Coolworks MPPDB-09HRN1-BCG5 User manual

Model/modèle :MPPDB-09HRN1-BCG5

Preparation.............................................................................................................................................2
Safety Precautions.................................................................................................................................3
Cautions..................................................................................................................................................4
Installation..............................................................................................................................................5
Operation................................................................................................................................................9
Maintenance.........................................................................................................................................14
Faults Diagnosis..................................................................................................................................15
Design and Compliance Notes...........................................................................................................16
Sociable Remark.................................................................................................................................17
Remote Controller Illustration............................................................................................................18
Air Conditioner Limited Warranty...........................................................................................................31
Contents

Preparation
front
control panel
handle
(both sides)
horizontal louver
blade
(swing automatically)
Caster
rear
power plug socket
power cord buckle
bottom tray
drain outlet
power cord outlet
drain outlet
(only for pump
heating mode)
upper air filter
(behind the grille)
upper air intake
air outlet
lower air filter
lower air intake
drain outlet
SCALE 0.500

Safety Precautions
-Installation must be performed according to the installation instructions. Improper installation
can cause water leakage, electrical shock, or fire.
-Use only the included accessories and parts, and specified tools for the installation. Using
non-standard parts can cause water leakage, electrical shock, fire, and injury or property
damage.
-Make sure that the outlet you are using is grounded and has the appropriate voltage. The
power cord is equipped with a three-prong grounding plug to protect against shock. Voltage
information can be found on the side of the unit, behind the grille.
-Install the unit in on a flat, sturdy surface. Failure to do so could result in damage or excessive
noise and vibration.
-The unit must be kept free from obstruction to ensure proper function and to mitigate safety
hazards.
-DO NOT modify the length of the power cord or use an extension cord to power the unit.
DO NOT share a single outlet with other electrical appliances. Improper power supply can
cause fire or electrical shock.
-DO NOT install your air conditioner in a wet room such as a bathroom or laundry room. Too
much exposure to water can cause electrical components to short circuit.
-DO NOT install the unit in a location that may be exposed to combustible gas, as this could
cause fire.
-The unit has wheels to facilitate moving. Make sure not to use the wheels on thick carpet or
to roll over objects, as these could cause tipping.
-DO NOT operate a unit that has been dropped or damaged.
-Only use the included accessories and specified parts for installation. Using nonstandard
parts can cause water leakage, electrical shock, fire, and injury or property damage.
-The unit must be kept free from obstruction to ensure proper function.
-DO NOT allow children to play with the air conditioner. Children must be supervised around
the unit at all times.
-If the air conditioner is knocked over during use, turn off the unit and unplug it from the main
power supply immediately. Visually inspect the unit to ensure there is no damage. If you
suspect the unit has been damaged, contact a technician or customer service for assistance.
-In a thunderstorm, the power must be cut off to avoid damage to the machine due to lightning.
Please read through these instructions before you start the installation process.
Improper installation can cause damage to the unit, your personal property, and
also poses a personal safety hazard.

Cautions
-This appliance can be used by children aged from 8 years and above and person with reduced
physical, sensory or mental capabilities or lack of experience and knowledge if they have been
given supervision or instruction concerning use of the appliance in a safe way and understand
the hazards involved. Children shall not play the appliance. Cleaning and user maintenance
shall not be made by children without supervision.(be applicable for the European Countries)
-This appliance is not intended for use by persons (including childern) with reduced physical,
sensory or mental capabilities or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance by a person responsible for
their safety. (be applicable for other countries except the European Countries )
-Children should be supervised to ensure that they do not play with the appliance.
-If the supply cord is damaged, it must be replaced by the manufacturer,its service agent or
similarly qualified persons in order to avoid a hazard.
-Prior to cleaning or other maintenance, the appliance must be disconnected from the supply
mains.
-Do not install the appliance in a location that may be exposed to combustible gas.
-If combustible gas accumulates around the unit, it may cause fire.
-Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings.
Do not route cord under furniture or appliances. Arrange cord away from traffic area and where
it will not be tripped over.
-Do not operate unit with a damaged cord or plug. Discard unit or return to an authorized service
facility for examination and/or repair.
-To reduce the risk of fire or electric shock, do not use this fan with any solid-state speed control
device.
-The appliance shall be installed in accordance with national wiring regulations.
-Contact the authorised service technician for repair or maintenance of this unit.
-Contact the authorised installer for installation of this unit.
-When there are wide differences between "USER' S MANUAL" and "Remote controller
Illustration" on function description, the description on "USER' S MANUAL " shall prevail.
-Do not operate your air conditioner in a wet room such as a bathroom or laundry room.

Installation
Choosing The Right Location
Your installation location should meet the following
requirements:
-Make sure that you install your unit on an even
surface to minimize noise and vibration.
-The unit must be installed near a grounded plug,
and the Collection Tray Drain (found on the back
of the unit) must be accessible.
-The unit should be located at least 30cm (12”) from
the nearest wall to ensure proper air conditioning.
-DO NOT cover the Intakes, Outlets or Remote
Signal Receptor of the unit, as this could cause
damage to the unit.
Note About Fluorinated Gasses
-This air-conditioning unit is a hermetically sealed unit that contains fluorinated gasses. For
specific information on the type of gas and the amount, please refer to the relevant label on
the unit itself.
-Installation, service, maintenance and repair of this unit must be performed by a certified
technician.
-Product uninstallation and recycling must be performed by a certified technician.
-If the system has a leak-detection system installed, it must be checked for leaks at least
every 12 months.
-When the unit is checked for leaks, proper record-keeping of all checks is strongly
recommended.
All the illustrations in the manual are for explanation purpose only. Your machine may be
slightly different. The actual shape shall prevail.The unit can be controlled by the unit control
panel alone or with the remote controller. This manual does not include Remote Controller
Operations, see the <<Remote ControllerInstruction>> packed with the unit for details.
NOTE:

Installation
Tools Needed
-Medium Philips screwdriver; -Tape measure or ruler; -Knife or scissors;
-Saw (optional, to shorten window adaptor for narrow windows)
Accessories
Your Window Installation Kit fits windows 67.5-123cm(26.5-48”) and can be shortened for
smaller windows.
Window Installation Kit Step One:
Preparing the Exhaust Hose
assembly
Press the exhaust hose into the window
slider adaptor and unit adaptor, clamp
automatically by elastic buckles of the
adaptors.
Insert unit adaptor of the Exhaust hose assembly
into the lower groove of the air outlet of the unit
while the hook of the adaptor is aligned with the
hole seat of the air outlet and slide down the
Exhaust hose assembly along the arrow direction
for installation.
Step Two: Install the Exhaust hose
assembly to the unit
Part Description
1 pc
1 pc
1 pc
1 pc
1 pc
1 pc
1 pc
1 pc
1 pc
2 pc
2 pc
1 set
1 set
Unit Adaptor
Window Slider Adaptor
Window Slider A
Eand c axhaust Hose
Bolt
Foam Seal A (Adhesive)
Foam Seal B (Adhesive)
Foam Seal C (Non-adhesive)
Security Bracket and 2 Screws
Drain Hose
Drain Hose Adaptor(only for
heat pump mode)
Quantity
Remote Controller and Battery
(For remote control models only)
ON/OF F
TEMP
SHORT
CUT
TIMER ON TIMER OFF
MODE
FAN
SLEEP S WING LE D
Unit adaptor Window slider
adaptor
Exhaust hose Exhaust hose
assembly Hook Hole Seat
Lower groove
adaptor Make sure the adaptor is
inserted into the lower
groove of the air outlet.
Window Slider B and C

Installation
Step Three: Preparing the
Adjustable Window Slider
1. Depending on the size of your window,
adjust the size of the window slider.
2. If the length of the window requires two
window sliders, use the bolt to fasten the
window sliders once they are adjusted to
the proper length.
Note: Once the Exhaust Hose assembly and Adjustable Window Sliderare prepared,
choose from one of the following two installation methods.
Cut the adhesive foam seal
A and B strips to the proper
lengths, and attach them to
the window sash and frame
as shown.
Insert the window slider
assembly into the window
opening.
Insert the window slider
adaptor into the hole of
the window slider.
Cut the non-adhesive foam
seal C strip to match the width
of the window. Insert the seal
between the glass and the
window frame to prevent
airand insects from getting into
the room.
Type 1: Hung Window Installation
Foam seal B
(Adhesive type-shorter)
Foam seal A
(Adhesive type)
Window slider A
Window slider B
(if required)
Foam seal C
(Non-adhesive type)
If desired, install the
securitybracket with
2 screws as shown.
2 Screws
Security Bracket
Window slider A Window slider B
Bolt Bolt
Window slider C

Installation
Cut the adhesive foam seal
A and B strips to the proper
lengths, and attach them to
the window sash and frame
as shown.
If desired, install the
securitybracket with
2 screws as shown.
Insert the window slider
adaptor into the hole of
the window slider.
Insert the window slider
assembly into the window
opening.
Cut the non-adhesive foam
seal C strip to match the
window height. Insert the
foamseal between the glass
and the window frame to
prevent airand insects from
getting into the room.
Type 2: Sliding Window Installation
Note: To ensure proper function, DO NOT overextend or bend the hose.
Make sure that there is no obstacle around the air outlet of the exhaust
hose (in the range of 500mm) in order to the exhaust system works
properly. All the illustrations in this manual are for explanation purpose
only. Your air conditioner may be slightly different. The actual shape shall
prevail.
Foam seal B
(Adhesive type-shorter)
Foam seal A
(Adhesive type)
Window slider A
Window slider B
(if required)
Foam seal C
(Non-adhesive type)
2 Screws
Security
Bracket

Operation
Swing button(optional)
(Applicable to the models with
auto swing feature only)
Used to initiate the Auto swing
feature. When the operation is
ON, press the SWING button
can stop the louver at the
desired angle.
Timer button
Used to initiate the AUTO ON
start time and AUTO OFF stop
time program, in conjuction with
the + & - buttons. The timer on/off
indicator light illuminates under
the timer on/off settings.
Mode button
Selects the appropriate operating
mode. Each time you press the
button, a mode is selected in a
sequence that goes from AUTO,
COOL, DRY, FAN and HEAT
(cooling only models without).The
mode indicator light illuminates
under the different mode settings.
Up (+) and Down (-) buttons
Used to adjust (increasing/decreasing)
temperature settings in 1°C/1°F
increments in a range of 17°C/62°F to
30°C/86°F or the TIMER setting in a
range of 0~24hrs.
NOTE: The control is capable
of displaying temperature in
degrees Fahrenheit or degrees
Celsius. To convert from one
to the other, press and hold
the Up and Down buttons at
the same time for 3 seconds.
Fan/Ion button(Ion is optional)
Control the fan speed. Press to select the
fan speed in four steps-LOW, MID, HIGH
and AUTO. The fan speed indicator light
illuminates under different fan settings.
NOTE: Press this button for 3 seconds to
initiate ION feature. The ion generator is
energized and will help to remove pollen
and impurities from the air, and trap them
in the filter. Press it for 3 seconds again to
stop the ION feature.
Sleep/Eco button
Used to initiate the SLEEP/ECO
operation.
Power button
Power switch on/off.