Code Corporation CodeXML User manual

Keyboard Input (USB & PS2)
The modem is defaulted to English language keyboards. If you need to
communicate in a different language requiring a change in keyboard
settings, please scan the appropriate code below:
English (Default) Universal French German
Non-printable ASCII Keyboard Non-printable ASCII
Japanese (No Leading 0 Keyboard (Crtl + character)
2 C003345_01_CodeXML_Modem_Quickstart C003345_01_CodeXML_Modem_Quickstart 3
CodeXML Modem Installation with USB Cable
Figure 4
Figure 5
Figure 3
CodeXML Modem Installatin with PS2 Cable
Cable Installation
Attach the end of the USB cable to the CodeXML Bluetooth Modem (Figure 2).
Connect the USB connector to the host computer (Figure 3). Once connected
the modem’s blue LED light will turn on.
Figure 2
Connecting with QuickConnect Code
See instructions below for establishing a paired connection between the modem
and the host computer.
Establish Mode
Scan the USB Mode code (M708_01-right). You are ready to
begin reading bar codes and transmitting decoded data to the host
computer.
USB Cable installed to CodeXML Modem
USB Mode
Connecting with QuickConnect Code (for all cable types):
Scan the QuickConnect Code on the label of the CodeXML Bluetooth Modem
using the Code reader with which you wish to establish a paired connection to a
host computer. The reader and host computer should easily connect within
60 seconds. The Code reader will beep once and flash both LEDs green
as confirmation. If the reader and computer do not connect, the reader
will beep three times in rapid succession and flash red LEDs.
Modem Firmware Version Output & Values (for reference only):
Cable Installation
Attach the end of the PS2 cable with the
single connector to the CodeXML Modem
(Figure 2 - left). Detach the keyboard from the
host computer and connect it to the same type
connector on the PS2 cable (Figure 4).
Connect the other cable end to the host computer (Fig-
ure 5). The modem is powered by the PS2 port and
does not require a power supply (You must be running
firmware 2098 or higher on your reader - see below
left for scan code to determine firmware version). Once
connected the modem’s blue LED light will turn on.
Connecting with QuickConnect Code
See instructions below for establishing a paired con-
nection between the modem and the host computer.
Establish Mode
Scan the PS2 Mode code (M660_01-right).
You are ready to begin reading bar codes
andtransmitting decoded data.
PS2 Cable installed to CodeXML
Modem & Keyboard
PS2 Mode
VVVVvvvvCKP BaudString:
VVVV 4 digit firmware version (MSP430 firmware version)
vvvv 4 digit firmware version (TUSB firmware version)
C 1 digit comm mode: 0=PS/2, 1=Serial, 2=Wand Emul., 3=USB KBD
K Keyboard Map, same as reader host ICD setting 0x2d
P 1 digit packet protocol: 0=Raw, 1=SPX packet, 2=Code Reader
packet, 4=Encrypted Packet Format, 5= Protocol Version (AES)
BaudString spx: Baud:DataBitsParityStopbits
For All Readers:
Scan to View
Firmware Version

Quickstart Guide
4 C003345_01_CodeXML_Modem_Quickstart
CodeXML Modem -
Multiple Interface Unit (MIU)
C003345_01_CodeXML_Modem_Quickstart 1
CodeXML Modem Installation with RS232
The CodeXML MIU Modem is an external modem designed to be
connected to the host computer in use with a Code reader (CR2 or
CR3). The Modem enables a reader to wirelessly transmit captured and
decoded data to its host computer. The Modem can accommodate cabled
attachment with three connector types (Figure 1).
Figure 1
The CodeXML MIU Modem is ‘plug & play.’ You simply plug-in the Modem
and start transmitting data from Code readers without downloading any
drivers or software. The Modem can receive Bluetooth signals from up to
300 feet (100 meters) away.
For assistance, contact Code Technical Support at: 801 495 2200; or by
email: [email protected]
Cable Installation
Attach the end of the RS-232 cable (pictured below) to the CodeXML Bluetooth
Modem (Figure 7). Connect the RS-232 adapter to the back of your computer
(Figure 8). Connect the RS-232 cable to the power supply (Figure 9). Plug the
power supply into a wall socket (Figure 10). Once connected the Modem’s blue
LED light will turn on.
Figure 7 Figure 8 Figure 9 Figure 10
RS232 Cable (Left) - CodeXML Modem
(Center) - Power Supply (Right)
Connecting with QuickConnect Code
See Page 2 for instructions to establish a paired
connection between the Modem and the host
computer.
RS232 Mode
Establish Mode
Scan the RS232 Mode code (M661_01-right).
You are ready to begin reading bar codes and
transmitting decoded data to a host computer
with any open software application that
accepts data from RS232/Serial input.
CodeXML Modem MIU
Change Baud Rate Settings: Scan the
appropriate code below:
Note: These codes only affect Baud Rate for the
modem and do not affect any settings on Code Readers.
1200 2400 4800 9600 (Default)
19200 38400 57600 115200
Default Modem
settings:
Baud Rate: 9600
Stop Bits: 8
Parity: None
Stop Bits: 1
Hardware: None