Control Concepts Fusion User manual

FUSION REMOTE DISPLAY KIT
DESCRIPTION
The remote display kit includes all necessary components (excluding
knockout punch) to mount the display to the front of an electrical
enclosure. This allows for easy viewing and adjustment of parameters
and reduces costs by eliminating the need for external gauges.
The remote display meets CE and UL requirements. CE testing was
conducted with a 25 foot cable from the controller to the display.
Contact the factory if you require a length longer than 25 feet.
MOUNTING CONSIDERATIONS
Must be mounted on enclosure with smooth surface.
Maximum panel thickness: 0.25 [6.4].
RATINGS
• IP65 - Totally protected against
ingress of dust. Protected against
jets of water. Limited ingress
permitted.
• UL Type 1 - Enclosure constructed
for indoor use to provide a
degree of protection to personnel
against incidental contact with
the enclosure equipment and to
provide a degree of protection
against falling dirt.
• UL Type 12 - Enclosures
constructed (without knockouts)
for indoor use to provide a degree
of protection to personnel against
incidental contact with the enclosed
equipment; to provide a degree
of protection against falling dirt,
againstcirculatingdust,lint,bers,
andlings;againstdrippingand
light splashing of non-corrosive
liquids; and against light splashing
and consequent seepage of oil and
non-corrosive coolants.
321
MOUNTING INSTRUCTIONS
Mounting Kit includes:
(1) Gasket (1) Ferrite
(1) Display retainer (4) Screws
(1) 5 or 25 foot shielded cable
(1) Empty Display with CCI logo to replace actual display
1. Carefully remove the 4 screws securing the lid.
2. Disconnect the display cable from the controller. (See Fig. 1)
3. Remove the display from the lid. The four tabs holding the
display into the lid are marked. (See Fig. 2)
4. Insert the empty display into the lid and reattach to the
controller.
5. Remove the 1 foot cable from the display. Run one end of
the 5 or 25 foot cable to the Remote Display connector on the
side of the controller (See Number 3)
FUSION Remote Display Kit Guide © Control Concepts Inc., 2013
www.ccipower.com 1-800-765-2799

6. Make a 1/4 DIN (3.627” x 3.627” [92.13mm x 92.13mm]) size hole in the cabinet. (See guide below.)
7. Place the gasket on the back of the display. Make sure the gasket does not overhang the edges of the
display. Place the display inside of the 1/4 DIN cutout of the cabinet with the display facing outward.
8. Attach the other end of the 5 or 25 foot shielded cable to the connector on the display. Place the ferrite as
close to the connector as possible. (See Number 4)
4
9. Attach the display retainer with provided mounting screws. When
tightening down the display make sure to apply equal pressure to each
screw to ensure the gasket seals properly. When properly installed the
gasket shall be compressed 50% on all sides. If the gasket becomes
damaged during installation please contact Control Concepts for a
replacement.
When the controller is supplied with the Universal input power [100-240 Vac]
the display shall now operate the same as when mounted on the controller.
1/4 DIN HOLE GUIDE
Usethefollowingoutlinetocutthe1/4DINsizehole,asspeciedinStep6.
3.627
[92.1]
3.627
[92.1]
1/4 DIN Knockout
CONTACT
TEL: [phone] | [phone]
FAX: [phone] | www.ccipower.com
18760 Lake Drive East, Chanhassen, MN 55317, USA
CONTROL
CONCEPTS
FUSION Remote Display Kit Guide © Control Concepts Inc., 2013
www.ccipower.com 1-800-765-2799