Comfortaire Comfort-Cure RG-61A User manual

0010562911
TEMPERATURE
1
2
3
4
10
9
8
7
65
FAN ONLY
MIN
COOL
MAX
COOL
SPEED
LOWHI
OFFON
Wa t 3 M nutes Before
Restart ng
POWER
RG-61A

1
1
2
4
4
5
5
6-7
8-13
8
8-13
14-18
15
15
16-18
19-20
20-21

Test power plug before each use:
1. Press reset button.
2 . Press test button, unit should trip.
. Press reset button again for use .
Do not use if above test fail.
In the event this device trips , the cause of the malfunction is to
be corrected before further use of the device .
Important:

5
5

2-way
airflow
control paneleasy access filters
MODEL: RG-61A
TEMPERATURE
1
2
3
4
10
9
8
7
65
FAN ONLY
MIN
COOL
MAX
COOL
SPEED
LOWHI
OFFON
Wa t 3 M nutes Before
Restart ng
POWER
2. MODE S t Switch
5. How Th Unit Drains

Fig. # 1
TEMPERATURE
1
2
3
4
10
9
8
7
65
FAN ONLY
MIN
COOL
MAX
COOL
SPEED
LOWHI
OFFON
POWER

Also wh n you shut off th air condition r wait for 3 minut s
b for turning it on again.
POWER Turns air conditioner off.
SPEED "LOW" Low speed fan operation with cooling or not.
SPEED "HI" High speed fan operation with cooling or not.
This automatically controls the temperature of indoor air. Turn the knob
so that arrow points to the cooler marks for more moderate cooling.
Normal Fan
1. Turn the SPEED mode switch to the "HI" or the "LOW" setting.
2. Set the thermostat control to the temperature mark "FAN ONLY".
Normal cooling
1. Turn the SPEED mode switch to the "HI" or the "LOW" setting.
2. Set the thermostat control to the desire temperature (the mid-point
is a good starting position).
If the room temperature is not satisfactory after a reasonable time, adjust
the control to a warmer or cooler setting, as appropriate.
Maximum cooling
1. Turn the SPEED mode switch to the "HI" setting
2. Set the thermostat control to the MAX COOL temperature mark.
Qui t r op ration
1. Turn the SPEED mode switch to the "LOW" setting.
2. Set the thermostat control as needed.
CAUTION:
1
2

10
window seal gasket
short screws 1 / 2"
wood screws 1/ 2"
Model:RG-61A
top rail

11
Insert the side curtains into the
top and bottom rails of the air
conditioner. Fasten the curtains
to the unit with 8 short screws
1 / 2".
Install top rail with short
screws1 / 2".
ASSEMBLE
CURTAINS/TOP RAIL
TEMPERATURE
1
2
3
4
10
9
8
7
65
FAN ONLY
MIN
COOL
MAX
COOL
SPEED
LOWHI
OFFON
Wat 3 M nutes Before
Restartng
POWER
RG-61A
12
5
1
8
6
22
12 7
16
18 9
16
1411
16
5
25
1
2

12
1. This unit is designed for installation in standard double hung windows
with actual opening widths of 22 to 6 . The upper and lower sash
must open sufficiently to allow a clear vertical opening of 14 from the
bottom of the sash to the window sill.
2. If storm window presents interference, fasten a 2 wide wood strip(not
included) (OUTER SILL) to the inner window sill across the full width of
the sill. The wood strip should be thick enough to raise the height of
the window sill so that the unit can be installed without interference by
the storm window frame (STORM WINDOW FRAME) or wood strip
(OUTDOORS) to help condensation to drain properly to the outside.
. Install a second wood strip (approximately 6 long by 1-1/2 wide
and same thickness as first strip) in the center of the outer sill flush
against the back off the inner sill. This will raise basepan angle .
4. If the distance between STORM WINDOW FRAME and WOOD STRIP
MOUNTED ON TOP OF INNER SILL is more than 1 , two of wood
strip are not necessary.
INNER
SILL
OUTER
SILL
I
N
D
O
O
R
S
O
U
T
D
O
O
R
S
WOOD STRIP
MOUNTED ON
TOP OF INNER SILL
WOOD STRIP
FOR BASEPAN
ANGLE
STORM
WINDOW FRAME
1 MAX.
/4 CLEARANCE
I
N
D
O
O
R
S
O
U
T
D
O
O
R
S
INNER
SILL
OUTER
SILL
LOCATING UNIT IN
WINDOW
Open the window and mark center line on the
center of the inner sill.
CENTER LINE
INNER SILL
INDOOR SIDE
ATTACH BASEPAN
ANGLE
CENTER LINE
SHORT SCREW1 / 2"
INNER SILL
OUTER SILL
SHORT SIDE
BASEPAN ANGLE
8
8
OUTSIDE
INSIDE
Install the basepan angle behind the inner window sill, with
the short side of basepan angle as shown. Use the 2 short
screws1 / 2" provided.
The basepan angle helps to hold unit securely in place.
Be sure to place basepan angle edge flush against back
of inner sill.
2

13
INSTALL THE AIR CONDITIONER
IN THE WINDOW
Carefully lift the air conditioner and slide it into the open
window. Make sure the bottom guide of the air conditioner
drops into the notches of the basepan angle.
While steadying the air conditioner ,carefully bring the
window sash down behind the upper guide of the air
conditioner.
WINDOW FRAME
UPPER GUIDE
BOTTOM GUIDEBASEPAN ANGLE
ABOUT 1/4
INSTALL THE SEAL GASKET
AND SASH LOCK
Extend the side curtains to fill the
window opening using 4 wood screws
1/ 2" to secure them.
Cut the seal gasket to the window
width. Stuff the sash seal between the
glass and the window to prevent air
and insects from getting into the room.
Fasten the basepan angle, using a
short screw1 / 2".
BASEPAN ANGLE WINDOW SEAL GASKET
SHORT SCREW1 / 2"
WOOD SCREW 1/ 2"

Th air filt r b hind th front grill should b ch ck d and
cl an d at l ast onc v ry 2 w ks or mor oft n if n c ssary.
To remove:
1. Open the inlet grille downward by pulling out the top of the inlet grille.
2. Remove the air filter from the front grille assembly by pulling the air filter
up slightly.
. Clean the filter with warm, soapy water below 40oC(104oF).
4. Rinse and gently shake the water from the filter and let it dry before replacing
it.
Always us a soft cloth damp n d with wat r or mild soap
and wat r solution to wip th front of th cabin t.
To cl an th front pan ls or th cabin t DO NOT us harsh
ch micals, abrasiv s, ammonia, chlorin , bl ach, conc ntrat d
d t rg nts, solv nts or m tal scouring pads.
DO NOT us your air condition r without th air filt r in plac .
Always unplug your air condition r b for cl aning.
TEMPERATURE
PEED
LOW
OFF
POWER
1
2
3
4
10
9
8
7
65
FAN ONLY
MIN
COOL
MAX
COOL

(see page 8)
(see page 18)