Creative Play HS112 User manual

REF: HS112
pg 1 of 18 31.07.2019
HS112 - OCTAVIA HALF (5M)
Installation Instructions

REF: HS112
pg 2 of 18 31.07.2019
SEATING & SIDES PARTS / ASSEMBLIES
UPRIGHT TIMBERS
PARTS REQUIRED
SIDE ASSEMBLIES - QTY x 4
SA
SEAT SLATS - INNER (SET) x 2
SS-I
SEAT SLATS -END (SET) x 2
SS-E
SEAT SUPPORT ASSEMBLY x 3
SSA-I (INNER)
SEAT SUPPORT ASSEMBLY x 2
SSA-E (END)
UPRIGHT MAIN TIMBER
UPRIGHT ADDITIONAL
UMT - QTY x5
UAT - QTY x7

REF: HS112
pg 3 of 18 31.07.2019
FSA - a - QTYx2 (1 x ar / 1 x al)
FSA - b - QTYx2
FSA - c - QTYx2 (1 x cr / 1 x cl)
FSA - d - QTYx1
PARTS REQUIRED
FLOOR PARTS / ASSEMBLIES
x70
x282
x64
97.M8X120CSK
97.M8X80CSK
97.M8X180CSK
x480
97.D4.5X60 (DECK SCREW)
FA-a - QTYx2
FS-A - QTYx2
FS-B - QTYx2
FD - QTYx21 SLATS
FLOOR - DECKING
FD
FLOOR ASSEMBLY
FA
FLOOR SURROUND ASSEMBLY
FSA
FLOOR SUPPORTS
FS

REF: HS112
pg 4 of 18 31.07.2019
PARTS REQUIRED
ROOF BRACES
ROOF ASSEMBLIES
RA
ROOF SUPPORTS
RS
RB
ROOF TRIM / KING ‘POST’
RT
ROOF MAIN SUPPORTS
RM
QTY x 1 - RT1 - ROOF CAP
QTY x 1 - RT2 - KING POST
QTY x 3 - RT3a - 6x1 TRIM
QTY x 2 - RT3b - 6 x 1 TRIM
QTY x 4 - RT3c
QTY x 2 - RT4
QTY x 1 - RT5
QTY x 4 - RA - ROOF ASSEMBLIES
QTY x 5
QTY x 4 - RS - a
QTY x 1 - RS - b
QTY x 5

REF: HS112
pg 5 of 18 31.07.2019
FOUNDATION DETAILS
FGL
UMT UAT
NOTES:
POST HOLES 400MM x 400MM

REF: HS112
pg 6 of 18 31.07.2019
INSTALLATION INSTRUCTIONS
1
2ATTACH FSA - d TIMBER TO REINFORCE FSA TIMBERS SHOWN
POSITION FSA ASSEMBLIES
USING 4X M8X180MM WOOD SCREWS, ENSURE SCREWS ARE INSERTED FROM INSIDE FRAMEWORK
POSITION THESE ON THE GROUND 120MM FACE ON THE OUTSIDE
FSA - al
FSA - ar
FSA - b
FSA - b
FSA - cl
FSA - cr
FSA - d

REF: HS112
pg 7 of 18 31.07.2019
INSTALLATION INSTRUCTIONS
3
4SCREW THE FAS ASSMBLIES TO THE UMT TIMBERS
INSTALL THE UMT TIMBERS
USING - 97.M8X120CSK - QUANTITY X 20
THE 90X90 TIMBER ON THE FSA ASSEMBLIES HELP POSITION THESE
FSA
UMT

REF: HS112
pg 8 of 18 31.07.2019
INSTALLATION INSTRUCTIONS
5
6INSTALL FA - a ASSEMBLIES
INSTALL ONE UAT TIMBERS IN CENTRE OF FSA - d TIMBER
USING - 97.M8X180CSK - QUANTITY X 2
USING - 97.M8X180CSK - QUANTITY X 16
FSA - d
NOTES:
TOP FACE OF TIMBER WILL BE FLUSH WITH THE
TOP OF THE ‘INNER’ 90X90 TIMBER

REF: HS112
pg 9 of 18 31.07.2019
INSTALLATION INSTRUCTIONS
7
8INSTALL FLOOR SUPPORTS FS - a & b
ATTACH ADDITIONAL SUPPORTS
USING M8X180MM WOOD SCREWS
USING 2 X M8X180MM PER TIMBER - SCREWING INTO THE FA ASSEMBLY
FS - a
FS - b
FS - b FS - b
FS - a FS - a

REF: HS112
pg 10 of 18 31.07.2019
9
10 ATTACH RM TIMBERS TO KING POST (RT2) AND SCREW TO UPRIGHTS
ATTACH THE RS - a ROOF TIMBERS
USING 2 X M8X120MM & 2 X M8X180MM WOOD SCREWS
USING 2 X M8X80MM WOOD SCREW EITHER END, ENSURE TIMBERS ARE POSITIONED AS SHOWN
INSTALLATION INSTRUCTIONS
NOTES:
ENSURE TIMBERS ARE PRE-DRILLED AND
COUNTERSUNK
TIMBERS ARE POSITIONED LEVEL WITH THE
TOP OF THE UPRIGHT TIMBER
RS - a
NOTES:
ENSURE SCREWS ARE AS SHOWN TO
RIGHT, TAKE CARE NOT TO SPLIT
UPRIGHT TIMBER
2X 180MM SCREWS PER END
2X 120MM PER TIMBER

REF: HS112
pg 11 of 18 31.07.2019
11
12 ATTACH THE RA-L / RA-R ASSEMBLIES TO THE RM TIMBERS
REPEAT FOR THE REMAINING RM TIMBERS
USING - 97.M8X80CSK - QUANTITY X 8 (INTO EACH RM TIMBER EITHER SIDE)
USING 120MM SCREWS INTO THE KING POST AND 180 SCREWS INTO THE UPRIGHT TIMBERS
INSTALLATION INSTRUCTIONS
RA-L
RA-R
RM
RM

REF: HS112
pg 12 of 18 31.07.2019
13
14 ATTACH RS - b TIMBER TO FRONT RM TIMBERS SHOWN
SECURE THE 2 SECTIONS OF ROOF (L - R) TOGETHER & REPEAT
USING 4 M8X180MM WOOD SCREWS
INSTALLATION INSTRUCTIONS
USING - 97.M8X80CSK - QUANTITY X 12 MIDDLE SECTION
NOTES:
REPEAT STEPS 12 & 13 UNTIL ALL RA
PARTS HAVE BEEN ATTACHED
RA

REF: HS112
pg 13 of 18 31.07.2019
RT3a
RT3a
RT3a
RT3b
RT3b
RT3c
RT3c
RT3c
RT3c
15
16 ATTACH THE RT4 & RT5 FRONT TRIM TIMBERS
SCREW TRIM TIMBERS TO THE MAIN ROOF SUPPORTS (RM TIMBERS)
USING 16 X M8X80MM, SCREW TO RM TIMBERS
USING 6 X M8X80MM WOOD SCREWS FOR EACH SECTION
INSTALLATION INSTRUCTIONS
FIG 1
FIG 2
NOTES:
RT3 - a / b / c TIMBERS ARE TO BE
POSITIONED AS SHOWN TO ENSURE THE TIMBERS DO
NOT CLASH - SEE FIG 1 - RT3-c SITS BELOW a/b
ENSURE OVERHANG IS AS SHOWN ABOVE - FIG 2
NOTES:
ENSURE RT5 TIMBER IS PLACED OVER
RT4 TIMBER AND SCREWED TOGETHER AS
SHOWN
TOP OF RT35 TRIM SHOULD BE FLUSH
WITH TOP OF TR3 TRIM SLATS ALREADY
INSTALLED
RT3 - a

REF: HS112
pg 14 of 18 31.07.2019
15
16 ATTACH ROOF BRACES - RB
USING - 97.M8X120CSK - QUANTITY X 4 PER TIMBER
ATTACH THE RT1 TRIM PIECE
USING 4 X M8X80MM WOOD SCREWS FOR EACH TIMBER
INSTALLATION INSTRUCTIONS

REF: HS112
pg 15 of 18 31.07.2019
17
INSTALLATION INSTRUCTIONS
INSTALL DECKING AS SHOWN BELOW
USING - 97.D4.5X60 (DECK SCREW) - APPROX 2MM BETWEEN EACH SLAT
NOTES:
WORK FROM FRONT TO BACK - SPACING APPROX 2MM
BETWEEN TIMBERS ENSURE EACH PIECE IS SCREWED TO
ALL SUPPORTS (DOTTED LINE)
NOTES:
USE 2 X DECK SCREWS FOR WHERE DECK IS SCREWED INTO
FLOOR SUPPORTS - GENERALLY 20 X DECK SCREWS PER
SLAT / TIMBER

REF: HS112
pg 16 of 18 31.07.2019
19
20 INSTALL SEAT SUPPORTS
ENSURE ENTRANCE HAS AN SSA-(END) EITHER SIDE
INSTALLATION INSTRUCTIONS
ATTACH SIDE ASSEMBLIES
USING M8X80MM WOOD SCREWS, ENSURE TIMBERS ARE PRE-DRILLED AND COUTNERSUNK
4 SCREWS PER SIDE AS SHOWN
SSA - E
NOTES:
USE 2 X M8X120MM WOOD SCREWS TO SCREW INTO THE
UPRIGHT TIMBER - FIG 3
FURTHER SECURE USING 2 X M8X120MM WOOD SCREWS,
POSITION THESE SCREWS ON THE ‘INSIDE’ AND SCREW INTO
THE GROOVE - FIG 4
FIG 4
FIG 3
SSA - I SSA - I
SSA - I

REF: HS112
pg 17 of 18 31.07.2019
21
22 FURTHER SUPPORT THE ROOF USING RB-T TIMBERS
USING - 97.M8X80CSK - QUANTITY X 4 PER ‘WEDGE’
INSTALLATION INSTRUCTIONS
ATTACH SEAT SECTIONS - SS-I &SS-E
USING 4X M8X80MM WOOD SCREWS PER SLAT, SEAT SECTIONS ARE IN SETS - a / b
NOTES:
SCREW INTO THE 43X43 TIMBER SUPPORTS
EITHER SIDE OF THE SEAT SUPPORT ‘UPRIGHT’
SS-Ia SS-Ia
SS-Ib SS-Ib
SS-Eb SS-EbSS-Ea SS-Ea
NOTES:
RB-T TIMBER BLOCKS SECURES /
SUPPORT THE ADJOINING ROOF
ASSEMBLIES

REF: HS112
pg 18 of 18 31.07.2019
23
INSTALLATION INSTRUCTIONS
INSTALLATION COMPLETE
PLEASE CHECK ALL SCREWS COUNTERSUNK / NEAT SAND ANY TIMBERS AS REQUIRED