Conspit CGP User manual

CGP & CPP
Quick Guide
Ensu (Shanghai) Electronic Technology Co., Ltd

Contents
(a)
Mounting Plate
(d)
USB Cable
(g)
Optional PU Rubber
(h)
Allen bolt Spanners
(i)
(m8×20mm,m8×16mm)
(e)
Washer
(f)
lubricating oil
(c)
CONSPIT Stickers
(b)
Throttle, Brake and
Clutch Pedals

01 Mounting Demonstration
Heelrest
forward/backward
M8*20mm Allen bolt
M8*12mm Allen Bolt
Loosen two Allen bolts on the Heelrest,adjust
its position forward/backward.

02 Connection demonstration
Motor Set Only
USB to PC
To Conspit Base
Load cell pedals/handbrake
Hydraulic pedals/handbrake
Throttle clutch

03
Rubber replacement demonstration for CGP series
1. Loosen the adjusting ring (d) counterclockwise;
2. Unscrew the cylinder closure knob (e), take out the rubbers (c) and wasahers (b);
3. Dip an appropriate amount of lubricating oil with a cotton swab, apply it to the two
ends of the new rubber to be replaced and its edges, and seal both ends of the rubber
with gaskets of the corresponding size. The washer and the rubber are adhered to
each other by the viscosity of the lubricating oil, and put the two washers and one
rubber into the cylinder as a whole(g)；
4. After properly fitting the rubbers and washers, install the cylinder closure knob (e)
and adjusting ring (d); put the push rod against the washer and then slightly press it
down, so that the cylinder closure knob can be tightened easily；
5. Turn the adjusting ring (d) clockwise to increase the initial stiffness and shorten the
pedal travel range; turn the adjusting ring (d) counterclockwise to decrease the initial
stiffness and increase the pedal travel range.
Cylinder(a) Adjusting ring(d)
Cylinder closure knob(e)
Push rod(f)
PU rubbers(c)
Washer(b)
rubber and washers combination（g）

04
Rubber replacement demonstration for CPP series
1. Loosen the adjusting ring (d) counterclockwise;
2. Unscrew the cylinder closure knob (e), slightly press the brake pedal to take out the
rubbers (c) and washers (b)；
3.
Dip an appropriate amount of lubricating oil with a cotton swab, apply it to the two
ends of the new rubber to be replaced and its edges, and seal both ends of the rubber
with gaskets of the corresponding size. The washer and the rubber are adhered to
each other by the viscosity of the lubricating oil, and put the two washers and one
rubber into the cylinder as a whole(g)；
4. After properly fitting the rubbers (c) and washers (b), install the cylinder closure
knob (e) and adjusting ring (d)；
5. Turn the adjusting ring (d) clockwise to increase the initial stiffness and shorten the
pedal travel range; turn the adjusting ring (d) counterclockwise to decrease the initial
stiffness and increase the pedal travel range.
Cylinder(a) Adjusting ring(d)
Cylinder closure knob(e)PU rubbers(c)
Washer(b)
* Due to the ductility of the piston material inside the hydraulic
cylinder,CPP brake need to be used for a period of time to
eliminate the sense of resistance caused by friction.
rubber and washers combination（g）

05 Brake Stiffness level Suggestion
firmest pedal feel
softest pedal feel
rotate the throttle pedal adjustment ring
clockwise to decrease pedal travel range,
rotate it counterclockwise to increase
pedal travel range.
*Baseline setup is level 1
16mm
bright yellow
16mm
bright yellow
16mm
light yellow
16mm
light yellow
18mm
bright yellow
18mm
bright yellow
18mm
light yellow
18mm
light yellow
CONSPIT







1

4




6
4


8

6
8

light yellow bright yellow

Firmware upgrade
Hydraulic/load cell
switching button
Clutch motor operation range
(optional with clutch motor)
Press pedal to the maximum
then click “Max” button
Fully release the pedal then click “Min” button
06 CONSPIT link Calibration

07 CGP/CPP mounting templates




 

#GET YOURSELF IMMERSED
CONSPIT.COM
