Comcater ANC9 G Series Guide

GAS HOBS AND RANGES/GAS SOLID TOP RANGES
Mod. ANC9..G
Mod. ANC9F...G
Mod. ANT9....G
INSTRUCTIONS FOR INSTALLATION, ADJUSTMENT, USE AND MAINTENANCE .....................................................page 2-6
APPENDIX........................................ .... .... .... .... .... .... .... . .. . .... .... .... ....................pagina 7- 9
Read the manual thoroughly
and keep it in a safe place
throughout the product's
service life.
Read the warning notes
immediately!
DOC. NO. CR0687760
0805

INSTALLATION DIAGRAM
SERIE 90 - GAS HOBS AND RANGES
Mod. ANC9..G
Measurements in cm
Key
G - Gas connection ISO 7/1 R3/4
(CR0687760) 1

INSTALLATION DIAGRAM
SERIE 90
Mod. ANC9FG..G
INSTALLATION DIAGRAM
Measurements in cm
Key
G- Gas connection ISO 7/1 R3/4
(CR0687760) 2

INSTALLATION DIAGRAM
SERIE 90 - GAS SOLID TOP RANGE
Mod. ANT9….G
Measurements in cm
Key
G - Gas connection ISO 7/1 R3/4
(CR0687760) 3

1 JOINING APPLIANCES TOGHETHER IN LINE
4

FIG. 2 MAIN BURNER / PILOT BURNER
FIG. 3 GAS VALVE / TAP
5

TECHNICAL DATA
NATURAL
GAS PROPANE
MAIN 2.10 1.30
PILOT 41 20
TURNDOWN SCREW
0.90
1/4 Turn
open
From fully in
0.65
Fully in
MAIN 2.85 1.65
PILOT 41 20
TURNDOWN SCREW 1.30
Fully in
0.90
Fully in
MAIN 2.55 1.50
PILOT 41 25
TURNDOWN SCREW
1
Turn open
From fully in
1
Turn open
From fully in
NATURAL
GAS PROPANE
Ø 65 OPEN BURNER --
Ø 100 OPEN BURNER --
OVEN BURNE
R
21
NATURAL
GAS PROPANE
Ø 65 OPEN BURNER 21.6 21.6
Ø 100 OPEN BURNER 37.5 35.5
OVEN BURNER 31.5 28.8
ANC94G20 (TOTAL) 75.00 71.00
ANC98G40 (TOTAL) 150.00 142.00
ANC912G44 (TOTAL) 161.4 157.4
ANC9FG8G36 (TOTAL) 133.8 129.1
ANC9FG8G48 (TOTAL) 181.5 170.8
ANC9FG12G52 (TOTAL) 192.9 186.2
ANC9FG16G72 (TOTAL) 267.6 258.2
ANC9FE8G28 (TOTAL) 102.3 100.3
ANC9FE12G44 (TOTAL) 161.4 157.4
NATURAL
GAS PROPANE
NATURAL GA
S
PROPANE
kPa 1.00 2.50
Model NATURAL GA
S
PROPANE
ANC94G20 set pressure whit 1 x OB100 open
burner at maximum
set pressure whit 1 x
OB100 open burner at
maximum
ANC98G40 set pressure whit 2 x OB100 open
burner at maximum
set pressure whit 2 x
OB100 open burner at
maximum
ANC912G44
set pressure whit 2 x OB65 open burber
at maximum + 1 x OB100 open burner
at maximum
set pressure whit 2 x
OB65 open burber at
maximum + 1 x OB100
open burner at
maximum
ANC9FE8G28
set pressure whit 1 x OB65 open burber
at maximum + 1 x OB100 open burner
at maximum
set pressure whit 1 x
OB65 open burber at
maximum + 1 x OB100
open burner at
maximum
ANC9FE12G44
set pressure whit 2 x OB65 open burber
at maximum + 1 x OB100 open burner
at maximum
set pressure whit 2 x
OB65 open burber at
maximum + 1 x OB100
open burner at
maximum
ANC9FG8G36 set pressure whit OB100 open burner +
OVEN burner operating at maximum
set pressure whit 2 x
OB65 open burners
operating at maximum
ANC9FG8G48
set pressure whit 1 x OB100 open
burner + OVEN burner operating at
maximum
set pressure whit 1 x
OB100 open burner +
OVEN burner operating
at maximum
ANC9FG12G52
set pressure whit 1 x OB65 open burber
at maximum + 1 x OB100 open burner
at maximum + OVEN burner operating
at maximum
set pressure whit 1 x
OB65 open burber at
maximum + 1 x OB100
open burner at
maximum + OVEN
burner operating at
maximum
ANC9FG16G72
set pressure whit 2 x OB65 open burber
at maximum + 1 x OB100 open burner
at maximum + OVEN burner operating
at maximum
set pressure whit 2 x
OB65 open burber at
maximum + 1 x OB100
open burner at
maximum + OVEN
burner operating at
maximum
POWER - KW A CABLE
ANC9FE..G 6 13 5 G 1,5
(CR0687760) 6
Ø 65 OPEN BURNER
OVEN BURNER
MM
MARKING
MARKING
MM
T6 - POWER / POWER SUPPLY
T3 - NOMINAL GAS CONSUMPTION
415 3N~ 50/60 Hz
T5 - NOMINAL TEST POINT PRESSURE VALUES
Values shown are those measured at the manifold pressure test point
GAS HOBS AND RANGES
T4 - MAXIMUM GAS INLET PRESSURE
Ø 100 OPEN BURNER
1.13 2.75
T1 - INJIECTOR OREFICES SIZES
T2 - AERATION SHUTTERS SETTING
Vac / f
MM
MM
MARKING
MJ/h
MM
kPa
MM
AMM

TECHNICAL DAT
A
NATURAL
GAS PROPANE
MAIN 3.00 1.80
PILOT 27 14
TURNDOWN SCREW 1.80
Fully in
1.35
Fully in
MAIN 2.55 1.50
PILOT 41 25
TURNDOWN SCREW --
NATURAL
GAS PROPANE
SOLID TOP BURNER 40 35
OVEN BURNER 21
NATURAL
GAS PROPANE
SOLID TOP BURNER 44.00 40.5
OVEN BURNER 31.5 28.8
ANT98G (TOTAL) 44.00 40.5
ANT9FG12G (TOTAL) 134.6 126.4
ANT9FG8G (TOTAL) 75.5 69.3
NATURAL
GAS PROPANE
NATURAL
GAS PROPANE
SOLID TOP BURNER
VALUES SHOWN ARE THOSE
MEASURED AT THE MANIFOLD
PRESSURE TEST POINT.
1.00 2.50
OVEN BURNER
VALUES SHOWN ARE THOSE
MEASURED AT THE MANIFOLD / OR
GAS VALVE PRESSURE TEST POINT.
1.00 2.50
GAS SOLID TOP RANGES
2.75
MM
MJ/h
kPa
MM
T1 - INJIECTOR OREFICES SIZES
T2 - AERATION SHUTTERS SETTING
kPa
1.13
T3 - NOMINAL GAS CONSUMPTION
T4 - MAXIMUM GAS INLET PRESSURE
(CR0687760) 7
SOLID TOP BURNER
OVEN BURNER
MMA
MM
MARKING
MM
T5 - NOMINAL TEST POINT PRESSURE VALUES
MARKING

ATTENTION
The data plate is inside the control panel.
CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page
INSTALLATION INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . .7
Positioning
Joining appliances togheter in line
Connecting to the gas supply
Connecting to the electrical power supply
Earth and equipotential connection
CONVERSION TO DIFFERENT TYPE OF GAS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Replacement of burner injector and pilot burner injector of cooking hob (Fig. 2A / 2B )
Replacement of burner injector and adjustment of burner air flow of solid top (Fig. 2E)
Replacement of pilot burner injector of solid top(Fig. 2F)
Adjustment of minimum flow to the cooking hob burners and solid top burner (Fig. 3A)
Replacement of burner injector and adjustment of burner air flow of oven (Fig. 2C)
Replacement of pilot burner injector of oven (Fig. 2D)
Adjustment of the gas control outlet pressure
COMMISSIONING PROCEDURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Testing the gas system
Testing the gas nominal thermal power
Setting the manifold gas pressure
Testing the electric oven
Ckecking the electric nominal thermal power
TROUBLESHOOTING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
The pilot burner is difficult or impossible to ignite
The pilot burner goes out during use
The main burner is difficult or impossible to ignite
The temperature of gas oven is difficult or impossible to regulate
Electric oven elements do not heat
The temperature of electric oven is difficult or impossible to regulate
REPLACEMENT OF SPARE PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Burners, Thermocouples, Gas taps of cooking hob and solid top
Gas valve, Piezo igniter of gas oven
Burners, Thermocouple, Ignition electrode of gas oven
Electric oven heating elements
Electric oven working and safety thermostat
USE AND MAINTENANCE INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
WARNINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Safety device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. .9
Use of cooking hob
Turning on the cooking hob burners
Turning off the cooking hob burners
Use of gas oven
Turning on the oven burners
Turning off the oven burners
Use of electric oven
Turning on the oven
Turning off the oven
CARE AND MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
SPARE PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
(CR0687760) 8

(CR0687760) 9
INSTALLATION INSTRUCTIONS
CONFORMITY TO REGULATIONS AND LAWS
The appliance is to be installed by an authorised person in
accordance with AS5601 - the installer must ensure the
installation complies with all regulatory and manufacturer
requirements and operationally and functionally test, make
necessary adjustments and commission the appliance as part
of installation. WARNING
The manufacture declines any responsibility if these
obligations are not respected.
INSTALLATION
The overall dimensions, position/dimensions of connections
and technical data are given in the installation diagram.
If the appliance cannot be adjusted to perform correctly call
the tecnichal assistant service.
Positioning
• Install the appliance in a suitably ventilated environment.
• Position the appliance at least 15 cm from surrounding
walls. This distance may be reduced if the walls are
flameproof or protected by insulating material.
• This appliance is not designed for built-in installation.
• Remove the protective film from the external panels.
Use a suitable solvent to remove any glue residue.
• In stand-alone installations, appliances 40 or 60 cm wide
must be fixed to the floor using the flanged feet.
• Level the appliance by means of the adjustable feet.
• In case of installation on a level bench top, it must be used
the approriate feets equipped with the applince (height = 30
mm).
Joining appliances together in line ( Fig. 1 )
• Remove the control panels ( Fig. 1A ).
• Remove the fixing screw nearest the control panels, from
each side to be joined ( Fig. 1B ).
• Place the appliances next to each other and level them until
the tops match ( Fig. 1C ).
• Insert the coupling plate ( supplied ) into the side housings
on the backs. Join together the appliances screwing M5
flathead screws ( supplied ) in to coupling plate ( Fig. 1D ).
• Turn 180º one of the two plates inside the appliances to be
joined together ( Fig. 1E ).
• Join together the appliances , at the front side, screwing the
M5x40 screw ( supplied ) on the opposite insert (Fig. 1F ).
Connecting to the gas supply
• Install a shut-off valve upstream of the appliance, in a
place easily accessible.
• Check if the appliance is adjusted for the type of gas with
which it will be supplied. If not, convert it according to the
instructions in the paragraph "Conversion to different type of
gas".
• Do not use supply pipe having a diameter smaller than the
appliance’s gas connection.
• Check that there are no leaks at the connection points.
Connecting to the electrical power supply
• The appliance is set to operate at the voltage indicated on
the data plate.Total power is given in table T6 in Technical
Data section.
• The appliance must be supplied with a separate electrical
line using a flexible rubber cable with insulating properties
not inferior to H07RN-F. The length of the cable between the
cable clamp and the connection terminal blocks must be such
that the live conductors tighten before the yellow/green earth
wire, in case the cable come out of the cable clamp.
• Install suitable automatic cut-off switches (contact opening
of at least 3 mm) and highly sensitive automatic differential
protection devices. These must guarantee protection against
direct or indirect contact with live parts and against currents
towards earth in the event of malfunction (maximum
dispersion current 1 mA/kW).
• To access terminal board remove the front panel.
• Connect the power supply cable to the terminal board as
shown in the wiring diagram supplied whit the appliance.
Earth and equipotential connection
• The appliance must be earth connected on the terminal
block marked by the symbol located beside the input line
terminal block.
• The metal structure of all the appliances installed must be
connected together on the terminal marked by the symbol
located close to the earth terminal (equipotential system).
CONVERSION TO A DIFFERENT TYPE OF GAS
To convert the appliance to a different gas supply, follow the
instructions below.
Use the injectors contained in the bag supplied with the
appliance.
Replacement of burner injector and pilot burner injector
of cooking hob (Fig. 2A / 2B )
• Remove pan grids, burner units, front panel.
• Unscrew the existing injectors "U" / “UP” and replace them
with the ones indicated in Table T1 in Technical Data
section.
Replacement of burner injector and adjustment of
burner air flow of solid top (Fig. 2E)
• Remove front panel.
• Unscrew the existing injector "U" and replace it with the
one indicated in Table T1 in Technical Data section.
• Position the air regulator at the distance “A” indicated in
Table T2 in Technical Data section.
• Retighten screw V and seal it with red paint.
Replacement of pilot burner injector of solid top(Fig. 2F)
• Remove plate , front panel.
• Unscrew fitting R and replace injector “UP” with the one
indicated in Table T1 in Technical Data section.
• Retighten fitting R.
Adjustment of minimum flow to the cooking hob burners
and solid top burner (Fig. 3A)
• Remove the front panel.
• Unscrew the existing screw "VM" and replace it with the
one indicated in Table T1 in Technical Data section.
Replacement of burner injector and adjustment of
burner air flow of oven (Fig. 2C)
• Remove the panel under oven's door.
• Unscrew screw “V”.
• Unscrew the existing injector "U" and replace with the one
indicated in Table T1 in Technical Data section.
• Position the air regulator at the distance “A” indicated in
Table T2 in Technical Data section.
• Retighten screw V and seal it with red paint.
Replacement of pilot burner injector of oven (Fig. 2D)
• Remove the panel under the oven's door.

(CR0687760) 10
• Unscrew fitting R and replace injector “UP” with the one
indicated in Table T1 in Technical Data section.
• Retighten fitting R.
Adjustment of the gas control outlet pressure
• The outlet pressure adjustment screw is factory
commissioned (fully in) and sealed with red paint.
No adjustment are required in case of conversion to a
different type of gas.
COMMISSIONING PROCEDURE
Testing the gas system
• Switch on the appliance following the instructions for use.
Test burners ignition and flame uniformity. Also check the
appliance for gas leaks and make sure the gas exhaust system
functions correctly.
• If necessary, consult the “Troubleshooting guide” below.
Testing the gas nominal thermal power
• After installation, conversion to a different type of gas or
servicing, check the nominal thermal power of the appliance.
• The appliance functions at the nominal thermal power when
is fitted with the appropriate injectors for the gas used, the
gas control is commissioned according to manufacturer
requirements (see paragraph "Adjustment of the gas control
outlet pressure), and the gas pressure measured at the
manifold pressure test point is commissioned to the
appropriate nominal value as specified in Table T5 in
Technical Data section.
Setting the manifold gas pressure (Fig. 3)
• Remove the front panel.
• Remove sealed bolt PP from the test point pressure and
connect the pressure gauge pipe.
• Switch on the appliance following the instructions for use
and commission the test point pressure values to the
appropriate nominal values as specified in Table T5 in
Technical Data section.
Testing the electric oven
• Switch on the oven following the instructions for use.
• Check the correct functioning of the controls and heating
elements, trying the various combinations (bottom heating,
top heating and simultaneous top and bottom heating).
• If necessary, consult the “Troubleshooting guide” below.
Cheking the electrical nominal thermal power
• After installation, check the nominal thermal power of the
appliance.
• The appliance functions at the nominal thermal power when
the electrical power supply is as indicated in Table T1 in
Technical Data section.
TROUBLESHOOTING GUIDE
The pilot burner is difficult or impossible to ignite
• Gas supply pressure low.
• Gas pipe or injector clogged.
• Gas tap/valve faulty.
• Piezo igniter faulty.
• Ignition electrode (ignition spark gas should be 3 + 1/0 mm)
or cable faulty.
The pilot burner goes out during use
• Thermocouple faulty, insufficiently heated or incorrectly
connected to gas valve.
• Gas tap/valve faulty.
The main burner is difficult or impossible to ignite
• Gas supply pressure low.
• Injectors clogged.
• Gas tap/valve faulty.
The temperature of gas oven is difficult or impossible to
regulate
• Gas valve faulty.
Electric oven do not heat
• Check the fuses.
• Working thermostat faulty.
• Selector faulty.
• One or more heating elements faulty.
• Safety thermostat in operation or faulty.
The temperature of electric oven is difficult or
impossible to regulate
• Working thermostat faulty.
• One or more heating elements faulty.
REPLACEMENT OF SPARE PARTS
Before every any intervention close the gas and water
shut-off valves upstream the appliance and disconnect the
electrical supply.
Never tamper with any of the sealed components.
After every intervention, check for gas leaks, if necessary.
Burners, Thermocouples, Gas taps of cooking hob and
solid top
• Remove the front panel, pan grids/plate and replace the
component.
Gas valve, Piezo igniter of gas oven
• Remove the front panel and replace the component.
Burners, Thermocouple,Ignition electrode of gas oven
• Remove the front panel, the panel under oven's door and
replace the component.
Electric oven heating elements
• Work from inside the oven. Disconnect the heating
elements from the oven and the cable, and replace them.
Electric oven working and safety thermostat
• Remove the control panel.
• Remove the thermostat bulb from the holder located inside
the oven.
• Disconnect the electrical connections.
• Replace the component.
USE AND MAINTENANCE INSTRUCTIONS
WARNINGS
Do not store flammable materials in or near the appliance. Do
not spray aerosols in the vicinity of this appliance while it is
in operation.
Beware of the appliance’s hot surfaces!
This appliance is designed for professional use and must only
be used by trained personnel. It is exclusively designed to
cook food. Any other use is considered improper.
ATTENTION The use of the steak griddle on the pan grids
is not permitted.
Never leave the oven door open (even partially) during use.
If the appliance breaks down, close the gas shut-off valve
upstream of the appliance and call the technical assistance
service.

(CR0687760) 11
Repairs should only be carried out by authorised service
centres.
For service and spares parts, please contact Comcater 1800
810 161.
The manufacture declines any responsibility if these
obligations are not respected.
Read this manual carefully and keep in a safe place.
Before using the appliance, thoroughly clean all surfaces that
may come into contact with food.
Safety device for electric oven
• A manually-reset safety thermostat, automatically cuts off
the electrical supply to the heating elements when the
temperature in the oven exceeds the maximum working
temperature permitted (working thermostat faulty). To restore
operation, remove the front panel and press the thermostat
reset button. If the oven does not heat, disconnect the
electrical power supply to the appliance and call the technical
assistance service.
USE
Use of cooking hob and solid top
The gas tap control knob has the following positions:
• off
pilot ignition
maximum flame
minimun flame
Turning on the cooking hob / solid top burners
• Press the knob in and turn to the position “ Pilot ignition”.
• Press the knob fully and light the pilot manually. Hold the
knob pressed in for approx. 20 seconds, then release it. If the
pilot flame goes out, repeat the operation
Make sure the pilot burner is lit by checking the flame
through the inspection hole on burner body (cooking hob ) or
on front panel ( solid top ).
• To light the main burner, turn the knob from “pilot on” to
“maximum flame”.
• For the minimum flame, turn the knob from “maximum
flame” to “minimum flame”.
Turning off the cooking hob burners
• To switch off the main burner, turn knob to position “ Pilot
ignition”.
• To switch off the pilot burner, press and turn knob to
position “Off”.
Use of gas oven
The gas valve control knob has the following positions:
●Off
Pilot ignition
100° C Minimum cooking temperature
300° C Maximum cooking temperature
Turning on the oven burners
• Press the knob in and turn to position “ Pilot ignition”.
• Press the knob fully and press the piezo igniter button to
light the pilot flame. Hold the knob pressed in for approx. 20
seconds, then release it. If the pilot flame goes out, repeat the
operation.
The pilot can be seen and if necessary lit throught the hole in
the floor of the oven.
• Turn the knob to the desired cooking temperature.
Turning off the oven burners
• To switch off the main burner, turn knob to position “ Pilot
ignition”.
• To switch off the pilot burner, turn knob to position “Off”.
Use of electric oven
The oven is equipped with two control knobs and one yellow
pilot light.
The selector knob is marked with the following symbols:
0 Not in operation
Top heating (grill) in operation
Bottom heating in operation
Top + bottom heating in operation
The working thermostat knob is marked with the following
symbols:
• Off
50 Minimum cooking temperature
100-200 Intermediate cooking temperature
300 Maximum cooking temperature
Turning on the oven
• Turn the selector knob to the desired cooking position.
• Turn the working thermostat knob to the desired cooking
temperature (yellow indicator lights).
Turning off the oven
• Turn the working thermostat knob to position “Off”.
• Turn the selector knob to position "0".
CARE AND MAINTENANCE
• Do not wash the appliance with jets of water.
• Before cleaning the appliance, disconnect from the electric
power supply (if connected).
• Clean stainless steel surfaces daily using water and non-
abrasive detergents. Rinse thoroughly and dry.
• Do not use steel wool pads or chlorine-based products.
• Do not use corrosive substances to clean the floor
underneath the appliance.
• If the appliance is to remain idle for a long period, close the
gas shut-off valve upstream of the appliance and clean
thoroughly.
• The appliance should be inspected and the gas exhaust pipe
cleaned by an authorised service engineer at least twice a
year.
For this purpose we recommend taking out a service contract.
Cleaning the interior of the oven
Daily cleaning of the interior of the oven avoids maintenance
problems in the future.
Use a suitable degreasing spray product (not foaming) for
cleaning even in the “hidden” zones.
• heat the oven to 75 – 80° C.
• spray the degreasing solution throughout the interior of the
oven, on the grilles, the grille supports and the oven floor.
• close the oven door and allow the product to react for about
20-30 minutes.
• open the oven door carefully, paying attention to the eyes
and the skin.
• remove from the oven cavity the grille supports, the grilles
and the floor and wash separately.
• clean and rinse the oven interior with a sponge using tepid
soapy water and/or normal liquid detergents, drying
afterwards.
• Remount the internal parts and dry further by turning on the
heating for a few minutes.

(CR0687760) 12
SPARE PARTS LIST
Gas Ranges
• Gas tap
• Gas valve
• Cooking hobburners
• Solid top burner
• Oven burner
• Pilot burner
• Thermocouple of cooking hob , solid top and oven
• Ignition electrode
• Piezo igniter
Electric oven
• Working thermostat
• Selector
• Heating element
• Yellow pilot lamp
• Safety thermostat