Add.Rem_v1_eng 1

5. Select “Configure camera”
option.
Adding Camera
1
2
4
5
6
2
1. Click “Home Setup” tab
located in the bottom of
Cockpit@Home app.
2. Click „Manage devices”.
3. For LAN connection, connect
camera to the router using
LAN cable and go to the item
14. For WiFi connection,
please proceed to the next
step.
4. Click gear button on the top
of the screen.
6. Select “Tutk”.

9. Type in SSID and Passkey
of your WiFi network.
10. Press arrow button on the
bottom of the screen
7. Position IP camera not more
than 5 meters from WiFi router
and power up the camera. Wait
for camera to rotate and starts
to play Ding-Dong tone in a loop.
8. Press arrow button on the
bottom of the screen.
8
13
3
10
11. COCKPIT gateway will start
WiFi configuration procedure.
12. When the camera have been
connected to the WiFi
network, “Ding-dong” sound
will stop and appropriate
information will appear on the
screen.
13. Press arrow button to proceed.

14
15
18
4
14. When network connection
is set (WiFi or LAN), camera
can be added to the system.
Click gear button on the top
of the screen.
15. Select “Find devices”
option.
16. COCKPIT gateway will start
“Add new devices mode”.
17. After adding process
complete, the list of devices
appears with Camera
present on it.
18. Click on “settings” icon
located next to the Camera
module name.

19. Select “Edit” option. 21. You will be directed back to
the screen where you can see
all added devices. Adding
procedure for Camera
module is now completed.
Press arrow button and you
will be directed to “Home
Setup” screen.
21
5
20
20. Name the device (e.g. Indoor
IP Camera) and select room
(e.g. Living Room) for the
camera module. When you are
done, click “DONE” button.
22. To locate newly added
device, click “Devices” tab on
the bottom of the screen.
23. If device is not shown on the
list, choose the proper room
by pressing „Device by
location” button.
22
23
19

4. Select “Delete” option.
Removing Camera
1
2
3
5
4
6
1. Click “Home Setup” tab
located in the bottom of
Cockpit@Home app.
2. Click „Manage devices”
button.
3. Click on “settings” icon
located next to the Camera
module name.
5. Click “OK” to confirm deleting
camera from the system.

6. Information window, confirming
deleting device from the
network will appear. Click “OK”
to continue.
8. Removing procedure for
Camera module is now
completed. You will be
redirected to “Home
Setup” screen.
6
7
7
7. You will be directed back to the
screen with list of devices,
where Camera module is not
present anymore.
Press arrow button to proceed. * Please remember, that in case of WiFi connection, the camera
module is still connected to your WiFi network. To disconnect
module from the WIFi network, please restore camera to the
factory state by holding “Reset” button for 5s.

COCKPIT Smart Home d.o.o. Nova Gorica
Ulica Klementa Juga 007
5250 Solkan
Slovenia
E-mail: [e-mail]
Tel: [phone]
Fax: [phone]
Web: www.yourcockpit.biz
8