COLDWAVE MPPD-12CRN1 User manual

COLDWAVE
Portable Air Conditioner
Model
MPPD-12CRN1
12000 BTU/h
110V/1Ph/60Hz
R410A

Features:
4 Speed Fan
Ion Generator
Sleep Mode
Timer
Auto/Cool/Dry Mode
Swing Function
Follow Me Temperature Sensor
Swing Button
LED Display
Note: Cooling Only, No heat function.

1. DIMENSION
H
W
D
Unit Dimension
W
H
D
mm(inch)
Single-hose
454(17.9)
700(27.6)
365(14.4)
(small body)
Single-hose
467(18.4)
765(30.1)
397(15.6)
Double-hose
467(18.4)
765(30.1)
478(18.8)

2. OPERATION MODES AND INSTRUCTIONS
98Optional
76544321
2.1 OPERATION MODES
POWER BUTTON 1
Power switch on/off.
SLEEP/ECO BUTTON 2
Used to initiate the
SLEEP/ECO operation.
NOTE: On some models SLEEP
button is instead of ECO button.
FAN/ION BUTTON (ION
is optional) 3
Control the fan speed. Press to select
the fan speed in four steps-LOW,
MED, HI and AUTO.The fan speed
indicator light illuminates under
different fan settings except AUTO
speed. When select AUTO fan speed,
all the fan indicator lights turn dark.
NOTE: Press this button for 3 seconds to
initiate ION feature.The ion generator is
energized and will help to remove pollen
and impur ities from the air, and trap
them in the filter. Press it for 3 seconds
again to stop the ION feature.
UP(+) AND DOWN(-) BUTTON
4
Used to adjust (increasing/
decreasing)
temperature settings
(2
1 increments) in a range of
62
(17
) to 88 (30 ) or the
TIMER setting in a range of
0~24hrs. NOTE:
The control is capable of displaying
temperature in degrees Fahrenheit
or degrees Celsius. To convert
from one to the other, press and
hold the Up and Down buttons at
the same time, for 3 seconds.
MODE SELECT BUTTON 5
Selects the appropriate operating mode.
Each time you press the button, a mode
is selected in a sequence that goes from
AUTO, COOL, DRY, FAN and HEAT
(cooling only models without).
The mode indicator light illuminates
under the different mode settings..

TIMER BUTTON 6
Used to initiate the AUTO ON start
time and AUTO OFF stop time
program, in conjuction with the (+)
& (-) buttons. The timer on/off
indicator light illuminates under the
timer on/off settings.
SWING BUTTON 7
(Applicable to the models with
auto swing feature only)
Used to initiate the Auto swing
feature. When the operation is ON,
press the SWING button can stop
the louver at the desired angle.
LED DISPLAY 8
Shows the set temperature in " " or
"" and the Auto-timer settings.
While on DRY and FAN modes, it
shows the room temperature.
FOLLOW ME/TEMP SENSING
(OPTIONAL)
9
NOTE:This feature can be activated
from the remote control ONLY.
The remote control servesas a
remote thermostat allowing for the
precise temperature control at its
location. To activate the Follow
Me/Temp Sensing feature, point the
remote control towards the unit and
press the Follow Me/Temp Sensing
button. The remote display is actual
temperature at its location. The
remote control will send this signal
to the air conditioner every 3
minutes interval until press the
Follow Me/Temp Sensing button
again.If the unit does not receive the
Follow Me/Temp Sensing signal
during any 7 minutes interval, the
unit will beep to indicate the Follow
Me/Temp Sensing mode has ended
2.2 OPERATION INSTRUCTIONS
COOL OPERATION FAN OPERATION
Press the "MODE" button until the
"COOL" indicator light comes on.
Press the ADJUST buttons "+" or " -
" to select your desired room
temperature. The temperature can be
set within a range of 62 -88 17 -30 .
Press the "FAN SPEED"
button to choose the fan speed.
Press the "MODE" button until the
"FAN " indicator light comes on.
Press the "FAN SPEED"
button to choose the fan speed.
The temperaturecannot be adjusted
Do not put the duct to window.

HEAT OPERATION
(cooling only models without)
Press the "MODE" button until the
"HEAT" indicator light comes on.
Press the ADJUST buttons "+" or "
- " to select your desired room
temperature. The temperature can be
set within a range of 62 -88 17 -30 .
Press the "FAN SPEED" button to
choose the fan speed. For some
models, the fan speed can not be
adjusted under HEAT mode.
Press the "MODE" button until the
"DRY" indicator light comes on.
Under this mode, you cannot select a
fan speed or adjust the temperature.
The fan motor operates at LOW speed.
Keep windows and doors closed
for the best dehumidifying effect.
Do not put the duct to window.
AUTO OPERATION
When you set the air conditioner in
AUTO mode, it will automatically
select cooling, heating(cooling only
models without), or fan only
operation depending on what
temperature you have selected.
and the room temperature.
The air conditioner will control room
temperature automatically round the
temperature point set by you.
Under AUTO mode, you can not
select the fan speed
TIMER OPERATION
When the unit is on, press the
Timer button will initiate the Auto-
off stop program, the TIMER OFF
indicator light illuminates. Press
the UP or down button to select the
desired time. Press the TIMER
button again within 5 seconds, the
Auto-on start program is initiated.
And the TIMER ON indicator light
illuminates. Press the up or down
button to select the desired Auto-on
start time.
When the unit is off, press the
Timer button to initiate the Auto-
on start program, press it again
within five seconds will initiate
the Auto-off stop program.
Press or hold the UP or DOWN
button to change the Auto time by
0.5 hour increments, up to 10 hours,
then at 1 hour increments up to 24
hours. The control will count down
the time remaining until start.
The system will automatically
revert back to display the previous
temper-ature setting if there is no
operation in a five seconds period.
Turning the unit ON or OFF at
any time or adjusting the timer
setting to 0.0 will cancel the
Auto Start/ Stop timer program.
When the malfunction (E1,E2,E3
or E4) occurs, the Auto Start/Stop
timed program will also be cancelled.

SLEEP OPERATION
Press this button, the selected temperature will increase(cooling) or
decrease(heating) by 2 1 30 minutes.The temperature will then increase
(cooling) or decrease (heating) by another 2 1 after an additional 30
minutes. This new temperature will be maintained for 7 hours before it
returns .to the originally selected temperature. This ends the Sleep mode
and the unit will continue to operate as originally programmed.
NOTE: This feature is unavailabe under FAN or DRY mode.
3. ELECTRONIC FUNCTION
3.1 Abbreviation
T1: Indoor room temperature.
T2: Temperature of evaporator.
T3: Temperature of condenser.
TS: The setting temperature.
S1: Water level swicth
3.2 Main Protection
3.2.1 The compressor functions protection with a delay of three minutes.
Compressor will restart with a delay of three minutes once it stops
operation.But it is four minutes delay for Heat pump model’s restarting.
3.2.2 Sensor protection at open or short circuit. A/D
≤2 Ω, Sensor protection at open circuit;
A/D≥253Ω, Sensor protection at short circuit.
(Table A in next page show you the relation between
temperature and resistance of sensor.)
3.2.3 .
At cooling or drying mode,when T2 ≤2
≥10

TABLE A:
CHARACTERISTIC OF TEMPERATURE SENSOR
Temp.
Resistance
Temp.
Resistance
Temp.
Resistance
℉/℃
KΩ
℉/℃
KΩ
℉ / ℃
KΩ
-
-
62.6/17
14.6181
111.2/44
4.3874
15.8/-9
58.7079
64.4/18
13.918
113/45
4.2126
17.6/-8
56.3694
66.2/19
13.2631
114.8/46
4.0459
19.4/-7
52.2438
68/20
12.6431
116.6/47
3.8867
21.2/-6
49.3161
69.8/21
12.0561
118.4/48
3.7348
23/-5
46.5725
71.6/22
11.5
120.2/49
3.5896
24.8/-4
44
73.4/23
10.9731
122/50
3.451
26.6/-3
41.5878
75.2/24
10.4736
123.8/51
3.3185
28.4/-2
39.8239
77/25
10
125.6/52
3.1918
30.2/-1
37.1988
78.8/26
9.5507
127.4/53
3.0707
32/0
35.2024
80.6/27
9.1245
129.2/54
2.959
33.8/1
33.3269
82.4/28
8.7198
131/55
2.8442
35.6/2
31.5635
84.2/29
8.3357
132.8/56
2.7382
37.4/3
29.9058
86/30
7.9708
134.6/57
2.6368
39.2/4
28.3459
87.8/31
7.6241
136.4/58
2.5397
41/5
26.8778
89.6/32
7.2946
138.2/59
2.4468
42.8/6
25.4954
91.4/33
6.9814
140/60
2.3577
44.6/7
24.1932
93.2/34
6.6835
141.8/61
2.2725
46.4/8
22.5662
95/35
6.4002
143.6/62
2.1907
48.2/9
21.8094
96.8/36
6.1306
145.4/63
2.1124
50/10
20.7184
98.6/37
5.8736
147.2/64
2.0373
51.8/11
19.6891
100.4/38
5.6296
149/65
1.9653
53.6/12
18.7177
102.2/39
5.3969
150.8/66
1.8963
55.4/13
17.8005
104/40
5.1752
152.6/67
1.83
57.2/14
16.9341
105.8/41
4.9639
154.4/68
1.7665
59/15
16.1156
107.6/42
4.7625
156.2/69
1.7055
60.8/16
15.3418
109.4/43
4.5705
-
-

3. 3 Operation Modes and Functions
3.3.1 Auto mode function requirement
TS range is 62 ~88 17 ~30
When T1<TS-1, select the setting temperature of
TS-1 for Heating operation’s temperature.
When TS+2≥T1≥TS-1,select the Fan-only mode.
When T1>TS+2, select the setting temperature(TS )
for Cooling operation’s temperature.
The indoor fan motor operates at Auto-fan mode with
speed uncontrolled and not changed.
3.3.2 Fan-only mode function requirement
The compressor and outdoor fan are OFF at Fan-
only mode (except P1 protection).
The speed of indoor fan can be optionally chosen as High/Mid/Low.
The TS can’t be controlled because of the LED displaying as T1.
The ION/TIMER functions are valid at the fan-only mode.
3.3.3 Cooling mode function requirement
The speed of indoor fan can be optionally selected as High/Mid/Low.
The outdoor fan will be turned on as soon as the unit being on
cooling mode.The operation of outdoor fan is according to the
compare of T1 and TS when the water level is below to switch 1.
If not, the outdoor fan doesn’t work.
The compressor operates as below:
Operation conditon
(T1-Ts)℃Compressor on
+1
0
Compressor off
a) If T1 TS+1 , outdoor fan
operates. After 15 seconds,
compressor operates.
b) The compressor is on, if
T1≤TS, this compressor will
stop. If outdoor fan operates for
3 minutes at least, it will stop
for a delay for 5 seconds.

When the unit is off, the compressor stops at first, and the
indoor/outdoor fan will stop for a delay of 5seconds. (If it operates at
heating mode, the outdoor fan will be off for a delay of 30 seconds).
The ION/TIMER functions are valid at the cooling mode.
3.3.4 Drying mode function requirement
At Drying mode, TS can’t be controlled by display
panel, and LED display as T1.
The unit operates at drying mode. If T1>55.4 13 , outdoor fan turns
on, and then the compressor operates after 15 seconds later.
Operation conditon
T1
℃
Compressor on
15
13
Compressor off
a) When T1<55.4 13 ,
compressor stops working.
And outdoor fan will stop
for a delay of 5 seconds.
b) When T1≥59 15 , outdoor
fan operates, and
compressor will restart
operation after 15seconds.
The speed can’t be controlled at drying mode, and indoor fan motor
operates at low speed.
The ION/TIMER functions are valid at the drying mode.
3.3.5 Heating mode function requirement(for Electronic Heater)
TS range is 62 ~88 17 ~30
The speed of indoor fan can be optionally chosen as Auto/High/Mid/Low.
At heating mode, the heater will operate according to the difference between
T1 and TS. Electronic heater operates as below:
Operation conditon
(T1-Ts)℃
Heater off
+1
0
Heater on
a) When T1 TS, indoor fan
operates firstly, then heater
operates after 4 seconds.
b) If T1 TS 1 , turn off heater.
Then turn off indoor fan motor
for a delay of 10 seconds..