Commercial Pro PSCP-100 Owner's manual

Thank you for purchasing the “COMMERICAL PRO” basketball game. We hope you enjoy the
quality, durability and amusement that has made our products the leading producer of pool related
accessories and activity products for two decades.
PRODUCT/SERVICE/INSTRUCTION
INFORMATION
Phone: [phone]
Fax: [phone]
P.O. Box 607
4920 State Road
Ashtabula, Ohio 44005-0607
Shaping Ideas In Plastic

POOLSIDE BASKETBALL GAME
(MODEL #PSCP-100)
CARTON’S CONTAIN THE FOLLOWING: MATERIALSNEEDED:
(1) WATER/SAND FILLABLE BASE - WATER OR SAND
(1)MATINGBLOCK
(1) BACKBOARD
(1) RIM
(1) NET
(2) BASKETBALLS TOOLS NEEDED:
(1) POLY BAG SUB-ASSEMBLY (WHICH INCLUDES): - (2) 1/2” SOCKETS
(1) POLY BAG - SOCKET EXTENION (OPT)
(3) .312 DIAMETER x 4.375” LG HEX HD PLATED BOLT - SOCKET RATCHET OR
(1) .312 DIAMETER x 3.250” LG HEX HD PLATED BOLT - BOX END WRENCH OR
(12) .312 DIAMETER WASHER - DRIVE SOCKET
(1) ORANGE PLUG
(4) .312 DIAMETER x 3.00” LONG HEX HD PLATED BOLT
(4) .312 DIAMETER HEX NUT
(1) PRODUCT/SERVICE INFORMATION SHEET
BEFORE STARTING WE RECOMMEND THAT ASSEMBLY OF THIS UNIT SHOULD BE PERFORMED AT THE LOCATION
OF YOUR SWIMMING POOL WHERE THE UNIT WILL BE USED. BE CAREFUL LIFTING ANY PART OF THE UNIT; THIS
MAY CAUSE INJURY.
Placement of product with A INGROUND SWIMMING POOL should be AT THE THREE TO FIVE FOOT
DEPTH LEVEL. This IS pool shot products RECOMMENDATION FOR UNIT USE.
PRODUCT USEAGE INSTRUCTIONS (PLEASE READ ALL USEAGE INSTRUCTIONS BEFORE STARTING PROJECT):
If using water as weight: Take a garden hose and place hose end into the fill hole located at
the BACK NECK AREA. Now turn on the water and fill the base to ONLY about 1/3 of its full ca-
pacity with water, then shut the water off. This amount of water weight will allow the base
to stand securely enough for the attachment of the BACKBOARD AND RIM. THE BASE will be light
enough for safer, easier movement of the unit up to its final point of use. This will be done
later in the assembly process.
If using sand as weight: Fill the
base with sand through the fill hole
located at the top of base next to
the molded in ball holder. Fill the
base to ONLY about 1/3 of its full ca-
pacity with sand, then stop. This
amount of sand weight will allow
the base to stand securely enough
for the attachment of the BACK-
BOARD AND RIM. THE BASE will be light
enough for safer, easier movement of
the unit up to its final point of use.
This will be done later in the assembly
process.

RIM AND BACKBOARD ASSEMBLY:
Note: before starting assembly project, make sure that the backboard is in the upside down
position for ease of assembly (SEE FIGURE 1).
1) Feed a 5/16” diameter x 3.00” long bolt through the
back hole of the backboard. Make sure you place a
washer on the bolt before inserting through hole (SEE
FIGURE 2).
2) After feeding the bolt & washer combina-
tion through the back hole, hang the rim
on the protruding bolt. (SEE FIGURE 3).
Note: You might need a second set of hands
to hold the rim in place while applying the
fastener. If you do not have a second per-
son to help with this step, prop the rim in
the horizontal position using a box or
other object that will give you the same
result (SEE FIGURE 4).
3) ONCE THE BOLT IS THROUGH THE HOLE IN THE RIM,
PLACE A 5/16” DIAMETER WASHER ON THE PROTRUDING
BOLT AND THREAD A 5/16” DIAMETER NUT ONTO THE
BOLT. DO
NOT
TIGHTEN AT
THIS POINT,
JUST MAKE
SURE THAT
IT IS ON AND
SNUG. (SEE
FIGURE 3).
FIGURE 2
FIGURE 3
FIGURE 1
FIGURE 4 FIGURE 4

RIM AND BACKBOARD ASSEMBLY (CON”T):
4) REPEAT STEPS 1 THROUGH 3 FOR THE OTHER THREE FASTENERS. (SEE FIGURES 5A-5C).
5) AFTER ALL OF THE NUTS ARE SNUG ON THE BOLTS, PROCEED TIGHTENING ALL OF THE NUTS UNTIL THE
BOLT IS ALMOST FLUSH WITH THE TOP OF THE NUT (SEE FIGURE 6).
NOTE: OVERTIGHTENING THE RIM NUTS COULD
CAUSE STRESS ON THE RIM/BACKBOARD ASSEMBLY.
FIGURE 5A FIGURE 5B
FIGURE 5C
FIGURE 6

Fastening the backboard assembly to the base:
6) Slide the mating block into the hole atop the base (see figure 7).
7) AFTER SLIDING THE MATING BLOCK INTO THE BASE
HEAD, MAKE SURE THE BLOCK IS WEDGED TIGHT. .(SEE
FIGURE 8).
NOTE: NOTICE THAT THERE are THREE THREADED IN-
SERTS MOLDED INTO THE FRONT SURFACE OF THE MAT-
ING BLOCK AND ONE THREADED INSERT MOLDED INTO
THE BASE (SEE FIGURE 9).
8) LAY BASE/MATING BLOCK ASSY. ON ITS BACK (SEE FIGURE
10). USING TWO PEOPLE,, ALIGN THE FOUR HOLES ON
THE FRONT OF THE BACKBOARD WITH THE INSERTS IL-
LUSTRATED ABOVE.
9) ONCE YOU HAVE SEATED THE BACKBOARD INTO ITS POCKETS ON
THE BASE, AND THE HOLES ARE NOW ALIGNED WITH THE INSERTS
YOU CAN PROCEED TO THE NEXT STEP. (SEE FIGURE 11).
FIGURE 7
FIGURE 10
FIGURE 8
FIGURE 9A
MOLDED-IN INSERTS (TYPICAL 4 PLACES)
FIGURE 11
POCKETS

Fastening the backboard assembly to the base (CON’T):
10) USE A 4.375” LONG HEX HEAD BOLT TO snugly FASTEN THE TOP THREE LOCATIONS (SEE FIGURE 12A, 12B AND 12C).
11) PROCEED TO THE LOWER HOLE THIS TIME USING A 3.25”
LONG HEX HEAD BOLT (SEE FIGURE 13). Remember to
hand tighten only.
12) Now that all of the bolts are hand tightened, go
back and tighten all four bolts with the necessary
tools. Note: do not over tighten the bolts. This
action could result in permanent damage to the
unit.
FIGURE 12A
FIGURE 9E
FIGURE 12C
FIGURE 13A & 13B
FIGURE 12B
FIGURE 13B

BRINGING THE GAME TO THE POOL FOR FINAL ASSEMBLY:
13) AFTER THE BACKBOARD IS SECURELY TIGHTENED, LIFT
UNIT BACK UP TO PLAYABLE POSITION (SEE FIGURE 14).
FILLING THE BASE FOR STABILITY SAFETY:
14) NOW THAT THE GAME IS ASSEMBLED AND SECURE,
very carefully slide the unit up to the edge of
the swimming pool. Leave approximately 2 - 3
inches between the FRONT EDGE OF THE base and
the pool's edge (SEE FIGURE 15).
MAKE SURE THE BASE DOES NOT OVER-HANG THE
POOL DECK
Before fully filling with water, we recom-
mend that you pour approximately one (1) pint
of liquid bleach or chlorine into the base to
help prevent algAE growth. REPEAT THIS PROCE-
DURE A FEW TIMES DURING THE SWIMMING SEASON.
AS A GUIDE, POOL SHOT HAS MOLDED IN A 50 GALLON
FILL LINE ON THE BACK OF THE BASE FOR YOUR CON-
VENIENCE. WE DO NOT RECOMMEND OVER FILLING
(SEE FIGURE 16). (Not applicable for sand filling)
16) Once the unit is in it’s upright position AND FILLED WITH
WATER OR SAND, push the orange fill/drain plug into
the hole below the “fill here” text, LOCATED ON THE
BACKSIDE OF THE BASE (See figure 17)
17) YOUR GAME BASE IS
EQUIPPED WITH TWO SMALL
RECESSES TO STORE YOUR
BASKETBALL’S WHEN YOU ARE
NOT ENJOYING THE GAME.
THIS WILL HELP PREVENT
LOSS OF THE BALLS DURING
NON ACTIVITY SESSIONS (SEE
FIGURES 18).
FIGURE 14
FIGURE 17
FIGURE 15
2” TO 3”
WATER
LEVEL
SMALL RECESSES FIGURE 18
UP
FIGURE 16

CAUTION
we are VERY CONCERNED ABOUT CUSTOMER SAFETY AND SATISFACTION.
TO INSURE THAT THE SAFETY AND WELL BEING OF THE USERS OF THis
PRODUCT ARE MET; we have CREATED SOME BASIC GUIDELINES THAT WILL
PROMOTE USER SAFETY.
♦ MAKE CERTAIN THAT THE RIM EXTENDS WELL OVER THE EDGE OF THE POOL
♦ BASE MUST ALWAYS BE COMPLETELY SITUATED ON THE POOL'S DECK WITH
NO OVERHANG
♦ DO NOT HANG ON ANY PART OF THIS UNIT
♦ DO NOT PULL UNIT TOWARDS THE POOL
♦ DO NOT DRAG UNIT ALONG THE GROUND OR DECKING
♦ ONLY USE LIGHT-WEIGHT BALLS SUPPLIED WITH UNIT
♦ THIS BASKETBALL GAME is for Swimming Pool Use ONLY
♦ Adult Supervision is Required AT ALL TIMES FOR SAFE PLAY
IMPORTANT!
Every attempt has been made to provide a trouble free product.
If in the event you have missing or defective hardware OR IF YOU JUST RE-
QUIRE REPLACEMENT PARTS, please call our toll-free customer satisfaction
hot line listed below between the hours of 8:00 am and 5:00 pm eastern
standard time, Monday through friday.
[phone]
[phone] FAX

CARE AND MAINTENANCE
Inspect this equipment periodically before use to insure that
unit is in a safe operating condition.
Check for any loose hardware.
Check base for any signs of leakage.
Do not use this equipment if any hardware is loose or missing.
Do not use this equipment if THE UNIT IS ONLY PARTIALLY FILLED.
Do not use this equipment if structural fatigue or possible
equipment failure is evident. Order replacement parts immedi-
ately before allowing anyone to use this equipment to avoid
possible injuries or property damage.
Play must be halted if unit shows any signs of fatigue or failure.
Chlorine and sunlight are the natural enemies of most materi-
als. To prolong the life of your “COMMERCIAL PRO” BASKETBALL
GAME when the components are not in use for long periods of
time and/or in the off season, remove them from the swimming
pool environment, wash down with plain water using A garden
hose and store them out of direct sunlight and moisture.
Never drag components on any type of surface as damage will
occur to the parts.
BE ABSOLUTELY SURE TO COMPLETELY DRAIN WATER FROM BASE BEFORE
STORING, ESPECIALLY IF UNIT IS SUBJECTED TO FREEZING TEMPERATURES
OR DAMAGE CAN RESULT IN THE UNIT.
* SAVE THESE INSTRUCTIONS FOR FUTURE USE *

LIMITED WARRANTY
We warrant that the pool products manufactured and sold will conform to agreed specifications, will be fit for the uses
or applications for which designed and will be free from defects in materials and workmanship. This warranty will re-
main in effect for a period of one (1) year from the date of delivery. The mail in registration slip must be sent immedi-
ately following delivery of product for this warranty to become effective. Send registration slip to P.O. Box 607, Ash-
tabula, OH 44004. At our option, will either repair or replace, excluding freight costs, any nonconforming or defective
products, provided we receive written notice of and an opportunity to inspect the nonconforming or defective products
within (30) days after the discovery of the nonconformity or defect. This warranty does not apply to products which
have been subject to misuse, misapplication, improper repair, assembly or storage, or which have been otherwise
damaged by the fault or negligence of anyone other than the manufacturer or its agents.
THIS WARRANTY IS EXPRESSLY MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, IN-
CLUDING, WITHOUT LIMITATION, WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE. POOL SHOT PRODUCTS, INC. SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL, INCIDENTAL
OR OTHER DAMAGES.
Please fill out and mail within 10 days to:
P.O. Box 607
Ashtabula, OH 44004
First Name: _______________________Last Name: ____________________________________
Street Address: _________________________________________________________________
City: _________________________________State: _______________Zip: _________________
Phone Number: _________________________________________________________________
Date Purchased: _________________________________________________________________
Product Model Number/Description: _________________________________________________
Place of Purchase: _______________________________________________________________
Purchase Price: __________________________________________________________________
We are very interested in your comments. Please tell us what other types of products you
are in need of for your swimming pool environment. Thank you for your valued input.
______________________________________________________________________________
______________________________________________________________________________
Cut Here
Cut Here
REV. 05/05/06
WARRANTY REGISTRATION