Behringer PB600 User manual

behringer.com
Stompbox Accessories
PEDAL BOARD
PB600
Pedal Board with 9 V DC Power Supply
and Patch Cables
* Depends on the power consumption
of the eects pedals, etc.
Ultra-compact and lightweight
pedal board for transporting up
to 6 eects pedals, including
patch cables
Generous 1.7 A power adapter
included for powering more
than 12 devices*—includes
1 x 6 daisy-chain cabling
Ultra-rigid plastic design withstands
even heavy impact
High-quality components and
exceptionally rugged construction
ensure long life
Conceived and designed by
BEHRINGER Germany
When eects are an integral part of your
rig, their power adapters and patch cables
can often be the most vulnerable part, and
the most likely to sabotage your set if
they're not pampered. Rather than tossing
your pedals, power adapters and all
other cabling into a duel bag after a gig,
keep them safe—and ready to rock at a
moment’s notice—with the PB600.
It's all about connections
This awesome pedal board makes
hooking up six 2.5" x 4.5" pedals as easy
as hooking up just one (of course, if
you're using pedals that aren’t 2.5" x 4.5",
the snug foam padding can be cut to
accommodate pedals of varying shapes).
The PB600 includes ¼" patch cables, so you
can leave your pedals connected to one
another, ready to pass signal even when
you’re transporting them. It also comes
with 1 x 6 daisy chain cabling so that when
you plug in the 1.7 A power adapter, all
your pedals receive power. Meanwhile,
all cabling remains safe and free of strain.
Failure is almost guaranteed when you’re
dealing with a rat’s nest of loose cabling,
but with the PB600, your eects chain is
always safe and organized.
Connect your guitar, bass or keyboard
to the single ¼" input in the upper right
corner of the board. A pair of ¼" FROM
EFFECTS jacks in the upper left corner
allow you to connect stereo eects, and
two ¼" OUTPUT TO AMP jacks send a left
and right stereo signal to up to two amps.
Continued on next page

Page 2 of 3
VD400 CS400
HB01
EQ700DR600 BO300 CS400
HB01
PH9 TO800 EQ700
VT100FX
412H-BK
BUGERA 333XL
ACX900
VT30FX
AM100
UM300
VT100FXH
412H-BK
Hookup Diagram
PEDAL BOARD
PB600
When it’s time to load out, just unplug
the power supply, disconnect your guitar
and amp, put the lid back on the PB600
and slide the locking latches back into
place. The heavy-impact plastic casing will
protect your pedals from the very worst
dings, scrapes and scratches the road
throws your way.

Page 3 of 3
©2010 Red Chip Company Ltd.Technical specifications and appearance subject to change without notice.The information contained herein is correct at the time of printing. BEHRINGER accepts no liability
for any loss which may be suffered by any person who relies either wholly or in part upon any description, photograph or statement contained herein. 985-10000-00382 behringer.com
For service, support or more information contact the BEHRINGER location nearest you:
Europe Tel.: [phone], Fax: [phone]
USA/Canada Tel.: [phone], Fax: [phone]
Singapore Tel.: [phone], Fax: [phone]
Australia Tel.: [phone], Fax: [phone]
Japan Tel.: [phone], Fax: [phone]
DC OUT
connector
powers all eects
via daisy chain
1.7 A power
adaptor
connector
DC cabling
duct
Heavy-duty
plastic
casing
Sliding locks
hold lid rmly
in place when
pedal board is
not in use
¼" TS INPUT connector
receives signal from
instrument.
¼" TS TO EFFECTS
connector sends signal
to eects pedals
Foam padding
holds eect
pedals in place
FROM EFFECTS
connectors receive
stereo signal from
pedals. OUTPUT TO AMP
connectors send signal
to two amps
SPECIFICATIONS
Power Supply 9 V, 1.7 A switching adaptor(included)
Connectors ¼" TS, unbalanced
USA/Canada 120 V~, 60 Hz
GPE182-090170-1 (HSB-UL)
Europe/Australia 230 V~, 50 Hz
GPE182-090170-2 (HSB-EU)
U.K. GPE182-090170-3 (HSB-UK)
Korea 220 V~, 60 Hz
GPE182-090170-4 (HSB-SAA)
China 220 V~, 50 Hz
GPE182-090170-5 (HSB-CCC)
Japan 100 V~, 50/60 Hz
GPE182-090170-6 (HSB-JP)
Power connector 2 mm DC jack, center negative
(with daisy-chain cable included)
Power consumption 2 mA
PHYSICAL
PB1000
Dimensions 504.3 x 663.6 x 115 mm
(HxWxD) 19 / x 2 6 ⁄ x 4 ½"
PB600
Dimensions 13 x 26 ⁄ x 4 ½"
(HxWxD) 329 x 663.6 x 115 mm
PB1000
Weight approx. 11.8 lbs / 5.3 kg
including PSU & daisy chain
PB600 approx. 8.4 lbs / 3.8 kg
including PSU & daisy chain
BEHRINGER is constantly striving to maintain the highest professional standards. As a result of these eorts,
modications may be made from time to time to existing products without prior notice. Specications and
appearance may dier from those listed or illustrated.
PEDAL BOARD
PB600