Crane MMB-AE8A-12101 User manual

Press FEED button to increase level and UNLOAD to decrease it. In order to switch
between feed and unload settings press two buttons simultaneously.
When setting is done set SW2 to OFF. Unit will switch to normal operation. No power
cycling is necessary.
BILL ENABLE OVERRIDE RULES:
The following is implemented for the Universal Recycler to enhance sales while still
preventing dispensing of small coins. The Machine’s VMC will automatically limit
acceptance and stacking of bills when it calculates there is insufficient change for the
transaction.
These rules act to disable 10AED, 20AED, 5USD, 10USD, 20USD, 5GBP, 10GBP
5EUR, 10EUR, 20EUR bills, when the Universal recycler calculates that there are
insufficient bills and coins to provide change. Three red short blinks will be showed
in this case. Override rules could be disabled by switch 2.2.
Two red short blinks will be showed in case of rejecting of banknote because it was
disabled by VMC.
Denomination being accepted When to override enable form machine’s VMC
20AED, 10AED
5USD, 10USD, 20USD,
5GBP, 10GBP
5EUR, 10EUR, 20EUR
Override machine enable of denomination if there
is not enough change or payout of small coins(less
1AED) is above 5AED.
5AED, 1USD Never override machine enable
If number of bills in the recycling cassette more than 4, then the recycler will modify
dispense command for coins to dispense it in bills.
OPTIONAL ACCESSORIES AND DOCUMENTS:
•CASHCODE BILL SET
Description Part# BSD- AED3EUR3GBP2USD4-B
•CASHCODE Bill Validator MDB
Protocol Interface Descriptions Part# MAN-MDB
2720 Steeles Avenue West, Units 2-3, Concord, ON, Canada, L4K 4S3
TEL: [phone]
FAX: [phone]
Web Address: www.cashcode.com
Email: [email protected]
2015 CashCode A Crane Co. Company. PT# UG-MMB-AE8A-12101_C.doc 03/15
MMB-AE8A-12101
Software Description
CURRENCY:
5, 10, 20 United Arab Emirates Dirham (AED)
5, 10, 20 EURO (EUR)
5, 10 English Pound Sterling (GBP)
1, 5, 10, 20 United States Dollar (USD)
(see Bill Set Descriptions BSD-AED3EUR3GBP2USD4-B
for more details)
Currency Processing Data version – 01 (09/09/2014)
EXTERNAL COMMUNICATION INTERFACE:
MDB interface
New 10 EUR (2014) Ready!

EXTERNAL COMMUNICATION INTERFACE FEATURES:
MDB INTERFACE
•Country Code = 1784h
•Decimal Place = 2
•Scaling Factor = 100
•Bill Types Credit :
Currency Note Note Value (AED)
USD $1 3 AED
USD $5 15 AED
USD $10 30 AED
USD $20 60 AED
GBP £5 25 AED
GBP £10 51 AED
EUR €5 21 AED
EUR €10 43 AED
EUR €20 86 AED
DIP SWITCHES SETTING*:
SW. #1 ON state OFF state Default
Setting
SW1.1 5 USD Disable 5 USD Enable OFF
SW1.2 10 USD Disable 10 USD Enable OFF
SW1.3 20 USD Disable 20 USD Enable OFF
SW1.4 5 GBP Disable 5 GBP Enable OFF
SW1.5 10 GBP Disable 10 GBP Enable OFF
SW1.6 5 EUR Disable 5 EUR Enable OFF
SW1.7 10 EUR Disable 10 EUR Enable OFF
SW1.8 20 EUR Disable 20 EUR Enable OFF
SW. #2 ON state OFF state
SW2.1 High Security High Acceptance OFF
SW2.2 Override rules disabled Override rules enabled OFF
SW2.3 Reserved Reserved OFF
SW2.4 Service Mode To work with a “Host
Machine Controller” OFF
*1 USA and 5, 10, 20 AED are always enable.
RECYCLING CASSETTE CONTROLS:
The Recycling Cassette controls are shown on the drawing below.
RECYCLING CASSETTE DIP SWITCHES SETTING:
Switch ON state OFF state Default Setting
SW1 Assign for 10 AED Assign for 5 AED OFF
SW2 Cassette setup mode Normal operation OFF
RECYCLING CASSETTE INDICATOR:
After power on Recycling cassette indicator shows control firmware version:
F1 -> 21
After initialization indicator shows number of bills inside of the recycling cassette.
In case of an error it will start flashing showing consequently number of bills and one
of the following error codes:
E0h – there was a hardware error detected
E1h – no communication with Coin Changer. In this case device will emulate Coin
Changer with 1 tube (5 AED or 10 AED).
FEED/UNLOAD BUTTONS:
The Feed button is used for setting a Loading mode. This mode makes the
entered bills of a selected denomination to be loaded into the recycling cassette. To
cancel a loading mode, the Feed button must be pressed again. If bills do not enter
within 20 seconds, the loading mode will be canceled automatically.
By pressing the unload button one bill will be dispensed from the recycling cassette
through the entry channel. If the feed and unload buttons are pressed simultaneously
then all bills will be unloaded from the recycling cassette into the drop cassette.
RECYCLING CASSETTE SETUP MODE:
Recycling Cassette setup mode allows user to adjust recycling cassette feed and unload
levels (maximal number of bills accepted into the cassette and number of bills to be left
in the cassette during unload operation correspondingly) without need of special
equipment. In order to enter the setup mode set SW2 to ON. The cassette indicator will
start blinking “FL”(Fill level) or “UL”(unload level) and the set level consequently.
DIP Switches
Unload button
Feed button
LCD display