Ver.1.00
FA-UNIT-M11BE 1
Wall-Mount / Desk-Top Chassis
for SBCs
FA-UNIT-M11BE
*Specifications, color and design of the products are subject to
change without notice.
This product is a chassis used to mount a backplane and SBC
and configure a computer system in combination with
expansion boards and various drives.
PICMG compliant, PCI/ISA bus backplane can be mounted.
Equipped with 5-inch-drive bay x 1 and 3.5-inch drive bay x 2
(one is a shadow bay).
Equipped with a power switch, and reset switch at the front.
Equipped with a built-in cooling fan. The dustproof filter and
cooling fan can be replaced externally (rear fan).
These fans can easily be replaced externally, without removing
the top cover.
A chassis fixing bracket is attached as standard.
Backplanes and mother boards are sold separately. You need
prepare a CONTEC backplane corresponding to this product,
separately. For more details of the corresponding backplanes,
see "Option".
When using a third-party's backplane or motherboard, pay
attention to the positions of the backplane or motherboard
installation holes, installable size, and power supply
specifications of this product.
This product has a space that can contain one 5-inch drives
and two 3.5-inch drives.
Chassis [FA-UNIT-M11BE] …1
Power cable…1
Rubber pads…4
Screws (for Rubber pads) (M4x8)…4
Screws (used for expansion bay fixing and board installation)
(M3 x 6)…26
Screws (for HDD) (#6-32UNC x 5)…8
Hexagon spacer…11
Plastic Spacers…3
Bracket for wall-mounted…2
Slot cover…11
User’s Manual…1
General specifications
Item Specification
Number of user slots 11 middle-size slots
Installable board (mm) Middle-size : 224.0(L) x 122.0(H) (Max.)
Rack mountable Impropriety
Fan Inlet x 1
(Excluding power supply fan)
Drives 5-inch x 1,
3.5-inch x 2 (one is a shadow bay)
Number of slot holes 11
Installable Backplane
dimensions (mm) 246.4(W) x 243.8(D) (Max.)
BPC-1111
Dimensions (mm) 435(W) x 177(H) x 315(D) (Excluding raised parts)
Weight About 10kg (Excluding motherboard, drives, etc.)
Power supply specifications
Item Specification
Power capacity *1 +5V 25A -5V 0.3A
+3.3V 25A -12V 0.8A
+12V 15A +5VSB 2A
Overall maximum
power supply capacity 300W
AC Power Voltage *2 115VAC/230VAC(50/60Hz) (SW selection)
Input current 10A(115VAC)/5A(230VAC)
AC Outlet None
*1 Total of +5V and +3V shall not exceed the power of 200W.
*2 Input voltage range forAC power supply : 90 - 132VAC / 180 - 250VAC
Environmental specifications
Item Specification
Operating temperature 0 - 50°C
Operating humidity 10 - 80%RH(No condensation)
Storage temperature 0 - 60°C
Storage humidity 10 - 90%RH(No condensation)
Vibration resistance 10 - 57Hz/semi-amplitude 0.075mm 57 - 150Hz/1.0G *3
Impact resistance 10G, half-sine shock for 11 ms *3
Floating dust particles Not to be excessive
Corrosive gases None
*3 This value is for the horizontal placement. Avoid the vertical placement in the
environments where any sources of vibration or impact exist.
* The values in the above are constrained with the boards or the components such as
drives installed inside the product, so the figures do not necessarily represent the
tolerances for every operating condition.
SpecificationFeatures
Configuration
Packing List
