Copeland Catalina CF1CAL12 User manual

Catalina Bed
assembly instructions
Notice: Beds must be disassembled before moving to avoid damage. Never attempt to move the bed while it is assembled.
Failure to do so would void the warranty.
Your Catalina bed is delivered in four boxes. Unpack the bed parts onto a soft, level surface in the space where the bed is to be
used. Lay out the headboard, side rails and footboard in their approximate locations.
Tools required for assembly - Straight and right angle wrenches (included) and Phillips Head Screw Driver.
www.copelandfurniture.com
Footboard Assembly x1
Headboard Assembly x1
Platform Assembly x6
Side Rail Assembly x2
Hardware List
Threaded Rods (8)
Nuts (8)
Washers (8)
Straight Wrench
Right Angle Wrench Packaged By
#10 x 1 1/2" Screws (12)
#8 x 1 3/4" Screws (3)

Catalina Bed - assembly instructions
Step 1
Install all threaded rods into the threaded inserts (pre installed in the headboard and footboard)
and hand tighten as far as possible.
Step 2
Slide a side rail onto the headboard using the dowel in the end of the rail and the threaded rod as a guide. Place a washer and
hex nut over each rod. Fully tighten with the provided straight wrench.
Step 3
 Repeat step three on the second pocket (located beneath each side rail) using the right angle wrench.
 Repeat two and three at the other side of the headboard and both sides of the footboard.
www.copelandfurniture.com
Threaded Insert
(pre-installed)
Threaded Rod x8
Washer and Hex Nut x8
Attachment Locations
x2
x2
x2
x2
Second Pocket Location

Catalina Bed - assembly instructions
Step 4
Step 5
Step 6
www.copelandfurniture.com
Center Support Legs x3 #8 1 3/4” Flat Head Screws x3
#10 1 1/2” Washer Head Screws x12
Adjustable Foot
 Platforms assemblies are to be
positioned on the side rails as the
illustration shows.
 Begin with one platform assembly
closest to headboard and proceed to
step 5
 Starting with the second platform assembly from the
headboard, position 1 center support leg under the hardwood
support brace as shown in the diagram .
 Retract the adjustable foot slightly so that it only makes
contact with the floor when weight is applied to the fully
assembled bed.
 Using a 1 3/4” screw, attach the support block to the center of
the platform assembly making sure the support brace is in full
contact with the shoulder on the support block.
 Repeat process for the two middle platform assemblies.
Hardwood Support Brace
Side View of Assembled Side Rail, Platforms and Center Support Blocks
Use the 1 1/2” screws to fasten each
platform assembly to the cleats on both
side rails.

Catalina Bed Care Instructions
Special Care Instructions for Cherry Furniture - Please read the following if you have purchased
a Copeland product in cherry.
Furniture that has been crafted from cherry wood becomes darker with age. The change in color, from a
reddish tan to a reddish brown, is most noticeable during the first six months of ownership. It is important to
understand that exposure to light accelerates the natural oxidization process. An object left on a cherry
wood surface for an extended period of time may retard the aging process in a limited area.
Simply remove the object and, over time, the surface will attain a uniform reddish brown color.
Important: Please Note:
Beds must be disassembled before moving to avoid damage. Never attempt to move the bed while it is assembled.
To care for and preserve the finish on your new Copeland Furniture piece, please keep
the following recommendations in mind.
 While our furniture has been finished with a durable top coat, the surface may be sensitive to dents and
abrasions during the first 30 days in your home.
 Treat the surface finish gently so it does not dent or chip. Tape or stickers should not be put on the finish.
 For general care use a soft cloth to dust the furniture.
 Use damp cloth with a mild soap to clean-up spills or dirt. Dry the surface thoroughly.
 Please do not use any polishes, waxes or solvents to clean the surface of the furniture. This holds true for new
Copeland Furniture pieces as well as items you may already have in your home.
 Please do not place any candles directly on the surface of your furniture. The perfumes and dyes in the candles
may penetrate the finish.
If you have any questions or difficulties, please call us at the number below between the hours of 8:00 am and 4:30 pm eastern time.
156 Industrial Drive, Bradford, VT 05033 Tel: [phone] Fax: [phone] www.copelandfurniture.com