Craftsman EZ3 917.256552 User manual

917.256552 OWNER'SMANUAL
_0Assembly
oOperation
0Customer Responsibilities
_Service and Adjustments
Repair Parts
C
_AUTIONo Read and follow all safety rules and instructions before operating this equipment.
FOR CONSUMER ASSISTANCE HOT LINE, CALL THIS TOLL FREE NUMBER: 1-800-659-5917

SAFETY RULES
Safe Operation Practices for Ride=On Mowers
WMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS,
FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH.
L GENERAL OPERATION
, Read, understand, and follow afl instructions in the manual
and on the machine before starting,
, Only allow responsible adults, who are familiar with the
instructions, to operate the machine.
oClear the area of objects such as rocks, toys, wire, etc.,
which could be picked up and thrown by the blade.
', Be sure the area is clear of other people before mowing. Stop
machine if anyone enters the area.
Never carry passengers.
Do not mow in reverse unless absotuteiy necessary. Always
took down and behind before and while backing.
, Be aware of the mower discharge direction and do not point
it at anyone. Do not operate the mower without either the
entire grass catcher or the guard in place.
SIow down before turning.
o Never leave a running machine unattended. Always turn off
blades, set parking brake, stop engine, and remove keys
before dismounting.
• Turn off blades when not mowing.
Stop engine before removing grass catcher or unclogging
chute.
,, Mow only in daylight or good artificial light:
o Do not operate the machine while under the influence of
alcohol or drugs.
o Watch for traffic when operating near or crossing roadways.
oUse extra care when loading or unloading the machine into
a trailer or truck.
WI. SLOPE OPERATION
Slopes are a major factor related to loss-of-control and
tipover accidents, which can result in severe injury or
death. All slopes require extra caution. If you cannot back
up the slope or if you feel uneasy on it, do not mow it.
DO:
• Mow up and down sIopes, not across.
Remove obstacles such as rocks, tree limbs, etc.
,, Watch for holes, ruts, or bumps. Uneven terrain could
overturn the machine. Tall grass can hide obstacles.
• Use slow speed. Choose a low gear so that you will not have
to stop or shift while on the slope.
,, Follow the manufacturer's recommendations for wheel
weights or counterweights to improve stability.
Use extra care with grass catchers or other attachments.
These can change the stability of the machir.
Keep all movement on the slopes slow and g;aduaL Do not
make sudden changes in speed or direction.
Avoid starting or stopping on a slope, if tires lose traction,
disengage the blades and proceed slowly straight down the
slope.
DO NOT:
,Do not turn on slopes unless necessary, and then, turn slowly
and gradually downhill, if possible.
Do not mow near drop-offs, ditches, or embankments. The
mower could suddenly turn over if a wheel is over the edge
of a cliff or ditch, or if an edge caves in.
Do not mow on wet grass. Reduced traction could cause
sliding.
oDonottrytostabilizethemachinebyputtingyourfootonthe
ground.
o Do not use grass catcher on steep slopes.
2
III. CHILDREN
Tragic accidents can occur if the operator is not alert to the
presence of children. Children are often attracted to the
machine and the mowing activity. Never assume that
children witl remain where you last saw them.
o Keep children out ofthe mowing area and under the watchful
care of another responsibie adult.
Be alert and turn machine off if children enter the area.
o Before and when backing, look behind and down for small
children,
Never carry children They may fail off and be seriously
injured or interfere with safe machine operation.
oNever allow children to operate the machine.
o Use extra care when approaching blind corners, shrubs,
trees, or other objects that may obscure vision.
_V. SERVICE
o Useextracarein handli _gasolineandotherfuels. Theyare
flammable and vapors _e explosive.
Use only an approved container.
Never remove gas cap on add fuei with the engine
running; Allow engine to cool before refueling. Do not
smoke.
Never refuel the machine indoors.
Never store the machine or fuel container inside where
there is an open flame, such as a water heater.
Never run a machine inside a closed area.
o Keep nuts and boks, especially btade attachment bolts, tight
and keep equipment in good condition.
Never tamper with safety devices. Check their proper
operation regularly.
,, Keep machine free of grass, leaves, or other debris build-up.
Clean oil or fuel spillage. Allow machine to cool before
storing.
Stop and inspect the equipment if you strike an object.
Repair, if necessary, before restarting.
,Never make adjustments or repairs with the engine running.
Grass catcher components are subject to wear, damage, and
deterioration, which could expose moving parts or allow
objects to be thrown. Frequently check components and
replace with manufacturer's recommended parts, when nec-
essary.
Mower blades are sharp and can cut. Wrap the blade(s) or
wear gloves, and use extra caution when servicing them.
• Check brake operation f ,_quently. Adjust and service as
required.
CAUTION: Always j
disconnect spark plug
wire and place wire where it cannot contact
spark plug in order to prevent accidental
starting when setting up, transporting,
adjusting or making repairs.
WARNING 4&
The engine exhaust from this product contains
chemicals known to the State of California to
cause cancer, birth defects, or other reproduc-
tive harm.

CO_Grs_A _.LAo_©[iS o"l your pumhase of a .:_eals
Traetor I[_"-_asbeen des[qned,,.,engir:emed and manufac-
tured Io give you the best possibie dependabiitv arid
Should you experience any probbm you cannot easiiy
remedy, piease contac[ your nearest Sears Authorzed
Sewice Cente_/DepaS:ment Department. We have corm
potent wetbtrained technicians and the proper too!s to
service or repair this tractor,
Please read and retain Ibis manual. The nstructions wll
enable you to assemble and maffstainyour tractor pmper!y
Atways observe the '_SAFETYRULES".
•,1rJMBEs 9 t /._5650_z
SERIAL
iNUMBER ................................................................................
IUATL:OF P[J[:{CqA,oE
H_ 71ODE<./_,NDSERi£,_.}JMBERSWIL_.BET,JU,.ID
ON A PLATE UNDER THE SEAT.
YOU SHOULD RECORD BOTH SERIAL NUMBER AND
DATE OF: -_i ' " IN
lo,,,.RCHASE AND KEEP A SAFE PLACE
FOR FU, URn=REFERENC_
.NAN¢_ AGREEMEN F
A Sears Maintenance Agreement isavaiiabie on this prod-
uet Contact your nearest Sears store :[ordetaiis
Read and observe the safety rutes
_', Foitow a _'eguiarschedute in maintaining, caring for arid
Foilow the instructions under "Customer Responsibilb
des _kd "Storage" sections of this owne_ s manuak
WARNING: This t_actor is equipped with an ntemat
combustion engine and shouid not be used on or near any
HORSEPOWER: ! 5.0
GASOL NE CAPAC TY t,25 GALLONS
ANC, TYPE: _NLEADED REGULAR
OIL TYPE (APFSF/SG): SAE IOW30 (above 32°F}
SAE 5W-30 (beiow 32°P)
OIt CAPACi]Y: W/FILTER: 40PNTS
W/O FILTER: 3,5 PINTS
.._,AMP,JN RC12YC
SPARK PLUG: ¢'_' _ _ '
G£P: 040")
VA_.vl: ,.;LhARAN<;E; NO'T, D..USTABLE
GROUND SPEED(MPH): FORWARD: 0 5.5
REVERSE: 0-24
T_RE_-'RESSURE: FRONT: !4 PSI
REAR: !0 PSi
CHAR,s.NGSYSTEM: 3 AMPS BATTERY
5 AMPS HEADLIGHTS
=
"BA rTERY: AMP/HR: 30
MIi'4.CCfa,: 240
CASE SIZE; UIR
I BLADE BOLTTORQUE: 30-35 FT. LBS
unimproved forest_covered brash,covered or grass-cov-
ered and unless the engines exhaust system is equipped
with a spark arrestor meetin¢] applicable locai or state taws
(ifar;y)_ f a spa,_ka testa s Used ii should be ma r_,tained
n effective working order by Ihe operator.
n the state of California the above is required by law
{Section 4442 of Ihe Caiifornia Pubic Resources Code}•
Other states may have simiiar laws. Federal laws apply on
federai !ands. A spad< arrestor for'the muffler is available
through your r_earest Sears Au[horized Service Cartier/
Depa_'ment (See REPAR PARTS section ofthis manual}.
LH q TED TWO YEAR WARRANTY ON ",JRAFTS[VIAN F{ DING E@UIP aENT
For two ,,_)years from thedate of pumhase,if this CraftsmanRiding Equipment is maintained,iubdcated and tuned up according
to the nstrJctio<_sin theowner'smanuai, Searswit! repair or re,aiace free ofcharge, any parts found to be defective in material or
1'hisWarrantydoes hotcover:
o Expendableitemswhichbecomewornduring normaluse, such as blades, sparkplugs, aircleaners, belts,etc.
Tire replacementor repaircaused bypuncturesfrom outside objects,such as nails,thorns, stumps,or giass.
o Repairsnecessar£becauseofoperatorabuse negligence,improperstorage or accident or thefaiiure to maintain the
equipment according tothe instructionscontained in the owners manuei.
'o Ridingequipment usedforcommercialor reniai purposes.
L Ba TED 90 DAY WARRANTY ON B qTERY
or r_ff_ety(go} days from date of purchase,if any batteqi inck._dedwth his riding equipment proves defective in material or
workmanship and our testing determir_esthe battery witlnot hold a charge, Searswill_ep!ace the baiter,/at no charge.
N,-HOME WARRANTY SERVICE ON YOUR CRA_SMAN RtD_NG EQ IPMENT IS AVAILABLE AT NO-CHARGE FOR 30
DAYS FROM THE DATE OF PURCHASE PLEASE CONTACT YOUR NEAREST SERVICE CENTER. AFTER 30 DAYS FROM
"r'HE DATE OF PURCHASE, WARRANTY SERVICE iS AVAILABLE BY TAKING YOUR CRAftSMAN RIDING EQU!PMENT TO
YOUR NEAREST SEARS SERVICE CENTER. (!N.-HOME WARRANTY SERVICE WILL STLL St:!;iAVA LABLE AFTER 30 DAYS
FROM THE DATE OF PURCHASE BUT A STANDARD TRIP OflARGE WILL APPLY.') T'IS WARRANTY APPLIES ONLY
WI41LETHIS PRODUCT !S _NTHE UNITED STATES.
This Warranty gves you epecific egat fights and you may also have other _ignts which may _a_y from state to state
.'_c.ARo ESTA'FES, L_d¢.}=-! s_AhROE[V£_<,KA 4_ "*• "-wO, D/817 WA,

TABLE OF CONTENTS
SAFETY RULES ............................................................ 2
PRODUCT SPECiFiCATIONS ...................................... 3
CUSTOMER RESPONSIB_LmES ..................... 3. !5-t9
WARRANTY .................................................................. 3
TABLE OF CONTENTS ................................................. 4
iNDEX ............................................................................ 4
TRACTOR ACCESSORIES ......................................... 5
ASSEMBLY ............................................................... 7-9
OPERATION ......................................................... 10-14
MAINTENANCE SCHEDULE ..................................... 15
SERVICE AND ADJUSTMENTS ........................... 20-25
STORAGE ................................................................... 26
TROUBLESHOOTING ........................................... 27-28
REPAIR PARTS - TRACTOR ................................ 30-47
REPAIR PARTS- ENGINE .................................... 48-53
PARTS ORDERJNGISERV_CE .................. BACK PAGE
iNDEX A
Accessories ....................................... 5
Adjus_rnen_s:
Brake ........................................... 22
Carburetor .................................... 25
Mower:
Front-To-Back ...................... 2I
Side-To-Side .......................... 2t
Throttle Control Cable ................. 25
Air FHter, Engine ................................. 18
Air Screen Engqe ............................. '_8
Assembly ........................................... 7-9
B
Battery:
Charging ................................ 7 8
Cleaninc ...................................... 16
Starting w_th Weak Battery ....... 24
Storage ...................................... 26
Terminals .................................... I6
Belts:
Motion Drive
Removal/Repiacem_nt ........... 22
Mower Blade Drive
Removal/Replacement ............22
Blade:
Sharpening ................................... 16
Replacement ................................ 16
Brake Adjustment ................................ 22
C
Carburetor Adjustment ....................... 25
Controls, Tractor ................................. ! I
Customer Responsibilities .......... 3,I5-19
Engine:
Air Filter .................................... 18
Air Screen, Engine .................. 18
Battery ...................................... 16
Cooting Fins, Engine ............... 18
Engine Oil ................................ t7
Fuel Filter ................................ 19
Spark Plugs .............................. 18
Tractor:
Blades ...................................... t6
Lubrication Chart ..................... 15
Maintenance Schedule ........... 15
Tire Care ......................... 8,16,23
Cutting Height, Mower .......................... t2
E
E,_ectrical:
Interlocks and Reiays ................ 24
Schematic ................................... 29
Wiring Diagram ........................... 30
E_gine:
Air Filter ....................................... 18
Air Screen .................................. 18
Cooling Fins Eng ne ................... 18
Oil Change ................................. 17
Oil Level ................................. 13.17
Qi! Type .................................. 17
Preoara_tor ................................ 13
Reoair Parts ........................... 48-53
Starting ....................................... 4
Storage ................................... 2_
F
FlUters:
Air ............................................... 18
Fue_............................................. 19
Ft_ef
Type ............................................ 13
Storage ....................................... 26
Fuse ................................................... 24
G
Gauge Wheels ..................................... 8
H
F_'oodRemoval/installation ................. 24
L
Leve_ingMower Deck ......................... 2!
Lt_brication Chart ................................ 15
M
Maintenance Schedule ...................... 15
Mower:
Adjustment, Front-to-Back .......... 21
Adjustment, Side-to-Side ........... 2!
Blade Sharpening ....................... 16
Blade Replacement ..................... 16
Cutting Height ............................. 12
Installation ................................... 20
Operation ............................... 12-13
Removal ...................................... 20
Mowing Tips ....................................... 14
Muffier ................................................ t 8
.Spark Arrester .......................... 3,40
Muicher Plate ....................................... 9
O
Oil: Cold Weather Conditions ....... 13,17
Engine ......................................... 17
Storage ...................................... 26
Ooeration .................................... 10-t4
Operating Mower ..............................
.12-I3
Ootions:
Accessories ................................ 5
Seark Arrester ........................ 3.40
P
Parking Brake ................................ 1I-i2
Parts Bag ............................................ 6
Parts. ReDlacementJRepair ........... 30-47
Product Specifications ......................... 3
R
Reeair Parts .................................. 30-47
S
Safety Rules ....................................... 2
Seat ...................................................... 8
Service and Adjustments .............. 20-25
Brake ........................................... 22
Carburetor .................................. 25
Fuse ............................................ 24
Hood Removal/Installation .......... 24
Motion Drive Belt
Removal/Replacement ........... 22
Mower Blade Drive Belt
Removal/Replacement ........... 22
Mower Adjustment:
Front_to-Back ......................... 21
Side-to-Side ........................... 21
Mower Installation ....................... 20
Mower Removal .......................... 20
Tire Care ............................. 8,16,23
Slope Guide Sheet ............................. 55
Spark Plugs ........................................ 18
Specifications ....................................... 3
Starting the Engine ....................... ! 3-t4
Steering Wheel ................................ 7,23
Stopping the Tractor ........................... 12
Storage ............................................... 26
T
Throttle Control Cable Adjustment ..... 25
Tires ........................................... 8,16,23
Trouble Shooting Chart .................. 27-28
Transaxle Repair Parts ................. 46-47
W
Warranty ............................................... 3
Wiring Diagram .................................. 30
Wiring Schematic ............................... 29

TheseaccessoriesandattachmentswereavailablethroughmostSearsro_ailoutletsandservicecenterswhenthetractorwaspurchased.
MostSears stores can order these items for you when you provide the model number of your tractor.
ENGINE AiR FILTER
PERFORMANCE
Soars offers a wide variety of attach ments that fit your tractor. Many ofthe_seare listed below with brief explanations of how they can help
you. This _istwas current at the time of publication; however, it may change in f_tUre years -more attachments may be added, changes
may be made in these attachments, or some may n° longer be available or fit your modet Contact your nearest Sears store for the
accessories and attachments that ate available for your tractor.
Most of these attachments do not require additional hifches or conversion kits (those that do are indicated) and are designed for easy
attaching and detaching.
AERATOR promotes deep root growth for a heaithy lawn Ta S#_OWBLADEIorsnowremovatorfiy. 14dnch high,48dnchwide
pered 2.5 inch steel spikes mounted on !0-inch diameter discs _;adec_ears42-inch pathwhen angledld_or dghL Ra!Ses, lowers
puncture holes in soil at Cose intervals to Jet moisture soak in. _;_rlside tever: Adjustable skids; repiaCeabJe, revers Ibte scraper
Stee we ght tray for increased penetrat on ba_. (Use with t re c qa ns'and whee we ghts and/or rear drawbar
BAGGER lets you cottect grass c}ippings and teaves for a
heafthier, nester looking iawn. Two Perrnanex containers hold
30-gallon ptastic bags.
BUMPER protects front end of tractor from damage.
CARTS make hauling easy. Variety of sizes available, plus
accessories such as side panel kits, tool caddy, cart cover,
protective mat and doily.
CORING AERATOR takes smafi piugs out of so_ to allow mois-
ture and nutrients to reach grass roots, 36dnch swath. 24
hardened steel coring tips. 150 lb. capacity weight tray.
EASY OIL DRAIN VALVE makes oil changes easier, faster.
FRONT NOSE ROLLER canters in front of mower deck to reduce
chances of "scalping" on uneven terrain.
GANG NtTCN lets you tow 2 or 3pull-behind attachments _t once,
such as sweepers, dethatchers aerators (not for use with toilers,
carts or other heavy attachments).
GAUGB WHEELS on both sides of the mower deck reduce
chances of"scalping" on uneven terrain• For mower decks not so
equipped.
MULCH RAKFWDETRATCHER !oosens soil and flips thatch and
matted leaves to lawn surface for easy pickup. Twenty spring tine
teeth. Useful to prepare bare areas for Seeding. Available forffont
or rear mounting. RI_GH PERFOR_d_ANCE REEL_ACTION
SPRING T_NE DETHATCHER covers 36-inch wide path and
tosses thatch into large hopper, Mounts behind tractor,
MULCHING CLOSE-OUT PLATE K_T, once instaJied, Jets you
muich, discharge or bag clippings (bagger optional) wi[hout
changing blades. For models not equipped as 3din1 Convertible
mowers. See "MOWER" in the Repair Parts section of this
manuai,
RAMP TOPS AND FEET let you load and unload tractor from a
pickup truck. Use with 2 x 8 or 2 x I0 Iumber.
ROLLER for smoother iawn surface. 36dneh wide, 18dnch
diameter water-tight drum holds up to 390 Ibs_of weight. Rounded
edges prevent harm to turf, Adjustable scraper automatically
cleans drum.
SN()_,P_HROWER has 40dnch swath. Drum-.type auger handles
powdery and wet!heavy snow. Mounts easily with simple pin
arrangement. Discharge chute adjusts from tractor seat. 6dnch
d_ameter spout discharges snow 10 to 50 feet. Lift controlled at
tactor seat. (Use with chans and wheei weights and/or rear
SPRAYERS use 12welt DC electric motor that connects to the
lractor batten/ or other 12-volt source. Includes booms for
automatic spraying and hand he!d wand for spot spraying, Wand
fas adjustaMe spray pattern. For apptying herbicides, insecti-
cides, fungicides and liquid fertilizers.
SPREADBRiSEEDERS make seeding, fertilizing, and weed kilt-
_sgaasy_ Broadcast spreaders are also usefuI for granular de-
icers and sand.
'Sh_JE:EPERSlet you coi/ect grass c ippings and leaves.
!;_I:and depth control system and does NOT reqL 'e a s eeve hitch
R{Sany iawn, yard Orgarden tractor. Simply hook up to the tractor
a_awbar and g0! Optional accessories convert unt for
@thatching, aerating hilling...without tools.
T_RBCHAINS are heavy duty; ciOsety spaced extra-large cross
}}_ksgive smooth ride, outstanding traction.
*fRAC_OR CAB has heavy duty vinyt fabric over tubular steel
frame, ABS piastiC !op; ciear p!astic windshield offers 360 degree
visibility: Ringed 'netai doors with catch. Keeps operator warm
and dv Remove vinyl sides and WindShields for use as sun
_:,roi_ct0rin summer, Optio_"_a! accessories include: tinted/
• operated wiper;tempered s0iid Safety glass Wncshe d Wth harid
12-volt amber caution }ight for mounting on Cab top.
stACS for poweffui coitection of heavy grass c!ippihgs and leaves,
O#tio_at wand attachment to pick up debris in hard4o_reach
p_aces. VACiCH_PP_R includes a chipper-shredder,
W_!GHT BRAC_(_T for drawbar for snow removal applications.
t_ <5Jses (..,. lb. weight.
_HBEL WB_GHTS for rear wheels provide needed traction for
*r ct_e ,ate,
snow removal or ._ozing heavy _.+ _u,,

OF H E
RaGs Bag oontents shown 'full size
/,
/
/
/
f
/
/
_4 ) Hex Bo_t
8/8 I6 x I
(I) Lar@eFiat Washer (t) U>ckwasher 318
(i) Locknut
5/I6-,!8
(1) I4ex Boit 5/16-18 sti-I_4
{{...........
{1) Hex Bolt
!/213 x i
/" (!} Washer
I.-3ll £x 12
Gauge /
!j'
(1} Leck Wad-her i/
(2) Screws
#10x 518
#10
\\
8/16 x 3/4 _ (2) Wetd
x 16 Gauge Nuts #10
(2) Hex Bo!ts I/4-20 x 3/4 (2) Hex Nuts 114.__.0
z_ Washers 9/32 x 518x _ Gauge
Parts packed separately in carton
Ses.t
', / /
Video
Cassette
/i
q
7Yhee, _{?lbleher
Plate
Manua
i i
Boot Parts Bag
(2} Center-
lock Nuts
(2) Keys
Assemblys
tt }} Wheel
\}, ..................// lnser_
Extension
bnafl

Yournewtractorhasbeenassembledatthefactoryw_thexceotion of hose parts left unassembled for shipping purposes.
To ensure safe and proper operation of your tractor all carts and hardware you assemble must be figr_tened securely. Use
the correc_ loots as necessary to insure proper tJghmess.
TOOLS REQUIRED FOR ASSEMBLY
A socket wrench set wilt make assembly easier. Standard
wrench sizes are Iisted.
tU 5J16" wrench
_2t 7/!6" Nrencnes
_ _ //2" wrer_cn
(2} 9/I6" wrench
I _ 3/4" Secket w/afire rachel
Philliss Screwdriver
Tire oressure gauge
Utility knife
When right or eft hand is mentioned m rots manual, it
means when you are in the operating oosition (sea_ee
behind the s_eermg wnee_ !,
TO RE,lOVE TRACTOR FRON! CARTON
STEERING
--.'_ WHEEL _NSERT
....... 3/8 HE:X BOLT
......... 318LOCK WASREF!
WASHER
°_. STEERING
-" WHEEL
STEERING
BOOT _ .....
EXTENSI!ON
UNPACK CARTON AOAPTER,. - /SHAFT
Remove al accessible loose oa_s ana carts canons 5/16HEXBOLT
Trom capon (See page ] L .,. :
,Cut, from top to bottom, atong lines on alt four comers _J .'i! _'
of carton, and Iay panels fiat. _ -:-,
1 4 /- : _
Check for any additional loose parts or cartons and 5/,6 LOCI(NUT ,' " .... .
remove, i /" "
BEFORE ROLUNG TRACTOR OFF SKID
A°FACH STEERiING WHEEL (See Fig, 1)
ASSEMBLE EX'TENSION SHAFT AND BOOT
Slide extension shaft onto lower steering shaft, Align
mounting holes in extension and iower shafts and
install 5/t6 he>:bolt and Iocknut. Tighten securely.
I_tPORTANT: TIGHTEN BOLT AND NUT SECURELY TO
18_22 FT LBSTORQUE.
o Place tabs of sleeting boot over tab slots in dash and
push down to secure.
iNSTALL STEERING WHEEL
Position front wheeis of the tractor so they are pointing
straight foPTvard.
o Slide steedng wheel adapter onto steering shaft exten-
sion.
o Position steering wheel and sleeve assembly so cross
bars are horizenta! (left to right) and slide onto adapter.
o Assemble large fiat washer, 3/8 iock washer, 3/8 hex
bolt and tighten securely
o Snap steering wheel insert into center of steering
wheel.
Remove protective pastic from tractor hood and grill.
IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES
IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR
IS TO ROLL OFF SKID.
TO ROLL TRACTOR OFF SKID (See Opera°
tier section for tocation and function of con.,,
F_G. !
Place freewheel control in freewheefing position to
disengage transmission (See "TO TRANSPORT ° in
the Ogeration section of this manua!).
Roil tractor backwards off skid.
Remove banding holding discharge guard up against
tractor
HOW TO SET UP YOUR TRACTOR
CONNECT BAKERY (See Figs, 2 and 3}
CAUTION: Do not short battery term_
na_s: Before eormecting batterj_ re_
move metal bracelets, wristwatch
bends, rings_ etCo
Positive terminal must be connected
first to prevent sparking from acciden-
o Remove cardboard packing from seat pan and tiffseat
pan to raised position.
Open battery box door.
e
Press rift lever p{unger and raise attachment lift lever to
its highest position
o Reiease parking brake by depressng clutch/brake
Remove terminal proteciive caps end discard.
If this batten/isput into service after month and year
indicated on label (!abel located between terminals)
charge battery for minimum of one hour at 6-10 amp&
First connect RED batter,! cable to positive (+) terminat
with hex boit, flat washer, lock washer and hex nut as
shown, Tghten securely.
Connect BLACK grounding eabte to negative (-}_fermi-
nai with remaining hex bott flat washer lock washer
and hex nut. Tighten secureiy_
Close battery be)( door.

ASSE
Open battery box door lot':
o Inspection for secure corlnections (to _ig_'ten hard
Inspection Ior corrosion.
_* Testing batteG,
Jumping (f required}
o Periodic ci_arging.
POSIT!VE B_SCARD
{RED) CABLE TERMINAL
, PROTECTIVE
.-.. /CAPS
i ' NUT
LOCK
WASHER
/
/PLAT
WASHER
HEX
BOLT
NEGATIVE
(BL ACE) CABLE
F_G....
SEAT
PAN
BATTERY
BOX DOOR
FtGo3
_NSTALL SEAT (See Fig° 4)
Adiust seat before tightening adjustment bott
o Remove cardboard packing on seat pan
0_ Place seat on seat pan and assemble shoulder bolt.
Assemb!e adjustment boIt bck washer and fiat washer
looseIy Do not tighten.
Tighten shoulder boit securety
SEAT
SEATPAN
Lower seat into operating position and sit on seat.
o Slide seat until a comfortable position is reached which
a!ows you to press dutch/brake pedal a_Ithe way
down,
Get off seat without moving its adjusted position.
o Raise seat and tighter adjustment bolt securely.
CHECK TIRE PRESSU!!_E
The tires on your tractor were overinfiated at the !actor/for
shipping purposes. Correct tire pressure is irnpoRant for
best cutting pedormance.
Reduce tire pressure to PSI shown n "PRODUCT
SPECIFICATIONS" on page 3 of this manual.
CHECK ©ECK LEVELNESS
For best cutting results, mower housing should beproperly
leveled. See "TO LEVEL MOWER HOUSING" in the
Sewice and Adjustments section of this manual•
CHECK FOR PROPER POSITION OF ALL
See the figures thai are shown for replacing motion and
r_iower _lade @;ire betts in the Sergice and AdjustmentS
section of Ibis manual, Verify ihat the belts are rouIed
After you ieam how _ooperate your tractor, check to see
that the brake is propedy s.diusted, See "TO ADJUST
BRAKE' in the Service and Adjuslments section of this
rnanual_
ASSEMBLE GAUGE WHEELS TO MOWER
DECK (See Fig. 5)
Assemble gauge wheeis with tractor on a flat level surface
,_ Adjust mower to desired cutting height (See "TO AD-
JUST MOWER CUTTING HEIGHT" in the Operation
section of this manual),
-_ Wth mower in desired height of cut position, gauge
wheels should be assembled so they are slightly off the
ground. Install gauge wheel in appropriate hole with
shouider bolt, 3/8" washer and 3/8o16 tocknut and
tighten securely.
,, Repeat for opposite side installing gauge wheel in
same adjustment hole. ]
l
/" \
3/8- t 8
GAUGE WHEEL j .....kSHOULDER
BOLT
F'iGo4 FIG,, 5

_NSTALL MULCHKR PLATE
{See Figs. 6 & 7}
Install two a[cn nooks _omutcher p_a[eusing screw,
washer, IOCKwasner, and wetd nut as shown,
NOTE: Pre-assembie wetd nut to latch hook by inserting
we_a nut from the top w_th hook oointing down,
Tighten hardware ;ecure_y.
Raise and nolo deflector shield in Jprlght position,
Place front of muiener orate over fret t of mower deCK
opening and slide into p_ace, as shown.
Hook front latch trio note oRfront of mower deck
o Hook rear latch into no_e an back Ofmower DecK.
CAUtiON: Do not remove discharge
guard f_om mower. Raise and hold
guard when attaching muJcher plate
and allow it _o rest on p_ate whi_e in
LATCH
HOOKS
FiG. 7
HOOK POINI"S DOWN
WELD NUT FROM THE TOP jr ....... _
X\ "'S
LOCK
LATCH
J" HOOK
WASHER LOCK
WASHER
WASHER
WELD
NUT
MULCHKR
PLATE
FIG, 6
TO CONVERT TO BAGGING OR
DiSCHARGiNG
Simply remove mulcher plate and store in a safe place.
Your mower is now ready for discharging or installation of
optional grass catcher accessoPy,
NOTE: It is not necessary to changebtades, The mulcher
blades are designed for discharging and bagging also,
BEFORE YOU OPERATE AND ENJOY YOUF_ NEW
TRACTOR. WE WISH TOASSURE TH/I T YOURECEfVE
FHEBESTPERFORMANCEAND SATtSFA C TION FROM
FHIS OLIAL/TY PRODUCT,
PLEASE REVIEW THE FOLLOWING CHECKLIST:
/All assembly instructions have been completed.
/No remaining !dose parts in carton.
_/ Battery is properly prepared and charged, (Minimum
1 hour at 6 amps).
v" Sea{,iS adjusted comfortably and tightened securely,
v' Atttires are properly inflated. (For shipping purposes,
the tires were overinfiated at the factory).
_x Be sure mower deck is properly leveled side-to-side/
frontqo-rear for best cutting results. (Tires must be
properly inflated for ieveiing),
/Check mower and drive belts, Be sure they are routed
properly around pul!eys and nside all belt keepers.
/Check wiring. See thai aHconnections are stiil secure
and wires are properly clamped.
v" Before driving tractor, be sure freewheel control is [n
drive position_
WHILE LEARNING HOW T© USE YOUR E_ACTOR, PAY
EXTRA ATTENTION TO 7-HEFOLLOWING IMPORTANT
FFE/MS:
v" Engine oil is at proper !eveL
/Fuel tank is fiIled with fresh, clean, regular unleaded
gasoline.
/Become familiar with alt controls ,-their location and
function. Operate them before you start the engine.
/Be sure brake system isin safe operating condition.
v' II is important to purge the transm ssion before operat-
ing your tractor for the first time_ Fotlow proper starting
and transmission purging ins!ruetions (See "TO START
ENGINE" and "PURGE TRANSMISSION' in the Opt.
e_ation section of this msn/4aI)

Thesesymbol,_mayappearoryourtractorofinJ[teraturesuppliedwiththeproduct.Learnandunderstandtheirmeaning.
,-- __,, CAUTIONOR REVERSE FORWARD FAST SLOW
WARNING
o i
(_' _ C_" _ _ _L _
EN .xJN_z:ON ENGINE OFF JJL PRESSURE C__UI(..,'t MGHTS ON LIGHTS OFF
_, O_._ MOWER _ .... PARi41NG BRAKE UNLO_._'..E_J
LOCm LOCKED
l \
vlO NER LIFT
RLVERoE NEUTRAL HIG_ LOW
ATTACHMENT
CLUTCH ENGAGED
÷
ATTACHMENT
CLUTCiq DISENGAGED
PARKING BRAKE
IGNtT Ob
'_ _ _ /E_ D • •
DANG_- , _',._::._ HANDS AND FEET AWAY (_ydro Moee _ o y

ii
READ THIS OWNER"S MANUAL AND SAFETY RULSS BEFORE OPERATING YOUR TRACTOR
Compare the illustrations with your tractor to familiarize yourself with the iocati0ns of Various controis and adjustments. Save
this manual for future reference_
THROTTLE/
CHOKE
CONTROL
CLUTCHf
BRAKE
PEDAL
HEIGHT
ADJUSTMEN_
KNOB
FREEWHEEL
CONTROL
AMMETER
\
LIGHT
IGNmON SWITCH
SW_TCH POStT_ON
,, PLUNGER
ATTACHMENT
LIFT LEVER
ATTACHMENT
CLUTCH LEVER
PARKING BRAKE
iI"-:!!LII¸. CONTRoLMOT'ON
_ LEVER
APPROX.
SPEED
3
FiG. 8
Our tractors conform to the safety standards of the AmeriCan National Standards institute.
ATTACHMENT CLUTCH LEVER: Used to engage the
mower blades, or other attachments mounted to your
tractor.
UGHT SW_TCN: Turns the headlights on and off.
THROTTLF__JCHOKE CONTROL: Used for starting and
controlling engine speed.
CLUTCH/BRAKE PEDAL: Usedfordeciutching and brak-
ng the tractor and s_a_ing the engine.
PARKING BRAKE: Locks clutch/brake peda into the
MOTION CONTROL LEVER - Selects the speed and
direction of the tractor,
ATTACN_'_IENT U_ LEVER: Used to raise and lower the
mower deck or other attachments mounted to your tractor.
LIFT LEVER PLUNGER: Used to retease attachment lift
_everwhen changing its position.
_GN_TION SW_TCN: Used for starting and stopping the
engine_
!4EIGHTABJUSTMENT KNOB: Used toadjustthernowe__
FREEWHEL CONTROL: Disengages transmission for
pushing or slowly towing the tractor with the engine off,. A_I_4ETER: Indicates battery charging (+) or dischergi _g
!!

_' °" TRA_J R9 H
TO SEX"PARKH!G BRAKE {See Fig_ 9)
You tractor s equipped with an operator p esence sensing
switch. When engine is running, any attempt by the
operator Io eave the seat without first setting the parking
brake wiil sPut off the engine,
Depress dulch/brake pedat into fuli "BRAKE" position
and hold
P/acs_parking brake iever in "ENGAGED" position and
release pressure from ch4ch/brake pedai Pedal shou!d
remain in "BRAKE" pos tion. Ma_<es_ze parking brake
will llold tractor secure.
A_iTACHMENT CLUTCH LEVER
'_@_SENGAGED"
p
j, POSITION
PARKING BRAKE
"ENGAGBD"
GEARSHIET
.....LEWR
CLUTCH/
BRAKE
PEDAL
"DRIVE' HEIGHT ADJU "_
POSKION MENT _NO8 Uo_, _ON
F_G°9
STOPPerinG (See Fig, 9}
MOWER BLADES ..
o Move attac _ment ciutch ieve' to 'DISENGAGED'* po
sition_
GROUND DRIVE-
_, Depress clutch!brake pedai nto _uit _BRAKE_'positieh_
Move motion control lever to r eutral (N) position,
!MPOATAHT: THE MOTION CONTROL LEVER DOES
NOT RETURN TO NEUTRAL (N) POSIT!ON WHEN THE
CLUTCH/BRAKE PEDAL IS DEPRESSED,
ENGINE -
Mow_ _hrottJecontrol to slow (_) pos tiom
NOTE Faiiure to move throttie centre to sio,¢_(_)
position and ai owing engine to die before stopping rnay
cause engine to 'backfire",
Turn ;gnton key to "OFF' position and remove key.
Always remove key when !eaving tractor to preve@
unauthorized use.
o Never .;se choke to stop engine.
NOTE: Under certain conditions when tractor s standing
die with he engne runnin% h@:erK3ne ex iaus[ gases may
cause "browning* oi grass. To e iminate this possib@!_
always stop engne when stoppin{} tractor orsgrass areas
CAU°_'IOH: A_ways stop t_'actor com_
p_ete% as described above before _eav,-
hg the operator's position:; to empty
grass catcher_ etCo
TO US_:£TRRO_L£ CONTROL (See Fig. 9)
Always operate engine st fuji throttle.
Operating engine at less than ful throttle reduces the
battery charging rate.
o Fuii thro@e offers the best bagging and mower pefforo
rT_ance,
TO _",aOVEFORWARD AND BACKWARD (See
F_go9)
The direction and speed of movemerit is controiled by the
motion control lever
Start tractor with motion control !ever in neu[rat (N)
o Release parking brake and clutch/brake pedal.
o Slowly move motion control !ever to desired position.
TO ADJUST MOWER CUTTING HEIGHT
(See isig,,g}
The cutting height is controlled by turning the height adjust-
mast knob n desired direction,
-. _xrn kK)b c!ockwise (,S:,q) to raise-c_tting height,
*_ -%ira kieb counterclockwise (_-%) to lower cutting
The cutting height range is approximately I o1/2" to 4" The
heights are measured from the g,_oundto the blade tip with
the engine not runnihg. These heights are approximate
and n_ay van/depending upon soil conditions, height of
,grass ad types of grass being mowed.
The average lawn shoutd be cut to approximately 2ol/2
nches during the cool season and to over 3 inches
during hot months. F:or healthier and better ooking
lawns mow often and after moderate growth,
_0 For best cutting pedormance_ grass over 6 inches in
height should be mowed twice. Make the first cut
releNvely high; the second to desired he ght.
TO OPERATE _VtOWER (See Fig, 10)
Your tractor isequipped with an operator presence sensing
switch, Any attempt by the operator to leave the seat with
the engine running and the attachment clutch engaged wil!
shut off the engine,
Select desired height of cut
,_ Lower mower with attachment lift control
S_art mower blades by engaging attachment clutch
control.
_ TO STOP M©WER BLADES - disengage attachment
clutch control.
CAUTION: Do not operate the mower
without either the er_tire grass catcher,,
o_ mowers so equipped, or the dis-

"EN@AGED"
POSITION ATTACHMEHT
LOW
HEIGHT
ADJUSTMENT
KNOB
i V
k.... FIG. I0
TO OPERATE ON HILLS
GL_ABO
o Choose the slowest speed before starting up or down
hi!ls.
Avoid stopping or changing speed on hils.
o if sbwing is necessary, move throttle controi tever to
f stopping is absoiutely necessa%,, push c_uth!bn_ke
pedal qu ckiy to brake pesitk)n and engage parking
brake.
_ Move motion control tever to neutrat (N} positior.
It_PORTA_t"[': THE MOTION CONTROL LEVER DOES
NOT' RETURN TO NEUTRAL (H) POSKION WHEN THE
CLUTCH/BRAKE PEDAL JS DEPRESSED.
o TOrestart movemenl, stowiy retease parking brake and
o Slowly move motion control lever to slowest setting.
o Make a! turns slowly.
TO TRANSPORT {See Fig= 1!}
When pushing or towing your tractor, be sure todisengage
transmission by placing freewheel control in freewneetng
position Free wheel control is located at th,e resr@awbar
of tractor.
o Raise attachment Iift to highest position with attach°
ment tift control.
o PuiJf_eewhee! controi knob out and hold in position by
inserting retainer spring into foP_uardhoie ofcontrol rod.
o Do not bush or tow tractor" at more than t:we{2} MPH.
° To reenijage transmission, reverse above procedure
_,_O'/'E: To protect isood from damage when transporting
your t:ac o_ on a truck or a traiter, be sure hood is closed
and sec ire Sto t_actor. Use an appropr a_emeans 9f tying
hood o t_actor (rope co_d, etc.).
CHECK ENGINE OIL L£VEL (See Fig. 17}
rise engine t-yoJ_ t<ac or has been shipped, from the
factory, already flied ws summ,e_ weight oii.
=, Check engne oii wh '.tae_oron ievei ground.
gffhread a_d _'emove o cap/dbstick wipe oil off
Re nse_-the a ps! ck <:to ;he tube and est oil fii! cap on
the tube. Do not h_ead the ei@onto Ihe tube. Remove
and read o! eve _:_cessary add oil un! 'FULL"
;na_k on d pstic_<is _esched Do r_otovert 1_
£or cold weather operation you st ould change oi! for
easier starling (See OL VISCOS TY CHARW n the
Castomer Ressonsl: ties section of this nanua0o
To change e _gine oi, see the C ;stomer Responsibifi-
ties section n t!qs Y,a .ai.

TO S_£R f ENGBIE (See Fig_ 9)
When starting d'_eengine for the first time or f the engine
has run out of f_.e, it will take extra crar_king time _omove
fuel from the tank to the engine.
_ Depress clutch/brake pedat and se_parking brake.
Place motion control lever in neutral (N) position.
b;iove attachment c!utch to "DISENGAGED" position_
Move throttte control to choke (l_.i) position.
Note: Before starting, read the warm and cotd starting
procedures below.
o !nsert key into ignition and turn keyclockwise to"START"
positior_ and reiease key as soon as engine starts. Do
not ;un starter continuously for more than fifteen sec-.
ends per minute, tf the engine does not start after
several attempts, move throt£Je controJ to fast (@)
position, wait a few minutes and try again, f engine sfiIJ
does not start:, move the throttJe controi back to the
choke (t'q) position and retry',
PURGE TRANSMISS_ON
To ensure proper operation and perfomlance, it is recom-
melsded that the transmission be purged before operating
tractor' for the first time. This procedure wiit remove any
trapped air inside the transmission which may have develo
oped dudng shipping of your tractor.
_B._PORTANT:SHOULDYOUR TRANSMiSSiON REQUIRE
REMOVAL FOR SERVICE OR REPLACEMENT, IT
SHOULD BE PURGED AFTER REINSTALLATION
BEFORE OPERATING THE TRACTOR.
P'.acetractor saifeiyon tevet sudace with engine off and
parking brake set.
Disengage transmission by placing freewheel control
in freewheeling position (See "TO TRANSPORT" in
this section of manuai).
Sitting in the tractor seat, sta£ engine. After the engine
is running, move throttle controi _9 stow 0 position.
',/?ARM WE.A_sJ_::_ R oc'-_AR,TtxG___"/50° F arid above) With motion control iever in neutral (N) position, slowly
._,._mo move the ,_hrot.._.o troJto Ihe fastWhen engine s*a '_" _- ' ,_.r f_:_-, i
(@} position.
]"he attachments and ground ddve cart now be used. if
the engine does not accept the end, restart the engine
and allow itto warm up for one min£e using the choke
as described above.
COLD WEATHER STARTING ( 50° F and beow)
o When eng r_estarts, allow engine to run with the throttle
cont_oi n the choke (ikl) position unfit the engine runs
roughly, then move throttie control to fast (_) position.
This may require an engine warm-up period from
severaJ seconds to several minutes, depending on the
HYDROSTAT C TRANSMISSION WARM LIP
Before driving the unit in cold weather, the transmis.
sion should be warmed up as follows:
"_ Be sure the tractor is on level ground.
_ Place the motion control lever in neutrat.
Re/ease the parking brake and let the chJtch/brake
slowly return to operating position,
Allow one minute for transmission to warm up.
This can be done during the engine warm up
The attacf ments can also be used during the engine
warm.<@period afterthe transmission has been warmed
Ijp,
NOTE: If at a figh aititude (above :3000 feet) or in cold
temperatures (below 32 F) the carburetor fuel mixture may
need to be adjusted for best engine performance. See "TO
ADJUST CARBURETOR" in the Sewice and Adiustments
section of this manuak
disengage clutch/brake pedal:
,_ Move motion control iever to full forward position and
hold for five (5} seconds Move lever to futJ reverse
postion and hold for five (5) seconds. Repeat this
procedure three (3) times.
NOTRE:During this procedure there wiit be no movement of
drive wheels. The air isbeing removed from hydraulic drive
Move motion control lever io neutral (N) position. Shut °
off engine and set parking brake_
Engage transmission by placing freewheel control in
driving position {See"TO TRANSPORT' n this section
of r,_anual).
Sitting in the tractor seat, sfart engine. After the engine
s running, move throttie control io hail (1/2) speed.
With motion control tever in neu_rat (N) position, slowly
disengage clutch/brake pedak
o S!owiy move metion control /ever forward, after the
tractor moves approximafe]y five (5) feet, slowly move
motion contm_ bver to reverse position. After the
tractor moves approximately five (5) feet return the
motion controi _everto the neutraJ (N) position. Repeat
this procedure with the molion controt lever three (3)
times,
'Four tractor is now purged and now ready for normal

OPER ]ON
V OW NG TIPS
o Tirechainscannotbe usedwhen themower housingis
attachedtotracto__,
_ Mower shouldbe properlyleveledforbest mowing
performance. See"TO LEVEL MOWER HOUSING _'n
the Sewice and Adiustments section of this manuai.
Fhe left hand side of mower shoutd be used for trim-
ruing.
o Driveso thatcfippingsae dischargedontothearea
thathas been cuL Have thecutarea.totherightofthe
tractor.Thiswi!lresultina more even distributionof
clippingsand morn uniformcutting,
When mowing largeareas,startbyturningtotheright
so thatciippingswilldischargeaway from shrubs,
fences_driveways,e_c.Afterone ortwo rounds,mow
inthe oppositedirectionmaking lefthand turnsunti
finished(See Fig _2 )
o Ifgrassisextremelytail,itshouldbe mowed twiceto
reduce oad and possiblefirehazardfrom driedclip-.
pings.Make firstcutrelativelyhigh;thesecond o the
desiredheight.
o Do notmow grasswhen its wet. We[ grasswillplug
mower and leave undesirable clumps: A!tow grass to
dry before mowing.
o Always operate engine at full throttle when mowing to
assure better mowing performance and proper dis-
charge of ma_eriat Regulate ground speed by seiect_
ng a low enough gear to give the mower cutting
performance as v_ellas the quaiity of cut desired.
o When operating etlachments, select a ground speed
that will suit the terrain and give best perferrnance of
the attachment being used.
_1ULCH_NG _._fOW_NGT_PS
_PORTANT: r.JR B.__ PERFORMANCE KE£1_
,_,_OWERHOUSING FREE (Yx BU}LT-UP GRASS AND
TRASH CLEAN At:TEl E_.CH USE{
The speciai muiching b_ade wilt recut the grass clip.
pings many times and reduce them n size so that as
un_,_th_ _awni:-_eywill d sperse rite the grassthey faii ..... " _ '
and not ,._._'_noticed. Aiso_ the mutched grass will
u,ua_g d_e quickiy to !J,o_ ,_e nutrients for the awn.
Always mulch witb_your '_* _<÷
,lg,_,_.., engine (Made) speed
as this wiiI provd_.Sthe best recutting action of Ihe
biades,
Avoid cutting your iawn when itis weL Wet grass tends
to form chimps and inte_eres with the mulching action.
The best time to mow your !awn is the early afternoon°
At this time the_a _' _-_ d ......
:er_s,:_nao ,Jie._ c:nd ne new y cut area
wiil not be exposed to the direct sun.
oorbest re_utts, adjust the mowe_ cutt ng he ght so that
the mower cuts off only £he top one-third of the grass
biades (See Fig. i2A). F:>rextrerneiy heavy mulching,
_'educeyour width of cut and mow slowly.
condkions may re-.
a second time to
eornpie e y hide the clippings. When doing a second
cui, mew across or perpend cuiar to the firsi cut path.
Change your cutting pattern from week to week. Mow
north te south one week then change to east to west the
next we_.K. This will i'ep prevent matting and oraininc
el the awn,.
itaAx _/s
FIG. 12

ER REI tLITtES
Check Brake Operation
[
L Check Tre Pressure
Check for _Bose Fasteners
Shaq:.ten/Reptace Mower Blades
Lubrication Cha4
Chock Battery Lovei/Recharge
i- Clean Balery and Terminals
k
i Che_k Transaxie Cooiin 9
Adjus Blade Beit(s) Tension
Ad ust Motion Drive Bek(s) Tension
Check Engine Oil Love
I Cha%ge Engine Oil
i
C ean Air F;ter
i...............................................
i Clean Engine Coo!ing Fns
Replace }park PN_g
Bapl
Replace Fuel Fiiter
............_ ............ .......' I.......... :>- i
[ _IW ¢W
i LJ2_
-Change more often when operatk! 9 under a hea,_ fioad ot in high all bienl tempera{urea.
2 - Service more often vw_en oeerating in dirty or dusty cot _Jitions.
3 If eaaipped wilh oil filte_ change oi every 50 hours
4 - Replace blades more oHen when mowing in sandy sol.
SERVICE DATES
, F
L
I
5 - If equipped with ad ustabie system,
I
/
F--
I
!
f
6 - Not red,sired if equipped with maintenance-free battely.
7 Tirhtep frort axle pivot bolt to 35 ft,-Ibs< maximum
Do not overt ghten
GENER£L REOOMME , ©AXIONS
The warranty on this tractor does not cover items that have
been subjected to operator abuse oF negligence. To
receive futIvalue from _hewarranty, operator must maintain
tractor as instructed in this manual
Some adjustments win need _o be made periodicaily to
properly maintain your tractor.
All adjustments in the Sen/ice and Adjustments section of
this manual should be checked at least once each season.
Once a year you should replace the spark plug clean
or replace air filter and check blades and belts for
wear. A new spark plug and clean air filter assure
proper air-fuel mixture and help your engine run better
and last longer.
BEFOR_ BACH US_
_,.,l_ec_..r,glne oil level
,., _,:;.!4 tlre pressure.
,_ Chec( for Bose !asteners

ES
TO SHARPEN BLADE (See Fig, '14}
Always observe safety rules when performing any mamte_
nance.
BRAKE OPERATION
_ttractor requires more than six f6} feet stooping distance
st h_ghsseed in hignesx gear. then brake must be adjusted.
See "TO ADJUST BRAKE' '_ the Service and _,djusP
rnents section of this manua_l.
T_RES
o Maintair proper a_rpressure in alt tires ISee 'PROD-
UCT SPECIFICATIONS" on page 3 of this manuah.
o Keep tires free of gasoline_ oil, or insect control chemi-
cals which can narm rubber,
Avoid stumps, stones, deed ruts. sharp objecls abe
omer nazaras that may cause tire damage.
Sate £n}uld be _aKento keeu :he blade oaancedo An
unbalanced blade w_!cause excesswe wbration and evem
_ual eamaae [o _ewe_ ar_aengine.
The blade can be sharpened with a file or on _grinding
wheel Dc not attempt to sharpen while on the mower.
To check blade rsa_ance,you _al_neecJa 5/8" diameter
steei bott ore. or acone oaiancer. When using a cone
bB]ancer. 1oucw [he nstructlons sursoJied with oaf
3RcBrL
o Slide blade on to an unthreaded portion of the stee! bott
ar p_nano hold the Boltor pm natalie with the g ouna.
I blade _sbatanced _1snoutct remain tn a horizontal
eosition, f either ena of the blade moves downwaro.
sharpen the heavy ena until the blade is Balanced.
NOTE: Do not use a nail for balancing blade. The _oDesof
En<_cen_e_"hole may aE;oearto De cen'iered but are no_
BLADE CARE
For best results mower blades must be Rep; snarD. Re--
p_ace Den[ or aamagea blades.
BLADE REMOVAL (See Fig, 13)
Raise mower to highest position to allow access to
blades.
o Remove hex bolt, iock washer and fiat washer securing
blade.
o InstaJt new or resharpened blade with traiting edge up
towards deck as shown,
Reassemble hex bolt, lock washer and flat washer in
exact order as shown.
o Tighten bolt securely (30-35 Ft. Lbs. torque).
IMPORTANT: BLADE BOLT iS GRADE 8 HEAT TREATED.
NOTE: We do not recommend sharpening blade - but ifyou
do be sure the blade is balanced.
BLADE\MANDREL
ASSEMBLY
FLAT'WASHER
LOCK WASHEF
HEXBOLT
(GRADE8) ..... _.,_ '@
*A GRADE 8 HEAT TREATED BOLT CAN BE
IDENTIFIED BY S1XLINES ON THE BOLT HEAD.
FIG. 13
CENTER HOLE
518" BOLT
OB P_N
BLADE
FIG. 14
I
J
Your tractor has a baSeR/charging system which is suffi-
cient for normal use However, periodic charging of the
battery with an aulomolive charger will extend its iile.
o Keep battery and terminals ctean.
Keep battery bolts tighL
Keep srnail vent holes open.
o Recharge at 6q0 amperes for 1 hour.
TO CLEAN BATTERY AND TERMINALS
Corrosion and dirt on the batteB_and terminals can cause
the battery to 'leakf power.
Open batten/box door°
o Disconnect BLACK battery cable first then RED bat-
ten/, cable and remove battery from tractor
o Rinse the battery with piain water and dry.
Clean terminals and batters/cabte endswith wire brush
until bright.
o Coat terminals wi'thgrease or petroleum jetly,
Reinstail batte_ {See "CONNECT BATTERY" in the
Assembty sect;on of this manual),
Check V-beits for deterioration and wear after 100 hours of
operation and replace if necessary. The belts are not
adiustabie Replace betts if they be@p,to slip from wear.

TRANSAXL£ COOUNG _
The fan and cooing fins of transmission should be kept
clean to assure proper cool r g.
Do not atte npt to ciean fan or transmission white engine is
run, ring or whiie the transmission is hot.
_nspect cooiing _anto be sure fan blades are intact and
clean
,, Inspect cooling fins for did, grass ciippings and other
materials. To p_event damage to seals, do not use
compressed air or high pressure sprayer to clean
Use gauge on oil fill cap/dipstick for checking level.
insert dipstick intothe tube and rest the oil fill cap on the
tube Do not thread the cap onto the tube when taking
Keep oil at 'FULL" iine on dipstick. Tighten
cap onto the tube securely when finished.
_COVER KNOB
A_RCLBANEB
COVER NUT
The l:ransaxle was seaied al the !actory and fluid mainteo
nance s not required forthe lie of thetransaxle Shouidthe
transaxie ever ieak or require serv cing, contact your near°
est aulhodzed service center/department.
LUBRICATION
Only use hgh quaiity det:e_gent oit rated with APi sewice
classification SF or SG. Select ire oi's SAE viscosity grade
according to your expected operating temperature.
FiG, 15
NO°FE: Al[hough r_rutti°viscosity ois (5W30, 10W30 etc.)
improve sta£ing in coJd weather these multi viscosity oils
wiiI resutt in increased oii consun pt on when used above
32'ff:. Check your engine oil level more frequently to avoid
possible engine damage from running !ow on oil.
Change the oil after the first two hours of operation and
every 50 hours hereafter or at ieast once a year if he
tractor is not used for 50 hours in one year.
Check the crankcase oil evet before sta_ing the engine
and a!ter each eight (8) hours oi operation. Tighten oil fitt
cap/dipstick secureiy each time you check the oil level
TO CHANGE ENGINE OIL (See Figs. t5 and t6}
Determine temperature range expected before oit change.
All oii must meet API service classification SF or SG.
Be sure tractor is on tevei surface.
Oil wil drain more freely when warm.
o Catch oil in a suitable coniainer
Remove oil fin cap/dipstick. Be carefui no_to allow dirt
to enter the engine when chang ng oii.
_o, Remove drain plug
After oii has dra ned completely, replace oil drain ph_g
and tighten secureiy.
0 Refill engine wkh oil th:_ough ol fill dipstick tube. Pour
slowly. Do not overfill. For approximate capacity see
'PRODUCT SRECIF CATONS' on page 3 of Ihis
ment/£i.
BASE
CAP!D_PST{CK
}
f
/
F_G°16
CLEAN AiR SCREEN (See Fig. 16)
Air screen must be kept free of dirt and chaff to prevent
engine damage from overheating. Clean with a wire brush
or compressed air to remove dirt and stubborn dried gum
fibers.
A_R F_LTER (See Fig. 16)
Your ¢ngine will not run properly using a dirty air fitter.
Clean the foam pre-cleaner after every 25 hours of opera-
tion or eve_ season. Service paper cartridge every 100
hours of operation or every season, whichever occurs first.
Sen/ice air cieaner more often under dusty conditions.
,o Remove knob and cover.
,_ Remove wing nut and air cieaner from base.
TO SERVICE PRE-CLEANER
o Stide foam pre-cieaner off cartridge.
Wash it n !iquid detergent and water.
Squeeze ii dr},'in a c!ean cioti_.
_0 Saturate it in engine oil.Wrap it in clean, absorbent
cioth and squeeze to remove excess oil.

TOSERVICECARTRIDGE
Gently_apthefiatsideofthepapercartridgetodis-
_oagedirt. Donotwasnthepapercannageoruse
oressudzed _lr. as rots witl aamage the cartridge.
Replace a dirty, bent. or damagers ca_ridge.
Reinstall the pre_cleaner _cteaned and oiled1 aver the
paper cartridge.
Reasse mb!e air cleaner, wing nut. cover and tlgnten
knob securely.
CLEAN AIR _NTAKK/COOLING AREAS
To insure proper cooling, make sure the grass screen,
cooling finsl and other external Surfaces of the engine are
kept clean at all times_
Every' 100 hours of operation (more often under extremeIy
dusty, drty conditions), remove the blower housing and
other cooling shrouds. Clean the COOtingfins and extemai
surfaces as necessary. Make sure the cooling shrouds are O_LFILTER
reinstaIled. F_G_17
NOTE: Operating the engine with a blocked grass screen,
dirty or plugged Cooling fins, and/or Cooting shrouds re-
moved will cause engine damace_'gdue to everheatJng,.H-UNE FUEL F_LTER (S&e Fig, 18)
Inspect and replace corroded muffler and spark attester (if
equipped) as it could create a fi_e hazard and/or damage.
SPARKPLUGS
Replace spark plugs at the beginning of each mowing
season or after every 100 hours of operation, whichever
occurs first. Spark plug type and gap setting are shown in
"PRODUCT SPECIFICATIONS" on page 3 of this manual.
ENGINE OiL FILTER (See F:ig. 17}
Replace the engine oit filter every season or every other oit
change if the tractor is used more than 100 hours in one
year,
o Drain oil from engine crankcase (See _%OCHANGE
ENGINE OIL" in this section of this manual, through
step remove drain piug).
o Remove oil filter and wipe off filter adapter.
o Apply a thin coating of new engine oit to the rubber
gasket on replacement oil fitter.
, Install replacement oil filter on filter adapter. Turn oii
filter c!ockwise until rubber gasket contacts the filter
adapter, then tighten filter an addilionai 1/2 turn.
o Fill crankcase with new oil (See "TO CHANGE EN--
GINE OIL" in this section of this manual). For approxi-
mate capacity see "PRODUCT SPECIFICATIONS" on
page 3 of this manual
o Start the engine and check for oit baksl Correct any
leaks before piacing engine into fuil operation.
The fuel filter should be replaced once each Season. If fuel
filter becomes clogged, obstructing fuel flow to carburetor,
replacement is required.
o With engine cooJ, remove filter and plug fuel line
sections.
o Place new fuel filter in position infuel line with arrow
pointing towards carburetor.
o Be sure there are no fuel line leaks and clamps are
properly positioned.
o Immediately wipe up any spilled gasoline.
CLAMP CLAMP
FIG, 18
CLEANING
o Clean engine_ battery, seat, finish, etc. of ait foreign
matter.
Keep finished surfaces and wheels free of at! gasoline,
oil, etc:
Protect painted surfaces with automotive type wax.
We do not recommend using a garden hose to clean your
tractor unJess the electricaJ system, muffler, air filter"and
carburetor are covered to keep water out. Water in engine
can result in a shortened engine life.

CAUTION:BEFOREPERFORMINGANYSERVICEORADJUSTMENTS:
-Oepress clutch/brake pedal fully and se_ parking brake.
oP_ace motion contro_ _ever in neutra_ (N) position.
-Place attachment clutch in "D_SENGAGED" position.
Turn ignition key "OFF" and remove key.
_,_akesure the b_ades and all moving parts have completely atoppedo
©iscor_r_ect spark p_Jg w_re from spark pEugann place wire where it ¢annct come in con[act
with _ !:_.
TO REMOVE MOWER (See Fig, 19)
!lower wiil be easier to remove from the right side oftractor.
Place atlachment clutch m 'DISENGAGED" pos tion,
Move attachment lift Iever forward to lower mower to its
lowest ooslt_on.
Rotl belt off ename oui!ey,
Disconnect clutch rod [rom clutch Iever by removing
re[amer spnng.
Disconnect anti-sway o_r Irom cnass_s bracket ey
remowng relamer spring,
Disconnect susoens_on arms from rear OeCKbrackets
Dy removing retainer springs,
Disconnect tront inks from deck r_yremovfflg re_amer
sDnn(] S,
Raise lift lever to raise suspension arms. Slide mower
out ,from under trac[or,
Ri_POHTANT: IF AN ATTACHMENT OTHER THAN THE
ViOWER 1STO BE MOUNTED TO THE TRACTOR THE
R,H AND L.H, SUSPENSION ARMS MUST BE REMCVED
ROM TRACTOR.
t°O _NSTALL MOWER (See Fig. t9}
Raise attachment lift lever to its highest position.
Slide mower under tractor with discharge guard to right
side of tractor,
Lower lift lever to its lowest position.
instal] mower in reverse order of removal instructions.
CLUTCH
CLUTCH LEVER
RETAINER
SPR_NG
ENGINE
/PULLEY
RETAINER
SPRING
ANTFSWAYBAR RETAINER
SPRINGS
(BOTH SIDES;
FIG. 19
j.-