Compak CUBE TAMP User manual

INSTRUCTION
MANUAL
AUTOMATIC ELECTRONIC
COFFEE TAMPER

ORIGINAL INSTRUCTIONS | Ref. quality process 002/03 | v 22/12/2020 | K08021H05
2

ORIGINAL INSTRUCTIONS | Ref.quality process 002/03 | v. 22/12/2020 | K08021H05
3
INDEX
AUTOMATIC ELECTRONIC COFFEE TAMPER
CUBE
TAMP
SAFETY 4
DESCRIPTION 6
INSTRUCTIONS 7
IDENTIFICATION 8
TECHNICAL CHARACTERITICS 9
EXTERNAL COMPONENTS 11
INSTALLATION 12
OPERATION 14
TROUBLESHOOTING 18
DECLARATION OF CONFORMITY 19

ORIGINAL INSTRUCTIONS | Ref. quality process 002/03 | v 22/12/2020 | K08021H05
4
1. SAFETY
This device must be used
exclusively for the functions for
which it was designed: tamping
ground coffee
Do not use the device to press
any other types of food such as
nuts, or granulated foods such
as sugar and others.
This device may be used by
children aged 8 years and over,
by people
with reduced physical, sensory or mental
capacities and by people without prior
experience/knowledge, provided they
have received supervision or instructions
on the safe use of the device and
understand the associated risks.
Children should not be allowed
to play with the device
Cleaning and maintenance
of the device should not be
carried out by children without
supervision.
Avoid allowing liquids to come
into contact with internal or
external surfaces while the appliance is
switched on or off, except for those parts
expressly mentioned in the “CLEANING”
section. If, for any reason, this happens,
unplug it immediately from
the mains and dry all surfaces carefully.
READ THE SAFETY AND USE
INSTRUCTIONS CAREFULLY
BEFORE FIRST USING
THE APPLIANCE

ORIGINAL INSTRUCTIONS | Ref.quality process 002/03 | v. 22/12/2020 | K08021H05
5
When maintaining the coffee
tamper, special care should
be taken as it could cut the
maintainer. The use of suitable gloves
when handling it is recommended.
If it is necessary to access the
interior, where the electrical
components are located, go to
the nearest technical service centre.
If any component should break,
or if any intervention is needed,
we recommend contacting the
technical service centres, which will carry
out the repair or replacement, guaranteeing
that safety standards are adhered to.
Only an authorised supplier
may replace the mains cable of
any machine.
NOTE: The manufacturer will not be liable for damages caused either by the
improper use of the device or by not following the stated safety measures
1. SAFETY
USERS SHOULD PAY SPECIAL
ATTENTION TO AND SCRUPULOUSLY
OBEY THE FOLLOWING SAFETY
INSTRUCTIONS
Any other use will be
considered improper
and dangerous
Do not insert any part of the
body between the coffee
tamper and the holder.

ORIGINAL INSTRUCTIONS | Ref. quality process 002/03 | v 22/12/2020 | K08021H05
6
2. DESCRIPTION
The coffee tamper you have purchased
has been designed using the most
innovative technological systems.
The result is a high quality product that
ensures the best results.
Our products are manufactured entirely
by hand, one at a time, following the most
demanding quality requirements.
In its manufacturing process, quality
materials (aluminium, steel, etc.) are
used, which are suitable for contact with
food.

ORIGINAL INSTRUCTIONS | Ref.quality process 002/03 | v. 22/12/2020 | K08021H05
7
3. INSTRUCTIONS
3.1. This manual provides the information
necessary for the correct installation,
handling and maintenance of the
equipment and highlights the
precautions that should be
taken by the operator.
To ensure you get the best out of the
machine, it is essential to carefully follow
the instructions given in this manual.
If there is any kind of problem, contact the
nearest technical service. This manual
should be kept until the machine is
replaced and must always be available to
the operator.
3.2. This manual uses some special terms,
such as:
• Text in bold to highlight the importance
of some terms.
• Numbers in parentheses after a word,
which match the numbering of the
items in the image to the side or in the
image of the external components.
Example: ( ) - Display
Icons:
Information Attention

ORIGINAL INSTRUCTIONS | Ref. quality process 002/03 | v 22/12/2020 | K08021H05
8
The technical characteristics
plate is indelibly marked with the
following information:
NOTE: The manufacturer reserves the right to change components/congurations of any
model, according to the different geographic market demands.
4. IDENTIFICATION

ORIGINAL INSTRUCTIONS | Ref.quality process 002/03 | v. 22/12/2020 | K08021H05
9
5. TECHNICAL CHARACTERISTICS
5.1. SCOPE
The coffee tamper that you have purchased
is intended for shops and communities
ground coffee needs to be tamped and it
should only be used for this purpose.
Any other use is considered
improper and dangerous.
NOTE: The manufacturer will not be held responsible for any damages resulting from
improper use of the equipment, or for not following the safety measures as outlined
below.

ORIGINAL INSTRUCTIONS | Ref. quality process 002/03 | v 22/12/2020 | K08021H05
10
5. TECHNICAL CHARACTERISTICS
5.2. TECHNICAL DATA
110/220/240 V
50/60 Hz
Voltage/Frequency 65 (W)
Weight
Height
Width
Depth
Tamp diameter
6,3
279,7
165
185
53
58
58,3
Kg mm mm

ORIGINAL INSTRUCTIONS | Ref.quality process 002/03 | v. 22/12/2020 | K08021H05
11
6. EXTERNAL COMPONENTS
4CLEAN
Button
9Switch
3Button
( + )
5Sensor
2
Button ( - )
6
Tamper
disk
7
Lower
clamp
Adjustment
wheel 8
1Display
10 Knob

ORIGINAL INSTRUCTIONS | Ref. quality process 002/03 | v 22/12/2020 | K08021H05
12
7. INSTALLATION
7.2. IMPORTANT WARNINGS
The operator must be a responsible
adult. Never a child nor someone without
the ability to accept that responsibility
When handling the machine, the following
precautions should be obeyed:
• Feet must not be bare.
• Hands and feet must be dry.
• Do not get the machine wet.
• Do not expose the machine to
direct sunlight or other atmospheric
agents.
• Never insert any part of the body
between the tamp area and the
support
• When unplugging the grinder,
always pull on the plug and never
the power cable to avoid a possible
short circuit.
7.1. LEGAL WARNINGS
The installer must read this instruction
manual carefully before installing the
machine
The installation of the device must be
carried out by qualied and
authorised personnel, in
compliance with the current
safety and hygiene standards.

ORIGINAL INSTRUCTIONS | Ref.quality process 002/03 | v. 22/12/2020 | K08021H05
13
7. INSTALLATION
7.4. INSTALLATION
Before connecting the machine, check the
following:
• The characteristics on the data plate
match those of the electrical mains
network.
• The electrical connection plug
matches the socket into which it is to
be plugged.
• Ensure that the electrical power of
the facility is adequate for the power
consumed by the appliance.
• The point of connection to the
electrical mains network must
be protected with the appropriate
electrical protection device.
• The equipment must be correctly
connected to a ground connection
according to the current safety
regulations.
Height 280
11.02
mm
in
Width 166
6.53
mm
in
Depth 186
7.32
mm
in
7.3. WHERE TO USE IT
The appliance must be installed on a
solid, flat surface.
The minimum size of the
workplace, to ensure the best
performance of the device, must be at least
the following:

ORIGINAL INSTRUCTIONS | Ref. quality process 002/03 | v 22/12/2020 | K08021H05
14
8. OPERATION
8.1. POWER SWITCH
The power switch ( 9) has 2 positions:
( )
: Equipment on
: Equipment off
8.2. FITTING THE PORTAFILTER
It is essential that the portalter is perfectly
adjusted to achieve a consistent and level
tamping.
Make sure that the diameter of your
portalter matches that of your Cube Tamp’s
coffee tamp.
To adjust the support height:
Make sure the power switch ( 9)is in the
OFF position. Fig.1
Turn the wheel ( 8) clockwise to lower the
support. Fig 2
Counter-clockwise to raise it.Fig 3
Fig. 1
NOTE: The manufacturer reserves
the right to vary the components
of the machine, according to the
requirements of each market, as
well as technological advances.

ORIGINAL INSTRUCTIONS | Ref.quality process 002/03 | v. 22/12/2020 | K08021H05
15
8.2.1 SENSOR DISTANCE
ADJUSTMENT
The current system allows, through a knob
adjustment, ( ) to change the sensor
distanceto work properly with all types of
portalters. Fig 4
In order to move the sensor away, rotate
clockwise, and counterclockwise to bring
it closer.
This adjustment should only be made in
the event that the factory setting is not
adequate for your portalter.
8. OPERATION
Fig. 2
Fig. 3 Fig. 4
10

ORIGINAL INSTRUCTIONS | Ref. quality process 002/03 | v 22/12/2020 | K08021H05
16
8. OPERATION
8.3. USE
The Cube Tamp is factory calibrated to a
force of 20 kg.
If you want to save another default value
to appear upon start up, turn on the
main switch ( ) and press the + button
( ) while the Cube logo appears on the
display during initialization. When the
Cube logo blinks, increase or decrease
the Kg using the - ( ) and + ( )
buttons and conrm the selection with
the clean ( ) button.
1. Turn on the power switch ( 9)
2. Insert the portalter into the support
(7) until it reaches the bottom.
Its presence will be detected
automatically and the coffee tamp
will lower until it exerts the desired
pressure
3. When the message ( ) appears on
screen ( 1) you can remove the
portalter . Fig 5
2
8.4. TAMPING FORCE REGULATION
The tamping force can be adjusted from
10 to 30 kg or from 22 to 66 lbs (this option
must be factory set).
The default force is 20 kg or 44 lbs
To increase the force use the + button ( 3)
and to decrease it use the - button( 2)
8.4.1 CONFIGURATION LBS. AND KG.
To change between KG and LB you need to:
1. Power off the unit.
2. Power on the unit and touch the “Clean”
Icon when the word CUBE appears on the
screen, which happens almost as soon
as the machine turns on. Don’t touch the
screen until CUBE appears.
3. KG LB will then show up on the screen
4. You will touch the “+” or “-“ depending on
whether you want KG or LB
Once the selection has been made,
the Cube will restart with the new
conguration.
In the case of Ibs., the units will increase or
decrease 2 by 2.
KG LB
9
3
2 3
4
Fig. 5

ORIGINAL INSTRUCTIONS | Ref.quality process 002/03 | v. 22/12/2020 | K08021H05
17
8. OPERATION
8.4.2 LOCKED KEYBOARD
To lock the digital display, simply press the
+ ( ) and - ( ) keys simultaneously for
3 seconds until the lock icon appears. Fig 6
To unlock the digital display just repeat the
same steps until the unlock icon appears.
Fig 7
8.5. CLEANING MODE
For a correct tamping consistency,
daily cleaning of the tamping disk is
recommended.
To do this, press the (Clean) button. The
disk will lower to the pressing position and
stay there for 10 sec. During this time you
can clean it with a brush, or cloth if the disc
is wet.
Fig. 6
Fig. 7
Press the (Clean) button again to return
the disk to its idle position.
If you want the disk to remain in the
pressing position to allow more time for
the cleaning, switch off the appliance
using the switch ( 9)
3 2
NOTE: The grinder shouldn’t be used in
environments (SUCH AS INDUSTRIAL
KITCHENS) where cleaning is done with
direct water spray cleaning.

ORIGINAL INSTRUCTIONS | Ref. quality process 002/03 | v 22/12/2020 | K08021H05
18
9. TROUBLESHOOTING
PROBLEM CAUSE SOLUTION
The disk is stuck in the
portalter
The portalter diameter is too small. Follow the instructions for adjusting
the support, turning it clockwise to se-
parate it from the disk. Press the clean
button to force the movement.
The portalter is conical and the amount of
coffee is too low
The disk does not lower
The Cube Tamp is not powered on
Make sure that the appliance is
connected to the mains socket and
that the ON/OFF switch is in the ON
position.
The support is too low and the portalter
has not been detected
Follow the instructions for adjusting
the support, turning it counter-clockwi-
se to bring it closer to the disk.
The tamping has not been
strong enough
The tamping force has been set too low. Select a higher pressing force using
the (+) button
The support is too low and the tamp
cannot exert enough force
Follow the instructions for adjusting
the support, turning it counter-clockwi-
se to bring it closer to the disk
The tamping is too strong The tamping force has been set too high. Select a lower pressing force using the
(-) button
The tamping is not level
The support is too loose.
Follow the instructions for adjusting
the support, turning it counter-clockwi-
se to bring it closer to the disk
The ground coffee is not level before
tamping
Level the ground coffee before
tamping.
The coffee sticks to the
tamping disk The disk is dirty or damp Follow the instructions in the cleaning section 8.5
The display does not turn on The display screen normally takes
5-10 seconds to reset when powered on
Turn off the unit and wait
5-10 seconds before turning on again

ORIGINAL INSTRUCTIONS | Ref.quality process 002/03 | v. 22/12/2020 | K08021H05
19
10. DECLARATION OF CONFORMITY
Compak Coffee Grinders, s.a.
Molí Barri, Parcela B - Pol. Ind. Can Barri - 08415 Bigues i Riells - Barcelona - Spain
Ph. 34 93 703 13 00 - Fax [phone] - www.compak.es
In accordance with European community directives, quality certicates have been applied. All
materials have been adapted and technical reports are available at our ofces.
2014/30/UE on the approximation of the laws of the Member States relating to
electromagnetic compatibility.
06/42/EC amending Directive 95/16/EC on the approximation of the laws of the Member
States relating to machinery
REG. 1935/2004 amending Directive 89/109/EC on the approximation of the laws of the
Member States relating to material and objects destinated to make contact with nutritional
products.
03/108/EC amending Directive 2002/96/EC on waste electrical and electronic equipment
(WEEE).
2014/34/UE on the harmonization of the laws of Member States relating to electrical
equipment designed for use within certain voltage limits.
2012/19/UE of 04/07/2012 on the approximation of the laws of the Member States on waste
electrical and electronic equipment (WEEE).
11/65/EU related to the restriction on the usage of certain dangerous substances with
electrical equipment and electronics.
Environment
Do not throw the applianceaway with the normal household waste; hand it in at an ofcial
recycling collection point. By doing this, you will help to preserve the environment.
The Legal Representative
Jesús Ascaso

Molí Barri, Parcela B
Polígono Industrial Can Barri
08415 Bigues i Riells
Barcelona - Spain
CONTACT
Phone: [phone]
Fax: [phone]
E-mail: [email protected]
Website: www.compak.es

Original Instructions
Ref. quality process 002/03 | v.22/12/2020 | K08021H05