Coinco Money Controls MC Series User manual

MC Series Bill Acceptors
Installation Guide/Application Data
Operational Specifications
Product Features
• Bill widths accepted: MC2600 (66mm), MC7200 (72mm)
• Operating Voltages: 110VAC, 24VAC, 24VDC, 12 VDC
• Communication Interface: MDB, Pulse, Vend Serial, ccTalk,
ICT serial over RS232.
•Four-Way Acceptance
• Mounting: Upstack or Downstack
• Lighted Bezel (on standard mask only)
• Coupon capable
• Superior Stringing Protection
Operating Temperature Range: 0oF - 150oF
Storage Temperature Range: -22oF - 160oF
Input Power Requirements:
Bill Acceptance:
120 VAC 90-135VAC @1.0A
24VAC 20-32VAC @1.5A
24VDC 20-45VDC @1.5A
12VDC 10-14VDC @4A
Page 1
US $1 $5 $10 $20
CAD $5 $10 $20 $50 $100
EURO €5 €10 €20
RUR 5 10 50 100 500 1000

Bill Inlet Width
26 = 66mm
72 = 72mm
Bezel
0= See “Build”
1= Standard
2 = Slimline
Input Voltage/Protocol
1= 110VAC- Pulse, Vend Serial
2 = 24 VDC/AC MDBPulse
3= 12 VDC - Multi-Interface
4= 12 VDC - MDBWake/Sleep
MountingConfiguration
U= Up
D= Down
Cashbox Size
0= See “Build”
3= 300 Bills
5= 500 Bills
7 = 700 Bills
9= 900 Bills
B= 1100 Bills
N= None
I/O Harness
A= 110 VAC Power
C= 24VAC Power
M= MDB
I= Multi-Interface
W= Wake/Sleep
Build
00 = Standard
CountryCode
001 = Argentina
002 = Australia
005= Brazil
006 = Canada
014= Germany
041= United States
050= China
070= Euro
030= Russia
MC Series Model Naming Convention
MC x x x x x x x x x x x x
Page 2
Figure 1

Unpacking:
After unpacking the unit, inspect for any possible shipping damage. If
damaged, notify the shipping company immediately. Keep the carton
and packing material to reuse if you need to transport or ship the
changer in the future. Labels indicating the model and serial number
are on the side of the bill acceptor. Refer to these numbers when call-
ing upon your Coinco Service Center representative for information or
service.
Bezel Types
Page 3
Figure 2: Slimline Bezel Figure 3:Standard Bezel

Installation
NOTE: The Metal mounting plate must be connected to earth
ground.
1. Remove power from host machine.
2. Set bill acceptor dip switches, if required. (see Page 5).
3. Install the bill acceptor into the host machine using the mounting
studs and hardware in the machine.
4. Install / Connect the proper interface harness to the host machine.
5. Apply power to the machine, verify that the Green Flashing Arrows on
the front of the bill acceptor (with standard mask) are ON and blink-
ing. This condition indicates that the bill acceptor is ready to accept
bills.
• If the Lights are off, check connections and make sure power is
applied.
• Also check the rear diagnostic LED, the status codes are listed on
the cashbox and in the figure below.
6. Check Operation, once the Green Arrows are flashing, insert bills to
verify proper acceptance and credit.
Diagnostic LED
# of LED Flashes LED Status
Normal Pulse Rate
1 pulse per second
Ready
Fast Pulse Rate
3 pulses per second
Check Stacker/Cashbox
Not Lit Check Power
Steady ON Replace Acceptor
2 Flashes Bill Inhibited
3 Flashes Disabled by Host
4 Flashes Clear Bill Path
5 Flashes Clean Bill path
Page 4

Page 5
Dip Switch Configuration
OFF
ON
ON
OFF
1234 567 8
Front of MC Series Acceptor
PC Board
Figure 4
Dip Switch Locations
and Position
US Dip Switch ON/OFF Canadan Dip Switch ON/OFF Euro Dip Switch ON/OFF Russian Dip Switch ON/OFF
Switch 1 $1 enable/disable $10 enable/disable €5 enable/disable RUR 50 enable/disable
Switch 2 $5 enable/disable $20 enable/disable €10 enable/disable RUR 100 enable/disable
Switch 3 $10 enable/disable $50 enable/disable €20 enable/disable RUR 500 enable/disable
Switch 4 $20 enable/disable $100 enable/disable RESERVED RUR 1000 enable/disable
Switch 5 4Pulse / 1 Pulse per $1 RESERVED RESERVED Pulse / ICT Serial
Switch 6 Always / Harness enabled RESERVED RESERVED Short Pulse / Long Pulse
Switch 7 Short Pulse / Long Pulse RESERVED RESERVED 2 Pulse / 1 Pulse per RUR 10
Switch 8 Coupon enable/disable Coupon enable/disable RESERVED Always/Harness enabled

Cash Assess Door
Lift door to remove
cash
Cash Box
To Remove Bottom
Sensor Housing
(Access Bill Path)
Upstacking--
Push red latch down and
pull straight back
To Remove Cash Box
Upstacking--
Push red latch on top
forward. Lift up and back.
Interface
Connector
Standard
Bezel
Bill Entrance
Metal Mounting Plate
must be connected to
earth ground.
Diagnostic LED
Bottom Sensor Housing
MC2600/7200 Description
NOTE: The metal mountaing plate must be connected to earth
ground.
Page 6
Figure 5

Maintenance
Recommended Cleaning Material:
A mild solution of detergent can be used for cleaning the belts, bill path
and sensor lenses, as well as for general cleaning of the acceptor.
Beverages or other water-soluble liquids which have been spilled on or
into the acceptor can usually be removed with warm soapy water.
External surfaces can be cleaned with a damp cloth.
Note: Petroleum-based cleaners and freon-based propellants can dam-
age plastic and some electronic componenets. Scouring pads and stiff
brushes may harm the circuit boards and can mar the plastic. These
items should never be used when cleaning the bill acceptor.
Cleaning the Optical Sensor Lenses and Gray Scales
Warning: Remove power from the bill acceptor before opening the
bill path.
Remove the cash box and bottom sensor housing from the acceptor. To
clean the optical sensor lenses and gray scales use a "Lint Free" cloth
with a mild detergent. Repeat the cleaning process as needed until all
the sensor surfaces are free of contaminants. Remember to clean both
sensor lenses.
Page 7
Gray Scales
Bottom Sensor
Housing
Acceptor
(Cashbox removed)
Optical Sensor
Lens
Figure 6

Page 8
Figure 7: MC2600 Dimensional Drawing
(Up Stacking Position)

Page 9
Figure 8: MC7200 Dimensional Drawing
(Up Stacking Position)

Page 10
Figure 9: MC7200 Dimensional Drawing
(Up Stacking Position)

Interface Connectors
Page 11
Pin #
MCxxx2 (24VAC/VDC) MCxxx1 (110VAC) MC72x3 (12VDC) MC72x4
(12VDC with MDB wake)
1CREDIT_RELAY_COMMON CREDIT_RELAY_COMMON CREDIT_RELAY_NO NOT USED
2CREDIT_RELAY_NO NOT USED 12VDC 12VDC
324VAC_HOT NEUTRAL_ENABLE CREDIT_RELAY_COMMON NOT USED
4HOT_ENABLE 110VAC_NEUTRAL DC_RETURN DC_RETURN
5KEY NEUTRAL_INHIBIT SIGNAL_GROUND SIGNAL_GROUND
6MDB_MASTER_RXKEY CCTALKNOT USED
7TX_232TX_232A2_EN/CCTALK_EN*NOT USED
8INTERRUPT*INTERRUPT*MDB_COM MDB_COM
9CCTALKCCTALKMDB_MASTER_TXMDB_MASTER_TX
10 SIGNAL_GROUND SIGNAL_GROUND MDB_MASTER_RXMDB_MASTER_RX
11 DATA*DATA*RX_232NOT USED
12 ESCROW_HIGHESCROW_HIGHESCROW_LOWNOT USED
13 232_EN/CCTALK_EN*232_EN/CCTALK_EN*ESCROW_HIGHNOT USED
14 MDB_MASTER_TXNOT USED TX_232MDB_WAKE
15ACCEPT_ENABLE_HIGHACCEPT_ENABLE_HIGHACCEPT_ENABLE_HIGHNOT USED
16DC_RETURN CREDIT_RELAY_NO ACCEPT_ENABLE_LOWNOT USED
17 NEUTRAL_INHIBIT NOT USED
18NEUTRAL_ENABLE HOT_ENABLE
19NOT USED KEY
20 24VAC_NEUTRAL 110VAC_HOT
21 KEY EARTH_GROUND
22 OUT_OF_SERV*OUT_OF_SERV*
23 MDB_34VDC NOT USED
24 ACCEPT_ENABLE*ACCEPT_ENABLE*
25OUT_OF_SERV_POWER OUT_OF_SERV_POWER
26SEND*SEND*
27 ACCEPT_ENABLE_LOWACCEPT_ENABLE_LOW
28MDB_SIGNAL_COM NOT USED
29RX_232RX_232
30 ESCROW_LOWESCROW_LOW
30 Pin Mating Connector
Receptacle Housing AMP 1-104482-3
Receptacle Pins AMP 104479-2
Receptacle Polarizing Pins AMP 87077-2
16 Pin Mating Connector
Polarized Receptacle Housing VENSIK 5000-PAI-2x08
Receptacle Pins VENSIK 4000-T-PS-T
8Pin Download/Diagnostics Mating Connector
Polarized Receptacle Housing AMP 87631-3 or 2-87977-9 Money Controls 35x816-8
Receptacle Pins AMP 85969-9 or 86016-3 Money Controls 35x245
Pinouts

Note: Pin 21 Ground of the 30 pin power connector and the
metal mounting plate must be connected to earth ground
MC2600/MC7200 Pulsed Interface Connections
for 30 Pin 110VAC
Page 12
Figure 10

2
2R
1
1
1
R
Note: Pin 21 Ground of the 30 pin power connector and the
metal mounting plate must be connected to earth ground
MC2600/MC7200 Vend Serial Interface Connections
for 30 Pin 110VAC
Page 13
Figure 11

MC2600/MC7200 RS232 Interface Connections
for 30 Pin 24VAC/VDC
Page 14
Figure 12

3
MC2600/MC7200 MDB Interface Connections
for 30 Pin 24 VAC/VDC
Page 15
Figure 13

K
MC2600/MC7200 Pulsed Interface Connections
for 30 Pin 24 VAC/VDC
Page 16
Figure 14

Page 17
Available Harnesses
CA/MC Harness part number Used with MC model number Description
WMH/455 MC72x4 16 pin to MDB
WMH/549 MC72x3 16 pin to MDB (with diode)
925892 MC72x3 16 pin to Pulsed and 232 Serial
T.B.D. by Money Controls Royton MC72x3 16 pin to ccTools Diagnostics
925930 MCxxx2 30 pin to MDB
925931 MCxxx2 30 pin to 24VAC Pulsed
925932 MCxxx1 30 pin to 110VAC Pulsed

Technical Support-Contact Information
USA
Coin Acceptors, Inc.
Phone: [phone]
Email: [email protected]
Web Site: www.coinco.com
CANADA
Coin Acceptors Canada
Phone: [phone]
Email: [email protected]
Web Site: www.coinco.com
Or contact your local Coinco Distributor or Service Center.
Europe
Coin Acceptors LTd.
United Kingdom
Phone: T+44 1342 315724
Coin Acceptors GmbH
Germany
Phone: T+49 2154 205000
Coin Acceptors Sarl
France
Phone: T+33.1.56.48.05.05
Page 18

Page 19
This page is left intentionally blank.

Coinco Publication #925xxx
03/2005 Printed in the USA
Coin Acceptors, Inc.
300 Hunter Avenue
St. Louis, MO 63124-2013
314 725-0100
[phone]