Costco 1487755 User manual

Page: 1 of 5
(For Indoor Use Only)
Frequency Bands: 433.92 +/-0.5MHz
Maximum output power: 1.0mW
Fig. B - Tree and Light Assembly
3.6 m / 12 ft EZ Connect™ Pre-lit Aspen Radiant Micro LED® Tree
ITM. / ART. 1487755, 53694, 313911
IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY
This tree comes with EZ Connect™ and Simple Shape™ technology, allowing you to set up and light your tree in less than 10
minutes! Carefully follow the instructions below on how to quickly and easily set up your new tree.
1. Choose an appropriate location near a wall outlet.
2. Assemble the tree stand on a level surface. (See Fig. A)
TREE ASSEMBLY INSTRUCTIONS
For assistance with assembly, parts and customer service, call (US & Canada only): 1-844-907-6657 (English, Spanish, French)
Mon-Fri 10am -7pm EST, email: [email protected], or visit www.polygroupstore.com.
Please note if you are calling outside of USA & Canada, international toll fees may apply.
Customer Service Hotline Hours: 8am-5pm, Mon-Fri, MST.
NEED HELP?
DO NOT RETURN TO STORE. PLEASE VISIT US AT:
www.polygroupstore.com OR 1-844-907-6657
Eye Bolt
Click
Eye Bolt
1. Pull apart the legs of the stand so that
they are snapped into an x-shape, place the
tree stand on a level surface.
2. When inserting the bottom section of the tree
into the assembled stand, insert and turn the
eyebolts into the stand and tighten until the
tree pole is firmly secured.
To close the stand, remove the eyebolts, press
the metal button and fold the legs together.
Fig. A - Tree Stand Assembly
SP,ICE(K58S290200E2)
UK(K58S290200E2)
AU(K58S290200E2)
US, CAN, MX, TW
(TS-48W29V)
Plug Adapter
Into Wall
Outlet
Light Controller
Foot Pedal
On/Off Switch
Section 1
Section 2
Section 3
Section 4
Tree Top
Align both arrows
in a straight line
before sliding
down to connect
Open the
cap cover
Do not tamper with
internal parts

1. Unplug adapter from the wall outlet. Then remove all ornaments and decorations.
2. Disassemble the tree from the top to the bottom. Gently lift the center pole straight up to remove from the section below , and
fold all branches toward the pole. Continue until the lowest tree section is removed from the tree stand.
3. Close the protective caps on the poles to avoid damaging the internal parts. (See Fig. D)
4. Carefully place all tree sections into the shipping box and tape (not included) it shut.
5. Store your tree in a cool, dry place away from sunlight. Exposure to excessive heat or
humidity may damage your tree.
STORAGE INSTRUCTIONS
TROUBLESHOOTING TIPS
3. Each tree section is numbered with a sticker. Please identify all sections before assembling.
4. Assemble the tree from the bottom to the top (See Fig. B). Remove protection cap, and insert the center pole into the stand.
Then slot together the remaining poles securely until the tree top is installed. Be sure that all cords are free from branch hinges.
5. Plug the adapter into the wall outlet (See Fig. B). Your entire tree should now be lit.
6. This is a Simple Shape™ tree and no shaping is required. Just slightly upsweep all tips (See Fig. C) and shift branches to fill in any
gaps for a fuller, uniform look. Your Christmas tree is now ready to be decorated.
Top view Side view
Fig. C
Page: 2 of 5
If Tree Does Not Illuminate / Some Bulbs Do Not Light or Flicker
1.
Check to make sure that all connectors are properly connected and the adapter is plugged firmly into the wall outlet.
2. Turn the poles gently to ensure pole-to-pole connection is secured.
3. Try stepping on the On/Off switch foot pedal.
Loose Hinge Pin
1. Place the branch into the slot of the bracket.
2. Insert a new hinge pin (included) through the hole and secure with
a retainer washer (included). (See Fig. E)
TROUBLESHOOTING TIPS
Fig. E
This tree includes hinge pins/washers.
If extra parts are needed, please contact our customer service center.
SPARE PARTSSPARE PARTS
Simply press the selector button to select from the following light functions:
1. CLEAR STEADY 2. CLEAR FADING 3. MULTI-COLOR STEADY
4. MULTI-COLOR FADING 5. CLEAR/MULTI-COLOR FADING
DUAL COLOR LIGHT CONTROLLER INSTRUCTIONS Selector
Button
Remote Control Light
Controller
Insulation Tab
REMOTE CONTROL INSTRUCTIONS
1. Remove the insulation tab of the remote control.
2. Press either selector button and wait for a second to enjoy light effects in the following sequence
(see DUAL COLOR LIGHT CONTROLLER & REMOTE CONTROL).
There are 13 brightness levels. Simply press the controller buttons
to increase or decrease the brightness to your liking.
Fig. D

Page: 3 of 5
2. Replace the used battery with a new CR2032 button cell battery (not included). Ensure the batteries are installed correctly with
regard to polarity (+ and -).
3. Retighten the screw to close and secure the battery cover.
Cover
Battery
CR2032
BATTERY REPLACEMENT
1. Loosen the screw of the battery cover with a screwdriver (not included).
AUSTRALIA: Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to
a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are
also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount
to a major failure.
Hereby, Polygroup declares that the Christmas Tree is in compliance with RED 2014/53/EU. The full test of the EU declaration of
conformity is available at the following internet address:
https://support.polygroupstore.com/hc/en-us/articles/360037856794-Tree-Instructions-Manual-Search-by-Model-Number
DISPOSAL OF USED BATTERIES
Battery may contain hazardous substances which could endanger the environment and human health.
This symbol marked on the battery and/ or packaging indicates that used battery shall not be treated as
municipal waste. Batteries should be disposed of at an appropriate collection point for recycling. By ensuring
the used batteries are disposed of correctly, you will help preventing potential negative consequences for the
environment and human health. The recycling of materials will help to conserve natural resources. For more
information about recycling of used batteries, please contact your local municipality waste disposal service.
1. Use only the power adapter supplied with this product. Using a different adapter can damage the lights and will cause fire or
electrical shock hazards.
2. This product contains a CR2032 button cell battery. If swallowed, it could cause severe
injury or death in just 2 hours due to chemical burns and potential perforation of the
oesophagus – seek medical attention immediately.
3. Small parts, keep batteries out of reach of children.
4. If you suspect your child has swallowed or inserted a button cell battery, immediately seek urgent medical assistance.
5. Make sure the battery compartment is correctly secured (e.g. the screw or other mechanical fastener is tightened), and do not use
if the compartment is not secured.
6. Dispose of used button cell batteries immediately and safely. Flat batteries can still be dangerous.
7. Inform others about the risk associated with button cell batteries and how to keep their children safe.
8. Do not expose the lights to moisture.
9. Remove the batteries when the controllers are left unused and are not expected to be used for an extended period of time, or
when depleted.
10. Dispose of the used battery properly as per the directions on batteries, and local laws and regulations regarding the disposal of
hazardous waste.
11. Clean the battery contact surfaces prior to battery installation.
12. Do not dispose of batteries in fire – batteries may leak or rupture.
13. Use only CR2032 button cell battery for remote controller.
14. This product is powered by a lithium battery. Due to their small size, lithium batteries can easily be swallowed by children.
Ingestion of such batteries has been known to cause death.
15. For decoration purposes only. The light source is not intended for use in other applications.
WARNING
Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities.
Contact your local government for information regarding the collection systems available. If electrical
appliances are disposed of in landfills or dumps, hazardous substances can leak into the groundwater and
get into the food chain, damaging your health and well-being.

Page: 4 of 5
MADE IN CHINA / FABRIQUÉ EN CHINE / HECHO EN CHINA
Distributed by:
Costco Wholesale Corporation
P.O. Box 34535
Seattle, WA 98124-1535
USA
1-800-774-2678
www.costco.com
Costco Wholesale Iceland ehf.
Kauptún 3-7, 210 Gardabaer
Iceland
www.costco.is
Costco France
1 avenue de Bréhat
91140 Villebon-sur-Yvette
France
01 80 45 01 10
www.costco.fr
Costco Wholesale Japan Ltd.
3-1-4 Ikegami-Shincho
Kawasaki-ku, Kawasaki-shi,
Kanagawa 210-0832 Japan
0570-032600
www.costco.co.jp
Costco Wholesale Korea, Ltd.
40, Iljik-ro
Gwangmyeong-si
Gyeonggi-do, 14347, Korea
1899-9900
www.costco.co.kr
Costco Wholesale Spain S.L.U.
Polígono Empresarial Los Gavilanes
C/ Agustín de Betancourt, 17
28906 Getafe (Madrid) España
NIF: B86509460
900 111 155
www.costco.es
Costco Wholesale Canada Ltd.*
415 W. Hunt Club Road
Ottawa, Ontario
K2E 1C5, Canada
1-800-463-3783
www.costco.ca
* faisant affaire au Québec sous
le nom les Entrepôts Costco
Importado por:
Importadora Primex S.A. de C.V.
Blvd. Magnocentro No. 4
San Fernando La Herradura
Huixquilucan, Estado de México
C.P. 52765
RFC: IPR-930907-S70
(55)-5246-5500
www.costco.com.mx
Costco Wholesale Australia Pty Ltd
17-21 Parramatta Road
Lidcombe NSW 2141
Australia
www.costco.com.au
Costco Wholesale UK Ltd /
Costco Online UK Ltd
Hartspring Lane
Watford, Herts
WD25 8JS
United Kingdom
01923 213113
www.costco.co.uk
Costco Wholesale New Zealand Limited
2 Gunton Drive
Westgate
Auckland 0814
New Zealand
Costco (China) Investment Co., Ltd.
Room 1003, Block 2, 2388 Xiupu Road,
Pudong New Area, Shanghai
China 201315
[phone]

Page: 5 of 5
CUSTOMER SERVICE FOR CHRISTMAS TREES
For any questions, assistance, or missing parts, DO NOT RETURN YOUR TREE TO PLACE OF PURCHASE. Please contact us
via: call (US & Canada only) 1-844-907-6657 (English, Spanish, French) Mon-Fri 10am -7pm EST, email:
[e-mail], or visit www.polygroupstore.com.
TREE ID# IS LOCATED ON END PANEL OF BOX. TREE ID# IS REQUIRED WHEN REQUESTING REPLACEMENT PARTS.
Customer Name:
Address (No P.O. boxes):
City & State:
Zip Code:
Day Phone:
Date Purchased:
Tree ID#:
Tree UPC#:
Store Purchased:
Specify Problem: