Craftsman Edger 536.772360 User manual

Print Vendor
Instructions
How to use this file
Operator’s Manuals
Paper Size: • 11x17
• Body & Cover - 50 lbs brilliant white offset or equivalent
Press: • Body & Cover - 1 color, 2-sided
Bindery: • Saddle stitch, face trim *if too thick for saddle stitch, tape bind
Covers: • FRONT COVER is present at the beginning of the file.
• BACK COVER is at the back of the file
• The part number for this manual (typically a 172_____ number) is
located on the front cover.
• This file may contain several manual which differ only by their covers.
See the part number at the bottom of the cover page. .
Body: • The body for all manuals is identical regardless of the cover.
• Odd number pages are always right hand pages, even number pages
are always left hand pages.
General: • This instruction sheet is NOT part of the manual and must not be
printed.
• Pages labeled “THIS PAGE INTENSIONALLY BLANK” are placement
pages and should NOT be printed.

THIS PAGE INTENTIONALLY BLANK
(FOR PLACEMENT ONLY - DO NOT PRINT)

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
www.sears.com/craftsman
Operator’s Manual
Edger
500 Series Engine
9 Inch Blade
Model 536.772360
Orilladora
500 Series Engine
de 9 pulgada lámina
Modelo 536.772360
CAUTION: Before using this
product, read this manual and
follow all of its Safety Rules and
Operating Instructions.
PRECAUCIÓN: Antes de usar este
producto, lea este manual y siga todas
las reglas de seguridad e instrucciones
de operación.
Manual del usario
(página 43)
1741876 TP 899--4502--02-- E G -- C

2
Table of Contents
Craftsman Edger Warranty 2.........
Operator Safety 3...................
Symbols And Warnings 3............
Operator Safety Rules 6...................
Assembly 8.........................
Parts Packed Separately In Carton 8........
RemovalFromTheCarton 8...............
How To Raise The Handle 9................
Features 10..........................
Operation 11.........................
Before Starting The Engine 11...............
How To Start The Engine 13.................
How To Stop 14...........................
How To Use The Depth Control Lever 14......
Edging Tips 18............................
Maintenance 19......................
Maintenance Chart 19.....................
Recommended Maintenance 19.............
How To Remove The Belt 20................
How To Replace The Blade 21...............
Engine Maintenance 22.....................
Storage 25................................
Troubleshooting 26..................
Product Specifications 27............
Power Ratings 27..........................
Illustrated Parts List 30...............
Edger 30.................................
Engine 34................................
Craftsman Edger Warranty
TWO YEAR FULL WARRANTY ON CRAFTSMAN EDGER
When assembled, operated and maintained according to all supplied instructions, if this
Craftsman Edger fails due to a defect in material or workmanship within two years from the
date of purchase, return it to any Sears store, Sears Parts & Repair Center, or other
Craftsman outlet in the United States for free repair (or replacement if repair proves
impossible). This warranty does not include Edger spark plugs, blades or belts, which are
expendable parts that can wear out from normal use in less than two years.
This warranty applies for only 90 days if this Edger is ever used for commercial or rental
purposes.
This warranty gives you specific rights, and you may also have other rights which vary from
statetostate.
Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, IL 60179

3
Symbols And Warnings
This manual contains safety
information to make you aware of the hazards and
risks associated with edgers, and how to avoid them.
The edger is designed and intended only for lawn
care edging and trimming, and should not be used for
any other purpose. It is important that you read and
understand these instructions, and that anyone who
operates this equipment also read and understand
these instructions.
The safety alert symbol is used to identify safety
information about hazards that can result in personal
injury. A signal word (DANGER, WARNING, or
CAUTION) is used with the alert symbol to indicate the
likelihood and the potential severity of injury. In addition,
a hazard symbol may be used to represent the type of
hazard.
DANGER indicates a hazard which, if not
avoided, will result in death or serious
injury.
WARNING indicates a hazard which, if not
avoided, could result in death or serious
injury.
CAUTION indicates a hazard which, if not
avoided, might result in minor or moderate
injury.
CAUTION,when used without the alert
symbol, indicates a situation that could result
in damage to the product.
The engine exhaust from this product contains
chemicals known to the State of California to cause
cancer, birth defects, or other reproductive harm.
WARNING
Explosion
Toxic Fumes
Moving Parts
Shock
Hot Surface
Kickback
Fire
Fuel Shutoff
Read
Manual
Choke
Oil
Fuel
On Off
Stop
Wear Eye
Protection Slow
Fast
SYMBOLS ASSOCIATED
WITH THIS PRODUCT:
Thrown
Objects

4
Gasoline and its vapors are
extremely flammable and explosive.
Fire or explosion can cause severe
burns or death.
When Adding Fuel
xStop the engine. Let engine cool at least 2
minutes before removing the gas cap.
xFill fuel tank outdoors or in well-ventilated
area.
xDo not overfill fuel tank. Fill tank to
approximately 1-1/2 inches below top of neck
to allow for fuel expansion.
xKeep gasoline away from sparks, open
flames, pilot lights, heat, and other ignition
sources.
xCheck fuel lines, tank, cap, and fittings
frequently for cracks or leaks. Replace if
necessary.
xIf fuel spills, wait until it evaporates before
starting engine.
When Starting Engine
xMake sure spark plug, muffler, fuel cap and air
cleaner are in place.
xDo not crank engine with spark plug removed.
xIf engine floods, set choke to OPEN/RUN
position, place throttle in FAST and crank until
engine starts.
When Operating Equipment
xDo not tip engine or equipment at angle which
causes gasoline to spill.
xDo not choke carburetor to stop the engine.
Move the throttle control to the stop position to
stop the engine.
When Transporting Equipment
xTransport with fuel tank EMPTY or with fuel
shut-off valve OFF.
When Storing Gasoline Or Equipment With
Fuel In Tank
xStore away from furnaces, stoves, water
heaters or other appliances that have pilot
light or other ignition source because they can
ignite gasoline vapors.
WARNING
Starting engine creates sparking.
Sparking can ignite nearby flammable
gases.
Explosion and fire could result.
xIf there is natural or LP gas leakage in area, do
not start engine.
xDo not use pressurized starting fluids because
vapors are flammable.
WARNING
Engines give off carbon monoxide, an
odorless, colorless, poison gas.
Breathing carbon monoxide can
cause nausea, fainting or death.
WARNING
xStart and run engine outdoors.
xDo not start or run engine in enclosed area,
even if doors or windows are open.
Rapid retraction of starter cord (kickback)
will pull hand and arm toward engine
faster than you can let go.
Broken bones, fractures, bruises or
sprains could result.
WARNING
xBefore starting the engine, make sure to raise
the blade.
xWhen starting engine, pull the starter cord
slowly until resistance is felt, then pull rapidly.
xRemove all external equipment/engine loads
before starting engine.
xDirect-coupled equipment components such as,
but not limited to, blades, impellers, pulleys,
sprockets, etc., must be securely attached.

5
Rotating parts can contact or entangle
hands, feet, hair, clothing, or
accessories.
Traumatic amputation or severe
laceration can result.
WARNING
xOperate equipment with guards in place.
xKeep hands and feet away from rotating parts.
xTie up long hair and remove jewelry.
xDo not wear loose-fitting clothing, dangling
drawstrings or items that could become
caught.
xBefore unclogging the blade or making
repairs, stop the engine by moving the throttle
control to the stop position. Disconnect the
wire from the spark plug.
xBefore you adjust the wheels or change the
position of the blade, stop the engine by
moving the throttle control to the stop position.
xNever leave the unit unattended while the
engine is running.
xKeep bystanders away from machine.
Running engines produce heat.
Engine parts, especially muffler,
become extremely hot.
Severe thermal burns can occur on
contact.
Combustible debris, such as leaves,
grass, brush, etc. can catch fire.
WARNING
xAllow muffler, engine cylinder and fins to cool
before touching.
xRemove accumulated debris from muffler area
and cylinder area.
xInstall and maintain in working order a spark
arrester before using equipment on
forest-covered, grass-covered, brush-covered
unimproved land. The state of California
requires this (Section 4442 of the California
Public Resources Code). Other states may
have similar laws. Federal laws apply on
federal land.
Before performing adjustments or repairs:
xDisconnect the spark plug wire and keep it
away from the spark plug.
xUse only correct tools.
xDo not tamper with governor spring, links or
other parts to increase engine speed.
When testing for spark:
xUse approved spark plug tester.
xDo not check for spark with spark plug
removed.
Unintentional sparking can result in
fire or electric shock.
Unintentional start-up can result in
entanglement, traumatic amputation,
or laceration.
WARNING
Thrown debris can result in foreign
objects being thrown into the eyes,
which can cause severe eye damage.
WARNING
xAlways wear safety glasses or eye shields while
you assemble, operate or perform maintenance
to the unit.
xNever sharpen the blade, always replace.
Sharpening the blade will cause the blade
to shatter.
xBefore doing an adjustment, maintenance
or repair, disconnect the spark plug wire
and keep it away from the spark plug.
WARNING
Sharpening can damage the blade
and cause it to break.
Unintentional start-up can result in
entanglement, traumatic amputation,
or laceration.

6
Operator Safety Rules
Before Use
xREAD AND FOLLOW ALL INSTRUCTIONS --
Read the instruction manual carefully. Be
thoroughly familiar with the controls and the proper
use of the Edger. Know how to stop the Edger and
disengage the controls quickly.
xDRESS PROPERLY -- Wear safety glasses or eye
shields to protect your eyes from thrown objects.
Do not wear loose clothing or jewelry. They can be
caught in moving parts. Use of sturdy gloves and
safety footwear is recommended. Wear footwear
that will improve footing on slippery surfaces. Do
not operate product when barefoot or wearing open
sandals. Always wear safety footwear, and pants or
slacks that cover your legs.
xSTAY ALERT -- Watch what you are doing -- use
common sense. Do not operate product when
fatigued or under the influence of alcohol or drugs.
xKEEP OPERATING AREA CLEAR -- Keep the
area of operation clear of all persons, particularly
small children and pets.
xINSPECT AREA -- Thoroughly inspect the area
where the Edger is to be used and remove all
foreign objects. Objects struck by the cutting
member can cause severe injuries to persons.
Fuel Safety
xAllow muffler and engine areas to cool before
touching.
xHandle fuel with care; it is highly flammable.
xUse an approved container.
xTurn engine OFF and let engine cool at least 2
minutes before removing the gas cap.
xCheck fuel supply before each use. Do not overfill
fuel tank. To allow for fuel expansion, fill fuel tank
to approximately 1-1/2 inches below top of fuel
tank neck. Replace gasoline cap securely.
xFill fuel tank outdoors with extreme care. Never fill
fuel tank indoors or near appliances with pilot
lights, heaters, or other ignition sources. Replace
fuel tank cap securely and wipe up spilled fuel.
xNever remove the fuel tank cap or add fuel to a
running or hot engine.
xNever store fuel or Edger with fuel in the tank
inside a building where fumes may reach an open
flame or other ignition source.
Operating Safety
xRead and follow all instructions in this manual
carefully.
xNever operate the product without guards, plates
or other protective devices in place. Operate
product from position where guards block the line
of sight to the cutting member.
xNever allow children to operate the Edger. Keep
them away while it is operating. Never allow adults
to operate the Edger without proper instruction.
xDo not operate this machine if you are taking drugs
or other medication which can cause drowsiness or
affect your ability to operate this machine.
xDo not use this machine if you are mentally or
physically unable to operate it safely.
xTo protect your eyes from foreign object that may
be thrown from the Edger, always wear safety
glasses or eye shields during operation or while
performing an adjustment or repair.
xDo not put hands or feet near or under rotating
parts including cutting area. Keep both hands on
handles when blade is rotating. Cutting member
coasts after turn off.
xDo not attempt to remove cut material nor hold
material to be cut when engine is running or when
cutting member is moving.
xExercise extreme caution when operating on or
crossing drives, walks, or roads. Stay alert for
hidden hazards or traffic.
xExercise caution to avoid slipping or falling. Don’t
overreach or stand on unstable support. Keep good
footing and balance at all times.
xUse only for edging or trimming the type of growth
as described in the operating instructions. Do not
abuse the product. Do not use the product on
graveled surfaces.
xNever operate the Edger at high transport speeds
on slippery surfaces. Do not use product in rain or
wet locations. Look behind and use care when
backing.
xStay alert for uneven sidewalks, holes in terrain or
other similar conditions when using product.
Always push slowly over rough ground.
xNever direct discharge of material toward
bystanders nor allow anyone near the area of
operation. Use care in directing discharge to avoid
glass enclosures, automobiles, and similar objects.
xKeep children and pets away while operating.
xNever operate the Edger without good visibility or
light.
xDo not run the engine indoors. The exhaust fumes
are dangerous, containing CARBON MONOXIDE,
an ODORLESS and DEADLY gas.
xMake sure that spark plug, muffler, fuel cap and air
cleaner are in place when operating.
xMake sure spark plug is disconnected when
clearing jammed material from cutting member. Do
not crank engine with spark plug remove.

7
xIf fuel spills, wait until it evaporates before starting
engine.
xTake all possible precautions when leaving the
Edger unattended or during transport. Stop the
engine.
xDo not overload the Edger capacity by attempting
to till too deep at too fast a rate.
Maintenance / Repair / Adjustments
Safety / Storage
xFollow maintenance instructions given in Manual.
xDo not change the engine governor settings or
overspeed the engine.
xTo reduce the risk of fire, do not allow excessive
grass, leaves, or grease to accumulate on the
product.
xAfter striking a foreign object, stop the engine.
Remove the wire from the spark plug, and keep the
wire away from the plug to prevent accidental
starting. Thoroughly inspect the Edger for any
damage. Repair the damage before restarting and
operating.
xDo not operate product with a damaged or
excessively worn cutting member.
xHave repairs made by a qualified dealer or
repairman. See that only identical replacement
parts are used.
xIf Edger should start to vibrate abnormally, stop
engine and check immediately for the cause.
Vibration is generally a warning of trouble.
xStop the engine whenever you leave the operating
position. Also, disconnect the spark plug wire
before unclogging the blade and when making any
repairs, adjustments, or inspections.
xWhen cleaning, repairing, or inspecting, shut off the
engine and make certain all moving parts have
stopped. Remove the wire from the spark plug, and
keep the wire away from the plug to prevent
accidental starting.
xNever attempt to make any adjustments while the
engine is running.
xWhen not in use, disconnect spark plug lead and
store product indoors in a dry place locked or
otherwise inaccessible to children.
xSAVE THESE INSTRUCTIONS

8
Assembly
Parts Packed Separately In Carton
1--Owner’s Manual (not shown)
1--Container Of Oil
2--Hair Pin
1--Control Rod 1 -- Container of Oil 2--HairPin
1 -- Control Rod
Thrown debris can result in foreign
objects being thrown into the eyes,
which can cause severe eye damage.
WARNING
Always wear safety glasses or eye shields while
you assemble, operate or do maintenance to
the unit.
Figure 1 shows the product completely assembled.
References to the right or left side are from the
viewpoint of the operator’s position behind the unit.
Removal From The Carton
1 Remove the bottle of oil and parts bag from the
carton.
2 Cut down all four corners of the carton.
3 Remove the packing material positioned around
the front and rear of the unit. Leave the packing
material on the bottom of the unit until the control
rod is assembled. This will keep the front wheel in
a stable position.
4 Lift the machine out of the carton and place on a
hard level surface.
Figure 1: Product Completely Assembled

9
How To Raise The Handle
1 Loosen the knobs (A) and raise the upper handle
(B) to the upright position. See Figure 2.
2 Tighten the knobs. Make sure the knobs are to the
outside of the handles as shown in Figure 2.
B
A
Figure 2: Handle Assembly
3 Insert the end of the control rod (C), from RIGHT
to LEFT, through the hole in the front wheel arm
(D). Attach with the hair pin (E) found in the parts
bag. See Figure 3.
E
D
Figure 3: Lower Control Rod Assembly
C
4 Push down on the handle to tilt the unit back.
5 Insert the other end of the control rod, from RIGHT
to LEFT, through the hole in the depth control lever
(F) and fasten with the hair pin. See Figure 4.
F
E
C
Figure 4: Upper Control Rod Assembly
6 Move the depth control lever forward to the
STARTING and TRANSPORT position.
7 Remove any packing material from the bottom of
the unit.
8 Twist the starter rope (G) through the rope guide
(H). See Figure 5.
Figure 5: Starter Rope
G
H
nAssembly Checklist
For the best performance and satisfaction from this
quality product, please review the following checklist
before you operate the product:
nAll assembly instructions have been completed.
nCheck carton. Make sure no loose parts remain
in the carton.
nAll fasteners have been properly tightened.
nAdd engine oil to the engine. See “Before
Starting The Engine” in the Operation Section.

10
Features
AEngine Stop Lever -- Must be engaged to
allow the engine to start and run. Release
to stop the engine.
BStarter Rope Handle -- The engine is
equipped with an easy pull recoil starter.
CBlade Depth Lever -- Controls depth of cut.
DControl Rod
EAir Filter
FFuel Tank
GPrimer Button -- Injects fuel directly into the
carburetor for cold starts.
HDipstick
IBlade Guard -- Use to prevent stones and
debris from being thrown at the operator.
JBlade
KBlade Guide
LQuill Assembly
MOil Drain Plug (located on bottom of
engine)
NEngine Model Number
OProduct Model Number
PAdjustable Front Wheel -- Front wheel can
be lowered for edging along curbs.
QAdjustable Rear Wheel -- Right rear wheel
is adjustable to level the Edger when
edging along curbs.
RIndex Lever -- Use to set the angle of the
blade.
A
B
C
D
I
J
K
Q
H
E
F
G
P
M
M
Bottom View
L
N
O
Side View
R

11
Operation
Read “Operator Safety Rules” section prior to using
this product.
Before Starting The Engine
This engine was shipped from the factory without
oil. If you start the engine without oil, the engine
will be damaged beyond repair and will not be
covered under warranty.
CAUTION
Eye Protection
Always wear safety glasses. If you wear eye glasses,
put a Wide Vision Safety Mask over your eye glasses.
Thrown debris can result in foreign
objects being thrown into the eyes,
which can cause severe eye damage.
WARNING
xAlways wear safety glasses or eye shields while
you assemble, operate or do maintenance to
the unit.
Oil Capacity
The engine holds approximately 20 ounces (0.6 liter)
of oil.
Oil Recommendation
Choose a viscosity from the following chart.
SAE 30 40ºF and higher (5ºC and higher)
is good for all purpose use above 40ºF, use below
40ºF will cause hard starting.
10W-30 0to100ºF (--18 to 38ºC)
is better for varying temperature conditions. This
grade of oil improves cold weather starting, but may
increase oil consumption at 80ºF(27ºC) or higher.
Check oil level frequently at higher temperatures.
Synthetic 5W-30 --20 to 120ºF (--30 to 40ºC)
provides the best protection at all temperatures as
well as improved starting with less oil consumption.
5W-30 40ºF and below (5ºC and below)
is recommended for winter use, and works best in
cold conditions.
Check Oil Level
xBefore you start the engine, check the oil level.
xMake sure the engine is level. Remove the dipstick
(A) from the engine oil fill (B).
xMake sure that the oil level is at the FULL mark
shown on the dipstick (see Figure 6).
Check oil level daily, or after every eight (8) hours.
Add Oil
1 Make sure the engine is level.
2 Clean the engine oil fill area of debris.
3 Remove the dipstick from the engine oil fill. Wipe
the dipstick with a clean cloth.
4 Install and tighten the dipstick. Remove and check
the oil level.
5 To add oil, pour the oil slowly into the engine oil fill.
6 Fill to the FULL mark shown on the dipstick (see
Figure 6). Pour slowly. Do not overfill.
A
Figure 6: Oil Fill
B

12
Gasoline Requirements
All gasoline is not the same. If a starting or
performance problem is encountered after new
gasoline has been used, try another service station or
change brands.
This engine is designed to operate on gasoline. The
emission control system for this engine is EM (Engine
Modifications).
Type of gasoline to use
Always use gasoline that meets these requirements:
xClean, fresh, unleaded gasoline.
xA minimum of 87 octane/87 AKI (91 RON). At
altitudes over 5,000 feet, see “High-altitude use”.
xGasoline with up to 10% ethanol (gasohol) or up
to 15% MTBE (methyl tertiary butyl ether), is
acceptable.
xUse of any gasoline other than those approved
above will void the engine warranty.Some
areas require that fuel pumps be marked if the
gasoline contains alcohols or ethers. If you are not
sure if your gasoline contains alcohol or ethers that
are different than those approved above, then
check with the service station operator.
xDo not modify the engine fuel system or
carburetor to run on alternative fuels.
xNever mix oil with gasoline.
Gasoline Storage
Follow these guidelines when storing gasoline for
longer than 30 days:
xIf fuel stabilizer is used, you do not need to drain
gasoline prior to storage.
xIf no fuel stabilizer is used, then always remove
gasoline from engine during storage.
Fuel stabilizer
xIf you do not want to remove the gasoline, add a
fuel stabilizer to any gasoline left in the fuel tank. A
fuel stabilizer will minimize gum deposits and acids.
If the fuel tank is almost empty, mix the fuel
stabilizer with fresh gasoline in a separate
container and add the mixture to the fuel tank.
Always follow the instructions on the stabilizer
container. Start the engine. Let the engine run for 3
minutes to allow the mixture to reach the
carburetor.
High-altitude use
At higher altitudes (over 5,000 feet), 85 octane / 85
AKI (89 RON) gasoline can be used. Operation at
high altitude may require a high-altitude carburetor jet
kit to improve performance and decrease fuel
consumption.
Adding Fuel
1 Stop the engine. Before you remove gas cap (A),
let the engine cool at least 2 minutes.
2 Remove the gas cap. Fill the fuel tank (B) to
approximately 1-1/2 inches below top of neck to
allow for fuel expansion. Be careful, do not overfill.
3 Before starting the engine, replace the gas cap.
A
B
Figure 7: Gas Cap
Gasoline and its vapors are
extremely flammable and explosive.
Fire or explosion can cause severe
burns or death.
When Adding Fuel
xStop the engine. Let engine cool at least 2
minutes before removing the gas cap.
xFill fuel tank outdoors or in well-ventilated
area.
xDo not overfill fuel tank. Fill tank to
approximately 1-1/2 inches below top of neck
to allow for fuel expansion.
xKeep gasoline away from sparks, open
flames, pilot lights, heat, and other ignition
sources.
xCheck fuel lines, tank, cap, and fittings
frequently for cracks or leaks. Replace if
necessary.
WARNING

13
How To Start The Engine
Engines give off carbon monoxide, an
odorless, colorless, poison gas.
Breathing carbon monoxide can
cause nausea, fainting or death.
WARNING
xStart and run engine outdoors.
xDo not start or run engine in enclosed area,
even if doors or windows are open.
This engine was shipped from the factory without
oil. If you start the engine without oil, the engine
will be damaged beyond repair and will not be
covered under warranty.
CAUTION
1 Before starting the engine, make sure to raise the
blade. To raise the blade, move the depth control
lever (D) forward until the blade will not contact the
ground. See Figure 8.
Rotating parts and belts can contact
or entangle hands, feet, hair, clothing,
or accessories.
Traumatic amputation or severe
laceration can result.
WARNING
xKeep hands and feet away from rotating parts.
xBefore starting the engine, raise the blade so
that it will not contact the ground.
B
C
Figure 8: Operating Controls
D
2 Push the primer button (A) three times. Wait
approximately two seconds between each push.
SeeFigure9.
IMPORTANT: Do not use the primer button to
start a warm engine.
A
Figure 9: Primer Button
3 With your left hand, pull back and hold the engine
stop lever (B) in the operating position. See
Figure 8.
4 To start the engine, hold the starter rope handle
(C) firmly with your right hand.
5 Slowly pull the starter rope handle until resistance
is felt, then pull quickly. DO NOT allow the starter
rope to snap back. Let the rope slowly rewind. If
the engine fails to start after three pulls, push the
primer button two times and again pull the starter
rope handle.
6 If assistance is needed, see the “Troubleshooting”
Chart.
Rapid retraction of starter cord
(kickback) will pull hand and arm toward
engine faster than you can let go.
Broken bones, fractures, bruises or
sprains could result.
WARNING
xBefore starting the engine, make sure to raise
the blade.
xWhen starting engine, pull the starter rope
handle slowly until resistance is felt, then pull
rapidly.
xRemove all external equipment/engine loads
before starting engine.
xDirect-coupled equipment components such
as, but not limited to, blades, impellers, pulleys,
sprockets, etc., must be securely attached.

14
How To Stop
Emergency Stopping
Release the engine stop lever (A). See Figure 10.
Normal Stopping
Move the depth control lever (B) forward to raise the
blade. Then, release the engine stop lever (A) (see
Figure 10).
Figure 10: Operating Controls
B
A
How To Use The Depth Control Lever
xKeep a safe distance from rotating blade
during operation.
WARNING
Thrown debris can cause severe
laceration.
1 Start the engine.
2 To lower the cutting blade (C), pull the depth
control lever (B) back. To raise the cutting blade,
push the depth control lever forward (see
Figure 11).
3 Select the edging depth that you need.
NOTE: For deep edging, first cut at shallow
depths. Then, cut at greater depths until the
desired depth is obtained.
Rotating parts can contact or entangle
hands, feet, hair, clothing, or
accessories.
Traumatic amputation or severe
laceration can result.
WARNING
xOperate equipment with guards in place.
xKeep hands and feet away from rotating parts.
xTie up long hair and remove jewelry.
xDo not wear loose-fitting clothing, dangling
drawstrings or items that could become
caught.
xNever leave the unit unattended while the
engine is running.
xKeep bystanders away from machine.
B
Figure 11: Depth Control
C
C
B

15
How To Use The Index Lever
The cutting angle of the blade is controlled by the
index lever (A). The index lever has four cutting
positions, one vertical cut and three bevel cut position.
The three bevel cutting positions cut a trench at an
angle and reduce the need to edge as often.
WARNING
1 Stop the engine. Do not change the position of the
index lever while the engine is running.
2 Raise the blade. See “How To Use The Depth
Control Lever” in the Operation Section.
3 For a vertical cut (C), set the index lever in position
(0_) See Figure 12.
4 For a bevel cut (B), set the index lever in one of
the three bevel positions (15_,15_,30_). See
Figure 12.
5 Start the engine.
6 Move the depth control lever to the desired height.
See “How To Use The Depth Control Lever” in the
Operation Section.
NOTE: For deep edging, first cut at shallow
depths. Then, cut at greater depths until the
desired depth is obtained.
Rotating parts can contact or entangle
hands, feet, hair, clothing, or
accessories.
Traumatic amputation or severe
laceration can result.
WARNING
xBefore you adjust the wheels or change the
position of the blade, release the engine stop
lever to stop the engine.
xDo not change the position of the index lever
while the engine is running.
xChange the cutting angle of the blade only
when the engine is not running.
Figure 12: Index Lever
A
30
_
15
_
0
_
30
_
15
_
B
C
0
_
15
_
15
_

16
How To Operate The Edger
The edger is designed to cut a small trench along
sidewalks and driveways or to trim close to trees,
flower beds, lampposts, etc. The main reason for
edging is to enhance the overall appeal of the yard. A
cleanly--edged yard gives a nice, overall finished look.
Always dress properly to protect against flying debris.
Wear substantial shoes, long pants and close--fitting
clothes that are not likely to get caught in the
machinery. Also, make sure to wear safety glasses or
goggles.
Thrown debris can result in foreign
objects being thrown into the eyes,
which can cause severe eye damage.
WARNING
xAlways wear safety glasses or eye shields while
you assemble, operate or do maintenance to
the unit.
To reduce the risk of flying debris, inspect the area
and remove any stones, sticks or other objects that
could be thrown by the edger.
If the lawn has not been edged in a while, it may take
several passes to obtain a nice, clean edge.
Because the front wheel and the right rear wheel are
adjustable, the edger can be used on uneven
surfaces, such as the curb shown in Figure 14.
NOTE: References to the right or left side of the
edger are from the viewpoint of the operator’s
position behind the unit.
1 Before you start the engine, move the depth
control lever (D) forward until the blade (A) will not
contact the ground.
2 When edging along a concrete driveway or
sidewalk, set the wheels on the concrete and
position the blade along the left side of the
driveway. To position the edger on a curb, see the
“Curb-hop feature” section. To keep the blade from
hitting the driveway, make sure to keep the blade
guide (B) aligned with the side of the driveway
(see Figure 13).
3 Start the engine. See “How To Start The Engine”.
4 Move the depth control lever back to lower the
blade. Do not try to edge too deep. It may take
several passes to obtain a nice clean edge.
5 Stand behind the edger and firmly hold the handle
(D). See Figure 13. As the blade begins to cut,
slowly move forward.
6 Proceed at a moderate pace until you are
comfortable with the handling of the edger.
NOTE: To operate on a curb, see the “Curb-hop
feature” section.
C
A
B
D
Figure 13:Operation Of Edger

17
Curb-hop feature
1 Stop the engine. Never adjust the wheels while the
engine is running.
2 Set the index lever at vertical cut position to
prevent blade contact with the curb. The maximum
height of a curb should not exceed 8 inches.
3 Set the entire edger on the curb.
4 In the correct position, both the right rear wheel (A)
and the front wheel (B) are off to the side of the
curb and the left rear wheel is on the curb as
shown in Figure 14. Position the edger to allow the
wheels to be lowered.
5 Loosen the rear wheel knob (C) to lower the right
rear wheel to the pavement. Make sure the edger
is level from side to side and tighten the rear wheel
knob.
6 Use the depth control lever (D) to lower the front
wheel to the setting where the front wheel touches
the pavement and the edger is level.
Rotating parts can contact or entangle
hands, feet, hair, clothing, or
accessories.
Traumatic amputation or severe
laceration can result.
WARNING
xNever adjust the wheels or the blade while the
engine is running.
xWhile the engine is running, never leave the
unit unattended.
xKeep bystanders away from machine.
Figure 14: Curb-Hopping Feature
D
A
B
C

18
Edging Tips
xEdging is best performed when conditions are dry.
If the soil is too wet, dirt becomes packed around
the blade causing premature belt wear and
decreased performance.
xIf dirt does become packed around the blade, stop
the engine and remove the wire from the spark
plug. Remove the packed dirt and debris from the
blade.
xFor deep edging, first cut at shallow depths. Then,
cut at greater depths until the desired depth is
obtained.
xFor uniform edging, make sure the blade guide
rides on the surface.
xBefore you begin mowing, try first edging around
the lawn. Use the edger along hard edges such as
sidewalks and driveways.
Rotating parts can contact or entangle
hands, feet, hair, clothing, or
accessories.
Traumatic amputation or severe
laceration can result.
WARNING
xOperate equipment with guards in place.
xKeep hands and feet away from rotating parts.
xTie up long hair and remove jewelry.
xDo not wear loose-fitting clothing, dangling
drawstrings or items that could become
caught.
xBefore unclogging the blade or making
repairs, stop the engine by releasing the
engine stop lever. Disconnect the wire from
the spark plug.
xNever leave the unit unattended while the
engine is running.
xKeep bystanders away from machine.