Copeland Exeter User manual

Tools required
Components included:
Table top assembly with leaf (1)
Lay the table top sub-assembly face
down on a soft level surface. Use a
Philips head screw driver to remove
blocks under the table top assembly by
detaching all the flat head screws from
the shipping blocks (Figure 1).
Remove any packing material
underneath the table.
Step 1: Remove the shipping blocks
Philips head screw driver
Hardware included:
¼” - 20 x 50mm hex bolts (4)
1
Figure 1. Remove the shipping blocks from
Table top
assembly
4mm Allen wrench (1) Leg base assembly (1)
Exeter two-leaf extension tables:
Flat head screws
Shipping
block
Shipping
block
the table top sub-assembly
Remove the
shipping blocks
Flat head screws
42" W x 72/96/112" L x 30" H
Instructions for Exeter Two-leaf
Extension Table
surface and identify
the listed items.
Unpack the table
onto a soft level

Tools required
Install the leg base to the table top assembly by
aligning and inserting each tenon on the leg base into
the cutout on the table top assembly.Then slide a ¼” –
20 x50mm hex bolt into each hole and tighten with the
provided Allen wrench to secure the leg base
assembly to the table top assembly (Figure 2).
Step 2: Install the table leg sub-assembly
Allen wrench
Figure 2.
Install the leg assembly to
2
Table top
assembly
the table top assembly
Lockup handle
¼” – 20 x
50mm hex bolt
Leg Base
Cutout
Attention
After the table is fully assembled, DO NOT try to pick up the table from the ends –
especially if the table is fully extended. Should the table need to be relocated, close the
table and carefully lift the table in the middle area where the two tops meet.

To unfold the leaves, unlock the table and open the table top (Figure 4). Before unfolding the
leaves, make sure to move the two leaves all the way towards the left/right tops.
Figure 4. Unfold the leaves
3
When
in use How to unfold the table leaves
Lockup handle
How to use the Slide Lock to lock and unlock the table top
hen
in use
W
To lock the top, push down the small
black handle in the middle of the slide
arm. To unlock the top, simply push the
handle up on both sides. Lock-up
handle located in the middle of the slide
arm (Figure 3). If you prefer to use
Table Lock to operate the table top,
please keep this Slide Lock unlocked at
all times after initial setup of the table.
Figure 3. Lockup handle location

Care Instructions
To care for and preserve the finish on your new Copeland Furniture piece, please keep the following
recommendations in mind.
While our furniture has been finished with a durable top coat, the surface may be sensitive to
dents and abrasions during the first 30 days in your home.
Treat the surface finish gently so it does not dent or chip. Tape or stickers should not be put on
the finish.
For general care use a soft cloth to dust the furniture.
Use damp cloth with a mild soap to clean-up spills or dirt. Dry the surface thoroughly.
Please do not use any polishes, waxes or solvents to clean the surface of the furniture. This holds
true for new Copeland Furniture pieces as well as items you may already have in your home.
Please do not place any candles directly on the surface of your furniture. The perfumes and dyes
in the candles may penetrate the finish.
Beds must be disassembled before moving to avoid damage. Never attempt to move the bed
while it is assembled.
If you have any questions or difficulties, please call us at the number below between the hours of 8:00 am and 4:30 pm eastern time.
156 Industrial Drive, Bradford, VT 05033 Tel: [phone] Fax: [phone] www.copelandfurniture.com

How to Operate Extension Table Lock Mechanism
Tools required None
One leaf extension tables usually have two locking locations (Figure 1). The inner position is for
locking the table when the leaf is unfolded (Figure 1-2). The outer position is for locking the table
when the leaf is folded (Figure 1-1). Two leaf extension tables have three locking locations. Similar
to the one leaf table, the inner locking location is for when leaf is folded, the middle locking
position is for when one leaf is open, the outer locking location is for when two leafs are open.
Figure 1-1. Outer locking position when leaf folded
To release the lock, simply rotate the
long handle (on the underside of the
table) so that the short lock pin
disengages from the friction plate
(Figure 2-1).
Figure 1-2. Inner locking position when leaf unfolded
Locking locations
How to lock/unlock the extension
table
To lock the table, rotate the long handle
on the lock mechanism till the short
lock pin engages with the friction plate
(Figure 2-2).
Long handle
Short lock
pin
Friction
plate
Long
handle
Friction
plate
Short
lock pin
Outer locking
locations Inner locking
locations
Figure 2-1.
Unlock the table
Figure 2-2.
Lock the table