Cooper Menvier Scantronic 9651 User manual

USER GUIDE
HARDWIRED
CONTROL UNIT

Page 2 497282
Contents
1. Introduction ........................................3
Alarm System.......................................3
Keypad.................................................4
Proximity Tags .....................................4
Mains Power Failures...........................7
About this Guide...................................8
2. Everyday Operation ...........................9
Setting the System...............................9
General Procedure.........................10
Timed Set.......................................11
Final Door Set ................................11
Lock Set .........................................11
Terminated Set...............................11
Silent Set........................................11
Instant Set......................................11
Keyswitch Set.................................12
Forbikobler Keypad Set..................12
Investigating Setting Problems...........13
Detector Active...............................13
Other Problems..............................14
Unsetting the System .........................15
General Procedure.........................15
Keyswitch Unset.............................15
Aborting False Alarms ................... 16
3. After an Alarm.................................. 17
Responding to a Fire Alarm............... 17
Responding to other Alarms .............. 17
4. Special Functions............................ 18
Introduction........................................ 18
Viewing Alerts.................................... 19
Omitting Zones .................................. 20
Normal Alarm Zones...................... 20
24-hour Zones ............................... 20
Requiring User Code before
Installer Code .................................... 21
Reading the Log ................................ 21
Turning the Chime On and Off .......... 22
Testing the Sounders ........................ 22
Testing Zones.................................... 23
Setting up Users................................ 23
Access Codes ............................... 24
Proximity Tags............................... 26
Setting Time and Date....................... 26
Appendix. Log Messages ................... 27
Your Installation .................................. 32
9651 Hardwired Control Unit User Guide.
This document applies to control panels using software version 4.x.
© Cooper Security Ltd. 2005
Every effort has been made to ensure that the contents of this book are correct. However, neither the authors
nor Cooper Security Limited accept any liability for loss or damage caused or alleged to be caused directly or
indirectly by this book. The contents of this book are subject to change without notice.
Printed and published in the U.K.

497282 Page 3
1. Introduction
Alarm System
The alarm system described in this book comprises a control unit (model
9651), one or more keypads, and various detectors. The control unit houses a
main controller, power supply, stand-by battery and an optional
communication device. It is normally fitted in a safe place out of sight (for
example, under the stairs).
The detectors are installed in various places, or zones, around the premises.
If something triggers a detector, the detector signals this to the control unit.
How the control unit reacts depends on whether the system is set or unset.
• When set, the control unit raises an alarm whenever a detector is
triggered. The alarm might be a bell or strobe on the outside of your
premises, or it might be a silent signal over the telephone line to an Alarm
Receiving Centre (ARC).
• When unset, the system does not raise an alarm if a detector is triggered.
• Your installer can program the control unit so that you can set the system
to one of four levels: A, B, C or D. Level A protects the whole of the
premises covered by the detectors. Levels B, C and D each protect part
of the premises while the rest is in use. You cannot set more than one
level at the same time.
The control unit raises an alarm when a detector in a set level is triggered.
Your installer allocates detector zones to levels during installation. Refer to
the table on page 32 to see how zones are allocated.
Your premises may be fitted with 24-hour zones and panic alarm zones. If
these zones are triggered, the system will raise an alarm even if no level is
set. 24-hour zones are often used to protect emergency fire exits.

1. Introduction
Page 4 497282
Keypad
Your alarm system is fitted with a 9930 or 9940 keypad, from which you can
set and unset the system. Figures 1 and 2 show the main features of these
keypads. Refer to "4. Special Functions" on page 18 for information about
other functions available from them.
The system will not accept commands from the keypad until you identify
yourself with an access code or proximity tag. It can store 50 access codes,
which may contain four or six digits1, giving secure access for up to 50 users.
If you enter an incorrect code, press Xto clear the display and try again. If you
enter an incorrect code four times, all keypads will be locked for 90 seconds.
If you do not enter a command within 20 seconds, the system leaves
command mode. You will need to enter your code again to continue.
Your installer may have set up your system to hide status information2. If so,
the display and lamps show no information until you identify yourself. This
prevents status information being used to compromise system effectiveness.
Proximity Tags
So that you do not have to remember access codes, your installer may have
fitted your keypads with a device that reads proximity tags. These tags are
small slips of plastic that have electronic circuitry built into them.
When you hold a tag against a suitably equipped keypad, the circuit inside the
tag emits a radio code that the keypad reads. Each tag has a unique code. If
the alarm system recognises the tag, it allows you to do almost anything that
you could do with an access code. If the tag is not recognised, you cannot use
the alarm system. When presenting a tag to a 9930 keypad, make sure that it
is touching the sensitive area to the left of the display (Figure 1). The 9940
keypad has a proximity coil that makes the whole case sensitive to tags.
You can program the system to recognise up to 49 tags. U01, the master
user, can only be assigned an access code – a proximity tag cannot be
assigned to this user. For instructions, refer to page 25.
1Installer Command 56
2Installer Command 28

1. Introduction
497282 Page 5
Figure 1. 9930 LCD Remote Keypad
Alert lamp (see page 20)
Flashes to highlight
unacknowledged alarm,
fault or tamper conditions.
Glows for acknowledged
conditions.
Goes out when all
conditions are rectified.
Service lamp
Glows if the
system needs
an Installer
reset.
Mains lamp
Glows when
using mains
power.
Flashes when
using stand-by
battery.
Sensitive area
Present
proximity tags
by touching
them to this
area.
2-line 16-digit liquid
crystal display
The first line shows:
- unset: time and date
- set: level(s) .
The second line shows
Installer-configured text,
often the control unit
model number.
The display may show
only time and date until
a user is identified.
Exit key
Press to
cancel a
command
sequence.
Enter key
Press to
confirm a
command
sequence.
IMPORTANT NOTE
Dual key alarms
Pressing two keys
together can initiate
alarms if these are
enabled (see page 32).
Panic
Press 1 and 3 together.
Medical assistance
Press 4 and 6 together.
Fire
Press 7 and 9 together.
These may show nothing until a user is identified.
Level selection
keys
Press to select
levels.

1. Introduction
Page 6 497282
Figure 2. 9940 LCD Remote Keypad
AB CD
123
456
7890
Alert lamp (see page 20)
Flashes to highlight
unacknowledged alarm,
fault or tamper conditions.
Glows for acknowledged
conditions.
Goes out when all
conditions are rectified.
Service lamp
Glows if the
system needs
an Installer
reset.
Mains lamp
Glows when
using mains
power.
Flashes when
using stand-by
battery.
2-line 16-digit liquid
crystal display
The first line shows:
- unset: time and date
- set: level(s).
The second line shows
Installer-configured text,
often the control unit
model number.
The display may show
only time and date until
a user is identified.
Exit key
Press to
cancel a
command
sequence.
Enter key
Press to
confirm a
command
sequence.
IMPORTANT NOTE
Dual key alarms
Pressing two keys
together can initiate
alarms if these are
enabled (see page 32).
Panic
Press 1 and 3 together.
Medical assistance
Press 4 and 6 together.
Fire
Press 7 and 9 together.
These may show nothing until a user is identified.
Level selection
keys
Press to select
levels.

1. Introduction
497282 Page 7
Mains Power Failures
The control unit indicates mains power failures using alerts. If the supply has
since been restored, the alert will show the condition as inactive. For
instructions on how to view and acknowledge alerts, refer to page 19.

1. Introduction
Page 8 497282
About this Guide
The rest of this guide tells you how to use the system:
2. Everyday Operation Tells you how to set and unset the system.
3. After an Alarm Tells you how to switch off the sounders after an
alarm, view what caused the alarm and reset the
system so that it can be used again.
4. Special Functions Tells you how to use more advanced features, some
of which are available only to the master user.

497282 Page 9
2. Everyday Operation
During installation, your installer programs the system to create an exit route
and entry route for your premises. When setting the system, you must follow
the exit route. When unsetting the system, you must follow the entry route. If
you stray from these routes, you may cause a false alarm.
Setting the System
There are several different methods for setting the system. Each level can use
a different method, although not all methods are available in all cases. Your
installer will have selected the methods that suit your site best3.
The possible setting methods are:
Timed Set Silent Set
Final Door Set Instant Set
Lock Set Keyswitch Set
Terminated Set
The setting procedure is similar for each method and shown on page 10.
Subsequent sections describe the specifics of each setting method.
If you try to set the system while something is triggering a detector in the
protected area (for example a door or window is still open), the system will not
set (see page 13).
If you find that your detectors generate false alarms immediately after you
leave the premises, this may be because they are detecting air movements
when the exit door is closed. You may need to ask your installer to increase
the Final Exit Settling Time4.
3Installer Commands 39, 62, 72 and 76
4Installer Command 182

2. Everyday Operation
Page 10 497282
General Procedure
To set the system:
1. Secure all doors and windows.
2. At the keypad, key in an access code
(or present a tag).
The display shows (for example): System OK
Set?
3. Press the appropriate level key.
Note: If you press ywithout a level key, the
system sets Level A (Full Set).
4. If you have omitted a zone (see page 20),
the display shows (for example): Omit Zone 03?
Set? ABCD
Press yto continue with the zone omitted.
If you do not want to omit it, press Xto exit.
During the exit procedure, the keypads give
a continuous exit tone. The tone may be
intermittent if the final door is open.
Setting ABCD 009
If you hear an intermittent tone from the
keypads or internal sounder and the final
door is not open, a detector is being
triggered (see page 12).
5. Leave by the designated exit route.
When you complete the exit procedure in
accordance with the setting method in use,
the system sets and gives a double "beep".
The keypad display shows which level is
set.
Set ABCD
9x5x
Set A
9x5x
Note:If you decide not to set the system, key in your
access code again (or present a tag) to unset it.

2. Everyday Operation
497282 Page 11
Timed Set
With Timed Set, the system sets after a programmed exit time has expired.
The time starts when you press a level key, or when you press yto accept an
omitted zone. Your installer will have made the exit time long enough for you
to leave the premises and secure the final door5.
When using Terminated Set (see below), your installer may have
programmed the system to set after the exit time even if the exit terminate
button is not pressed. This ensures your premises are protected if you forget
to press the button.
Final Door Set
Your installer may have programmed the system so that closing the final door
completes the setting sequence. The system sets 7–12 seconds6after you
secure the final door. There is no fixed exit time.
Lock Set
Your installer may have fitted a special lock so that locking the final door
completes the setting sequence. The lock contains a switch so that the control
unit can sense whether the lock is open or closed. The system sets seven7
seconds after you lock the final door. There is no fixed exit time.
Note:Lock Set is available only for Level A (Full Set).
Terminated Set
Your installer may have fitted an exit terminate button. This is usually outside,
beside the final door, and you press it when you leave. The system sets
seven8seconds after you press the button. There is no fixed exit time.
Silent Set
Some levels on your system may be programmed for Silent Set. The system
does not give an audible warning when it sets these but it gives a double
"beep" at the end of the exit time to show that it is set.
Note:Silent Set is not available for Level A (Full Set).
Instant Set
The area protected by a level may not need an exit route or final door. With
Instant Set, the system sets as soon as you press the appropriate key, without
5Installer Commands 44, 65, 75 and 79
6Installer Command 182
7Installer Command 182
8Installer Command 182

2. Everyday Operation
Page 12 497282
waiting for an exit time. The system gives a double "beep" to show that it is
set.
Note:Instant Set is not available for Level A (Full Set).
Keyswitch Set
If your system is fitted with a keyswitch, you can use it to set the system. If it
is a three-position keyswitch in a single system, you can use it to set Level B.
The keyswitch initiates setting, which then completes in accordance with the
programmed exit mode. You do not need to enter an access code or present
a tag.
Forbikobler Keypad Set
Your system may be programmed to use a special type of entry or exit zone
called a Forbikobler zone. The word "forbikobler" means "bypass" in Danish.
These zones are used to connect external keypads or access controllers.
If an exit is programmed as a Forbikobler zone with an external keypad, a
trigger from the keypad within the exit time stops the timer and sets the
system.

2. Everyday Operation
497282 Page 13
Investigating Setting Problems
This section offers general guidance. If you need assistance to resolve a
problem, contact your installer.
Detector Active
If something is triggering a detector at the end of the exit procedure, the
system will not set. Depending how your installer has set up the system9,
internal or external sounders may operate. The display shows which zone (or
zones) is active.
To set the system:
1. Enter your access code (or present your tag) to
silence any sounders.
2. Go to the zone shown on the display (see
example) and find out what is triggering the
detector. If possible, remedy the fault.
Zone Open Z03
Zone 03
3. Return to the keypad and set the system again.
If no other detectors are active, the system sets.
4. If other detectors are active, repeat steps 1 to 3.
5. If the system still will not set, call your installer.
9Installer Command 27

2. Everyday Operation
Page 14 497282
Other Problems
The system informs you of problems through alerts. These are warnings
communicated through the keypad display and lamps. If your system is set up
to hide status information after 30 seconds10, enter an access code or present
a tag to activate the keypad display and lamps.
Depending on the nature of the problem, you may need to reset the system or
call an installer to do this for you (see page 17). Your installer may have set
up your system to enable you to override some faults11, in which case you will
be able to set the system while the fault is still present. If the display shows
"Set" underneath the alert message, press yto continue with setting.
If an installer reset is required, the control unit lights the slamp and the
keypad sounds a repeating "beep" to warn you. If the fault disappears, the
lamp goes out but the tone continues until you enter your access code. If the
fault persists and cannot be overridden, the display shows "Call Installer".
A mains power failure is an example of a technical fault that may be resolved
without intervention in the alarm system. A stand-by battery failure is an
example of a technical fault that requires an installer to visit.
If an alert indicates a communications failure (for example, "Plugby Line Fail"),
you may be able to set the system but then it may not be able to report any
alarms to the ARC.
For more information on viewing and acknowledging alerts, see page 19.
10 Installer Command 28
11 Installer Commands 134 to 140

2. Everyday Operation
497282 Page 15
Unsetting the System
WARNING: If you enter your premises and an internal alarm
starts, there may be an intruder.
You can unset the system from a keypad or keyswitch.
When you open an entry door, the system starts an entry timer. There are four
entry timers so that different entrances can use different times. During the
entry time, the keypads give a "galloping" entry tone to warn you that the timer
is running. If you exceed the entry time, an alarm will occur. Your installer will
have ensured that the entry time for each entrance is long enough for you to
enter by the designated entry route, get to the keypad and unset the system.
If an entry door is fitted with a lock switch, the keypad gives a continuous exit
tone when you unlock it and, if you lock it again, the system remains set; it is
only when you open the entry door that the entry timer starts and the keypads
give the entry tone.
General Procedure
To unset the system:
1. Enter through the designated entry door
and go to the keypad.
As you enter the premises, the system
starts the entry timer and the keypads
give the entry tone.
2. Key in an access code (or present a tag).
All set levels are unset.
The entry tone stops and the system
gives a double "beep".
The system is now unset.
Keyswitch Unset
If your system is fitted with a keyswitch, you can use it to unset Level A. With
a three-position keyswitch, switching from Part to Off unsets Level B. You do
not need to enter an access code or present a tag.

2. Everyday Operation
Page 16 497282
Aborting False Alarms
If your system is connected to an ARC and you accidentally cause an alarm,
you normally have at least two minutes before the ARC calls the police. Alarm
Abort12 enables you to cancel a false alarm by entering a valid access code
during this period (which is set by the ARC).
If Alarm Abort is not enabled on your system and you often exceed an entry
timer that is already set to the maximum, ask your installer about Alarm Abort.
12 Installer Command 36

497282 Page 17
3. After an Alarm
Responding to a Fire Alarm
IMPORTANT: The system gives a fire alarm by
sounding a two-tone warning from the keypads and
alarm sounder. The display shows (for example):
Fire Z02 Alarm
9x5x
1. Evacuate the premises.
Do not attempt to unset the alarm.
2. If there is evidence of fire, call the Fire Brigade.
3. Only when the premises are safe, proceed as for
other alarms.
Responding to other Alarms
When your system raises an alarm other than a fire alarm, you must:
• Unset the system as normal to switch off the sounders and strobes.
• Reset the system ready for further use.
The system logs the zone (or zones) that triggered the alarm and displays
alerts on the keypad display. The first zone is shown automatically when you
unset the system. View the others by pressing Yto accept the Next prompt.
For instructions on viewing and acknowledging alerts, see page 19.
Your system may be configured for various types of reset:
• User reset. Enter your access code (or present your tag) again to reset
the system. The system gives a double "beep" to confirm that it has reset.
• Installer reset. If the display shows "Call Installer", contact your alarm
company to arrange a visit.
• Remote reset. If the display shows a reset code, write down the code
and call your ARC. You will be asked to verify your identity, the
circumstances and the code. If no intervention is required from an
installer, you will be given a code to enable you to reset the system.

Page 18 497282
4. Special Functions
Introduction
As well as setting and unsetting the system, you can perform a number of
other functions from the keypad while the system is unset:
All Users Key Description
1 View alerts
2 Omit zones
3 Require user code before installer code
5 Read the log of system events
7 Turn chime on and off
8 Test the sounders and strobe
Access code (or tag)
plus:
9 Test the detectors
1+3 Panic alarm (PA)
4+6 Medical assistance alarm
Dual key alarms
(check if these are
enabled, see page 32) 7+9 Fire alarm
Master User Only Key Description
4 Set up access codes and proximity tags
Access code (not tag)
plus: 6 Set the time and date

Appendix
497282 Page 19
Viewing Alerts
The system records alarms, faults and tampers as alerts. It usually displays
the first alert automatically when you unset the system but you can view alerts
at any time by pressing 1. Viewing an alert acknowledges it. The Alert lamp
() flashes for unacknowledged alerts and glows for acknowledged alerts. If
the condition that caused the alert still exists, the alert message shows
"Active". If the condition no longer exists, the message shows "Inactive".
To view alerts:
1. Key in an access code (or present a tag).
If the
lamp is glowing or flashing, there are
alerts. The system may display the first alert or it
may show how many alerts exist (for example):
3 Problem(s)
Set? ABCD
2. Press 1 to view the alerts.
The display shows the first alert (for example): MAINS Fail
Inactive Next
Here, "Inactive" indicates that the mains power
supply has since been restored.
3. Press
yfor "Next" to view the next alert.
The display shows the second alert (for example): Lid Tamper
Inactive Next
Here, "Inactive" indicates that the tamper switch
has since been closed.
4. Press
yfor "Next" to view the next alert.
The display shows the third alert (for example): Battery Missing
Active Next
Here, "Active" indicates that the battery is still
missing. The slamp will also be lit and there will
be an intermittent audible warning.
If you have viewed all alerts and installer action is
required (for example, to fit a new battery), the
display shows:
Call Installer
9x5x
5. In this case, contact your alarm company.
If you have viewed all alerts and no installer action
is required, the display shows date and time (for
example):
18/04/2005 14:45
9x5x
6. In this case, use the system as normal.

Appendix
Page 20 497282
Omitting Zones
Your system may be programmed so that you can omit individual detectors.
This enables you to ignore alarms coming from faulty detectors in non-critical
positions. Refer to the table on page 32 to see which zones can be omitted in
your system.
To omit a zone:
1. Key in an access code (or present a tag).
2. Press 2.
This display shows: Omit Zone?
3. Press the number of the zone you want to
omit (for example, press 07 to omit zone
7) and then press y.
The sounder gives a double "beep" and
the display shows the zone number
followed by an "o":
Omit Zone 07o
If you try to omit a zone for which this is
not allowed, the display shows an "X"
after the zone number.
Omit Zone 07X
4. Press Xto exit.
Note:To include a zone that was omitted, follow the same procedure.
Pressing ytoggles between omit and include.
Normal Alarm Zones
When you next set the system, a message asks you to confirm that you want
to omit the zone. Press yto set the system with the zone omitted. Omission is
not permanent: when you next unset the system, the control unit reinstates
the zone. You must omit the zone each time you prepare to set the system.
24-hour Zones
When you next set the system, there is no message to confirm the omission.
24-hour zones (for example, protecting a fire door) remain omitted until you
reinstate them from the keypad:
1. Key in an access code (or present a tag).
2. Press 2 followed by the zone number and then y.
3. Press Xto exit.