conoptics 25A User manual

ConOptics, Inc. 19 Eagle Road, Danbury, CT 06810 Phone [phone] Fax [phone]
Email: [e-mail], or visit www.conoptics.com
1
Model 25A Manual
Introduction:
The Model 25A drive electronics is a high voltage push-pull linear power amplifier capable of
output voltage swings in the order of 145v P-P, push-pull. The Model 25A provides an output
frequency response from DC-25MHz and typical rise and fall times of 14ns.

ConOptics, Inc. 19 Eagle Road, Danbury, CT 06810 Phone [phone] Fax [phone]
Email: [e-mail], or visit www.conoptics.com
2
Technical Overview:
The Model 25A drive electronics is a DC coupled, RF differential amplifier. The amplifier is
capable of outputting 145volts peak-to-peak, push-pull into a 100 ohm balanced load. The
driver is designed to interface to Conoptics 2-port 100 ohms Electro-Optic Modulators and
beam deflectors. The amplifier has a forward gain of 43db (140) and requires only 1v p-p input
signal into 50 ohms to deliver its maximum output drive. The output section of the driver is
designed to drive a balanced transmission line with a characteristic impedance of 100 ohms.
The terminations for the transmission line are on the driver heat-sink and consist of two 50
ohm, 250w, thick film RF loads. The output signal of the amplifier is delivered to the E.O.
Modulator via 100 ohm twin-axial cable. This signal propagates through the modulator and
then returns to the driver to be terminated in the RF loads. There is little or no electrical power
dissipated in the E.O. Modulator. The output stage of the amplifier looks like a push-pull
current source, all the required DC and AC currents flow through the cables and the modulator.
Input Signal Requirements:
The Model 25A is DC coupled. Care should be taken in matching the input signal levels to that
described below and on the front panel. The front panel of the driver contains a peel-off label
instructing the user which of three different types of inputs the system is configured to accept.
As with any DC coupled amplifier, offsets in the signal format will be amplified to the same
degree that the actual signal content is, therefore this offset will reduce the overall dynamic
range of the amplifier by reducing its “headroom”. Typically, Most drivers when shipped are
configured to accept a “unipolar positive” input signal. In some cases, when dealing with an AC
coupled input signal from a signal source, the driver will be configured for a “bi-polar” input
signal. In very few cases, when dealing with inputs from high-speed D/A converters with
current outputs, the driver will be configured for a “unipolar-negative” input.
In any case, the driver may be configured to accept any one of the above inputs by the user if
the output requirements are other than that depicted by the front-panel placard.

ConOptics, Inc. 19 Eagle Road, Danbury, CT 06810 Phone [phone] Fax [phone]
Email: [e-mail], or visit www.conoptics.com
3
The above sketch depicts a unipolar positive input. This input format is the most common. If
there were some DC offset (non-zero) signal, the top end of the input might extend past +1.0v.
This could cause the amplifier to “rail” and introduce significant distortion in the output
waveform. If the output voltage required to drive the modulator to the desired level is less
than the maximum the amp can produce, then the DC offset may be ignored.
Note: If the amplifier is over-driven such that the output state goes into saturation and cut-off,
substantial “storage delays” may result. The amplifier may take hundreds of microseconds to
recover. Do not attempt to increase the input level beyond 1.0v limit.

ConOptics, Inc. 19 Eagle Road, Danbury, CT 06810 Phone [phone] Fax [phone]
Email: [e-mail], or visit www.conoptics.com
4
The above waveform depicts a bipolar or AC coupled input signal. If the duty cycle of the
waveform is always 50%, the DC term will stay at zero volts. If the duty cycle varies, so will the
DC term (dependent on the duty cycle). If the duty cycle varies, remember that this will be
seen by the driver as a varying DC signal and be amplified. This again may cause the amplifier
to “clip” and it will affect the operating point of the E.O. modulator, causing “bounce” in the
detected output. If the above input signal is DC coupled form the source, no precautions are
necessary.

ConOptics, Inc. 19 Eagle Road, Danbury, CT 06810 Phone [phone] Fax [phone]
Email: [e-mail], or visit www.conoptics.com
5
The unipolar negative waveform as shown above has the same requirements as the positive
case except that -1.0v would naturally be the most negative limit.

ConOptics, Inc. 19 Eagle Road, Danbury, CT 06810 Phone [phone] Fax [phone]
Email: [e-mail], or visit www.conoptics.com
6
Input waveform setup procedure:
The drive electronics operating point may be adjusted by the user to allow any of the three
previously discussed waveform types to be run in the system. A potentiometer labeled “DIF
BALL” (R44) allows the system to be setup for any input signal. The “pot” is located on the
driver PC board mounted on the inside of the rear panel. The control is on the left upper corner
of the board as faced from the front panel.
Note: No input signal should be connect to the driver input

ConOptics, Inc. 19 Eagle Road, Danbury, CT 06810 Phone [phone] Fax [phone]
Email: [e-mail], or visit www.conoptics.com
7
Unipolar Positive
R44 should be adjusted fully CW. Monitor T.P. # 1 & 2 on the right side of the DC power
connector J5 with a DVM. T.P. # 1 should read approximately 12vdc, T.P. 32 should read 49vdc
(both readings are with respect to gnd).
Bipolar
R44 is adjusted to make both T.P. # 1 & #2 equal. Each test point should read approx. 29vdc
with respect to gnd.
Unipolar Negative
R44 should be adjusted fully CCW. T.P. #1 should read approximately 49vdc, T.P. #2 should
read approximately 12vdc.
Test points # 1 & #2 may be used to examine the low frequency response of the driver. It
should be noted that each test point divides the signal at the load resistors by two. Also, these
test points have fairly high output impedance, 10K. Therefore, when looking at the AC
response of the driver, any load capacitance placed at the test points will affect the -3db
bandwidth of the test point. Typical scope probe input cap of 10pf will limit the bandwidth to
1.6MHz (Tr & Tf approximately 220ns). The signals at these test points may be summed by
inverting one channel of the scope and adding algebraically. This action closely duplicates what
the modulator sees electrically except for bandwidth and p-p signal.

ConOptics, Inc. 19 Eagle Road, Danbury, CT 06810 Phone [phone] Fax [phone]
Email: [e-mail], or visit www.conoptics.com
8
Common Mode ADJ (R31)
This potentiometer is factory set and should never need adjustment. Proper setting is T.P. # 1
& #2 = 30vdc with diff bal pot set to balance both test points.
Input Attenuator (R37)
This control allows the user to reduce the input level to the driver. Since the forward gain of
the amplifier is fixed and slightly greater than 140 (43db), some attenuation is required to keep
the amp in its linear range with a 1v p-p input.
Note:
It is recommended that this control is left in its factory position and an external attenuator be
used, if required, to limit the maximum input

ConOptics, Inc. 19 Eagle Road, Danbury, CT 06810 Phone [phone] Fax [phone]
Email: [e-mail], or visit www.conoptics.com
9
DC Bias Amplifier
This high voltage, differential, low frequency amp is included to allow the operator to adjust the
quiescent operating point of the E.O. modulator. The amplifier will deliver approximately +/-
400vdc of DC bias to allow the user to properly position the no-signal or 0v intensity of the
throughput beam exiting the modulator. This would typically be minimum transmission of the
modulator. Not only does this amplifier allow the user to position the operating point of the
modulator, but it also carries the low frequency content of the input waveform to the
modulator. The low frequency of DC terms are summed with the DC bias and delivered to the
modulator via the J3 connector on the rear panel of the driver. The 100 ohm balanced line is
AC coupled to the crystal in the E-O modulator. By connecting the information on J3 to the E-O
head, the optical response becomes completely DC coupled. Most of the electronics for the
high voltage amp are to the right side of the DC power connector J5.
Note:
There are hazardous voltages present in this area (-550VDC). There are no adjustments
required for this amplifier.