compulocks UCLGSTDB User manual

Assembly Instructions
Cling Stand SKU: UCLGSTDB \ UCLGSTDW
©
Compulocks Brands Inc. All Rights Reserved.j
www.compulocks.com | [e-mail] | [phone] Sheet 1 of 5
Fixed Mounting
Rotation Mounting
PRIOR TO INSTALL OF VHB PAD
CLEAN BOTH MOUTING SURFACES
USING ALCOHOL PADS PROVIDED
ROTATION CLEARANCE FOR BASE
WITH 360 DEGREES OF ROTATION
2.75”
69.85mm
B.C.
1.19”
30.25mm
1.375”
34.92mm
.688”
17.46mm
ROTATION MOUNTING
PATTERN
ROTATION LOCKNUT
PLASTIC WASHER
ROTATION DISC
ROTATION PLATE
FLAT HEAD
MOUNTING SCREWS
PROVIDED
LAP TOP LOCK
VHB PAD
6.30”
160mm
PRIOR TO INSTALL OF VHB PAD
CLEAN BOTH MOUTING SURFACES
USING ALCOHOL PADS PROVIDED
MOUNTING SCREWS
NOT PROVIDED VHB PAD
1.77”
44.90mm
FIXED MOUNTING
PATTERN
MOUNTING SCREWS NOT PROVIDED
2.50”
63.50mmB.C.
1.77”
44.90mm

©
Compulocks Brands Inc. All Rights Reserved.j
www.compulocks.com | [e-mail] | [phone] Sheet 2 of 5
Assembly Instructions
Cling Stand SKU: UCLGSTDB \ UCLGSTDW
Movement Restrictions
Stand Assembly Rotation
STAND COVER
INSTALL STAND COVER
TIGHTEN ROTATION LOCKNUT
TO DESIRED ROTATION RESISTANCE
USING A 1/2” OR 13MM WRENCH
OPENS TO
8.50”
216mm
CLOSES TO
6.50”
165mm
* CAUTION*
WHEN INSTALLING TABLET
DO NOT OVER TIGHTEN TABLET RETAINERS
OVER TIGHTENING COULD LEAD TO
TABLET DAMAGE

©
Compulocks Brands Inc. All Rights Reserved.j
www.compulocks.com | [e-mail] | [phone] Sheet 3 of 5
Assembly Instructions
Cling Stand SKU: UCLGSTDB \ UCLGSTDW
Tablet Landscape Installation
WIRE MANAGEMENT
ROUTE POWER CABLE
THROUGH ARM
INSTALL TABLET AND
TIGHTEN AS SHOWN PRIOR
ATTACH POWER
CABLE TO TABLET
ROUTE CABLE
THROUGH CENTER HUB
PULL EXCESS POWER
CABLE
REMOVE CAP TO ROUTE CABLE
AFTER ROUTING CABLE REPLACE CAP
ROTATION
INSTALL REAR CAP
ROUTING CABLE THRU CAP

©
Compulocks Brands Inc. All Rights Reserved.j
www.compulocks.com | [e-mail] | [phone] Sheet 4 of 5
Assembly Instructions
Cling Stand SKU: UCLGSTDB \ UCLGSTDW
Tablet Portrait Installation
WIRE MANAGEMENT
INSTALL TABLET AND
TIGHTEN AS SHOWN PRIOR
ROUTE POWER CABLE
THROUGH CENTER HUB
OPTIONAL POWER CABLE
ROUTING
REMOVE CAP TO ROUTE CABLE
AFTER ROUTING CABLE REPLACE CAP
ATTACH POWER
CABLE TO TABLET
PULL EXCESS POWER
CABLE
INSTALL REAR CAP
ROUTING CABLE THRU CAP
OPTIONAL POWER
CABLE ROUTING
OPTIONAL POWER
CABLE ROUTING
ROTATION

©
Compulocks Brands Inc. All Rights Reserved.j
www.compulocks.com | [e-mail] | [phone] Sheet 5 of 5
Assembly Instructions
Cling Stand SKU: UCLGSTDB \ UCLGSTDW
Fixed Portrait or Landscape Adjustment
Wall Mounting
REMOVE COVER
PORTRAIT LANDSCAPE
TIGHTEN TENSION
SCREWS
REINSTALL
COVER
ROTATION RESISTANCE ADJUSTMENT
TIGHTEN ALL PHILLIPS FLAT HEAD SCREWS (3 PLACES)
THEN BACK OFF EACH OF THE SCREWS 1/4- 1/3 OF A TURN (3, PLACES)
FOR EASE OF ROTATION FROM LANDSCAPE TO PORTRAIT
MOUNTION SCREWS
NOT PROVIDED