Crane currenza MB-US88-4.05C User manual

SUPPORT OF BILL RECYCLER COMMAND SET:
The Universal Recycler supports bill recycler command set and works
in MDB Level 2 only.
If recycled denomination was set by MDB command, then reset or power up re-assign it
to 1$.
MDB Level and recycled denomination cannot be changed by Configuration card.
OPTIONAL ACCESSORIES AND DOCUMENTS
•CASHCODE BILL SET Description Part# BSD-USD3-A
•CASHCODE Bill Validator MDB
Protocol Interface Descriptions Part# MAN-MDB
2720 Steeles Avenue West, Units 2-3, Concord, ON, Canada, L4K 4S3
TEL: [phone]
FAX: [phone]
Web Address: www.cashcode.com
Email: [e-mail]
2013 CashCode A Crane Co. Company PT# UG-MB-US88-4.05C_A.doc 08/13
MB-US88-4.05C
Software Description
CURRENCY:
1, 2, 5 United States Dollar (USD)
(see Bill Set Description BSD-USD3-A for more details)
EXTERNAL COMMUNICATION INTERFACE:
MDB interface
Currenza Universal Recycler

EXTERNAL COMMUNICATION INTERFACE FEATURES:
MDB INTERFACE
•Country Code = 1840h
•Decimal Place = 2
•Scaling Factor = 100
DIP SWITCHES SETTING:
Switch ON state OFF state Default
Setting
SW1
Reserved
Reserved
O
N
SW2
Reserved
Reserved
O
N
SW3 Reserved Reserved ON
SW4
Reserved
Res
erved
O
N
SW5
Reserved
Reserved
O
N
SW6 Reserved Reserved ON
SW7 Reserved Reserved OFF
SW8 Service Mode To work with a “Vending
Machine Controller” OFF
.
RECYCLING CASSETTE CONTROLS:
The Recycling Cassette controls are shown on the drawing below.
RECYCLING CASSETTE DIP SWITCHES SETTING:*
Switch ON state OFF state Default Setting
SW1
Reserved
Reserved
OFF
SW2
Cassette setup mode
Normal operation
OFF
*Recycling cassette is always assigned to 1$.
;
RECYCLING CASSETTE INDICATOR:
Recycling cassette indicator shows number of the bills inside of the recycling cassette. In
case of an error it will start flashing showing consequently number of bills and one of the
following error codes:
E0h – there was a hardware error detected
E1h – no communication with Coin Changer. In this case device will emulate Coin
Changer with 1 tube (1$ US).This feature not active in Recycler mode.
E2h – Recycling Cassette operations are disabled if jam occurs (1 red flash is blinked
on bezel every 4 sec).
FEED/UNLOAD BUTTONS:
The feed button is used for setting a loading mode. This mode makes the entered bills of
a selected denomination to be loaded into the recycling cassette. To cancel a loading
mode, the feed button must be pressed again. If the bills do not enter within 20 seconds,
the loading mode will be canceled automatically.
By pressing the unload button one bill will be dispensed from the recycling cassette
through the entry channel. If the feed and unload buttons are pressed simultaneously then
all bills will be unloaded from the recycling cassette into the drop cassette.
If the feed or unload button is pressed and held for 4 sec. then the unloading or
dispensing mode is interrupted.
RECYCLING CASSETTE SETUP MODE:
Recycling Cassette setup mode allows user to adjust recycling cassette feed and unload
levels (maximal number of bills accepted into the cassette and number of bills to be left
in the cassette during unload operation correspondingly) without need of special
equipment. In order to enter the setup mode set SW2 to ON. The cassette indicator will
start blinking “FL”(Fill level) or “UL”(unload level) and the set level consequently.
Press FEED button to increase level and UNLOAD to decrease it. In order to switch
between feed and unload settings press two buttons simultaneously.
When setting is done set SW2 to OFF. Unit will switch to normal operation. No power
cycling is necessary.
CURRENZA CONFIGURATION CARDS:
•Fill in configuration card blocks as needed, use black pen or marker.
•Place DIP switches 1 through 6 in ON, switches 7 and 8 in OFF and
power-up recycler.
•Remove the drop cassette.
•Place configuration card into bezel, all the way in.
•Mount drop cassette, unit will take the card right in and give a blinking pattern.
•4 long BLUE flashes means Ok.
•4 long RED flashes means wrong Config.Card
•“N” short RED flashes means error in row “N” of Configuration Cards.
Two red short blinks will be showed in case of rejecting of banknote because it was
disabled by VMC.
DIP Switches
Unload button
Feed button
LCD display