Cretors CMT5A User manual

COATER-MIXER
1
176 MITTEL DRIVE, WOOD DALE, IL 60191
COATER / MIXER
MODEL CMT5A/CMT5E (14045)
120 Volt,
Single Phase, 60 Hz
230 Volt,
Single Phase, 50/60 Hz
READ and UNDERSTAND these operating and safety
instructions before operating this popcorn machine

COATER-MIXER
2
SAFETY FIRST
The information in this manual is essential for the safe installation and of
your Cretors popcorn machine. The manual must be read and understood
before installing, and operating this equipment, or equivalent training must
be provided.
"The employer shall instruct each employee in the recognition and avoidance
of unsafe conditions and the regulations applicable to his work environment
to control or eliminate any hazards or other exposure to illness or injury".
Ref.: 29 CFR 1926.20 (b)(4)(a)(2)
It is understood that safety rules within individual companies vary. If a
conflict exists between the safety procedures contained in this manual and
the rules of a using company, the more stringent rule should take
precedence.
I INTRODUCTION
This manual is filled with timesaving and money-saving information regarding your Cretors
popcorn machine. There is nothing, however, more important than the safety aids and warnings
that is found throughout this document. The Safety Alert Symbol is used to identify topics of
primary safety concern wherever they appear. Furthermore, a separate section has been included
which deals exclusively with operation and accident prevention.
If, after reviewing this manual, anything is unclear or technical problems are encountered, contact
the dealer from whom you purchased your machine for assistance and if there are any additional
questions, feel free to contact our Customer Service Department at the address and/or phone
number listed on the front and back covers of this manual. Always have the model and serial
number of your machine available to assist in obtaining the correct information.
II SAFETY ALERT SYMBOL
The symbol shown below is used to call your attention to instructions concerning your personal
safety and the safety of others. Watch this symbol. It points out important safety precautions. It
means "ATTENTION! Become Alert! Your personal safety is involved!" Read the message that
follows and be alert to the risk of personal injury or death.

COATER-MIXER
3
III PURPOSE OF MANUAL
This instruction manual is intended to familiarize owners with the operation
and safety procedures associated with your Cretors popcorn machine.
This manual should be kept available to operating personnel.
A person who has not read and understood all operating and safety
instructions is not qualified to operate the machine.
IV PRODUCT IDENTIFICATION
CRETORS COATER - MIXER –CMT5A-X; CMT5E-X (14045)
ELECTRICAL SPECIFICATIONS: Coater/Mixers are available in any of the following
Electrical configurations:
120Volt, Single Phase, 60 Hz
230Volt, Single Phase, 50/60 Hz.
MODEL CMT5A-X
COATER/ MIXER
Capacity:
5 Gallon Bucket of Popped Corn, approx. 2lbs
Electrical:
120V, 60Hz, 200 watts
Dimensions:
25”L x 26”W x 30”H
Net Weight:
40 lbs. (18 kg)
MODEL CMT5E-X
COATER/ MIXER
Capacity:
5 Gallon Bucket of Popped Corn, approx. 2lbs
Electrical:
230V, 50/60Hz, 200 watts
Dimensions:
25”L x 26”W x 30”H
Net Weight:
40 lbs. (18 kg)
V INSTALLATION
This machine should be placed in a prominent location and set reasonably level.
Do not connect to a higher voltage or different type current than indicated above
or damage will result for which we cannot assume responsibility.
Do not remove feet or block spacing under base so that unit can not pull air onto the
motor or the unit will over heat and shut down until it cools.

COATER-MIXER
4
VI OPERATION
To make a batch of cheese or flavored corn, proceed as follows:
1. Place two pounds of popcorn or one five-gallon bucket of popcorn into mixer bowl.
2. Turn on mixer switch. (if supplied with optional timer, turn timer clockwise to
desired time.)
3. Pour liquid cheese, powder cheese, or flavor mix over popcorn.
i. (Recommend two cups of liquid cheese melted with one cup of popping oil
mixed together or approximately one cup of dry cheese mix. A small amount
of oil can be sprayed on the corn if there is difficulty with the cheese sticking to
the corn.)
4. Wait until popcorn is coated evenly then shut off mixer switch.
To make coated nuts or any food product that may require flavor coating:
1. Place mixing blades over mixing shafts and install retaining clips.
2. Place nuts or products into mixing bowl.
3. Turn on mixer switch.
4. Pour mix over product.
5. Wait until product is coated evenly then shut off mixer switch.
VII TROUBLE SHOOTING
1. If bowl will not turn
(A) Is machine plugged in?
If Yes
(B) Is lighted switch “On”?
If Yes
(C) Make sure Bowl is properly placed on rollers.
(D) Check output of switch. There should be 120V. for domestic
machines and 230V. for export.
Voltage (No) Replace switch
Voltage (Yes) Check voltage at motor
If yes, replace motor
(E) Make sure cooling fan is operating. Agitating motor may shut down
and restart if overheats. If fan is not operating:
(F) Voltage at fan (No) check wiring.
(G) Voltage at fan (Yes) Replace fan.

COATER-MIXER
5
VIII CLEANING & SANITATION
Be certain the machine is turned ‘OFF’ and power is unplugged before sanitizing this
machine. Failure to do so could result in injury.
Clean unit every day. Perform the following:
Turn switch ‘OFF’ and remove electrical cord from wall supply.
Remove coating drum from machine. Also remove mixing blades and clips (if used). Wash in
hot soapy water, rinse, and dry.
Wipe all external surfaces with proprietary stainless steel cleaner or warm damp cloth and dry
thoroughly.
With drum removed, weekly turn the base over and assure the fan and fan grill (wire cover) are
clean and that fan is turning freely.
Replace drum.
Inspect wheels for wear and replace as required.
CAUTION: This appliance shall not be cleaned with a water jet.
This manual is filled with timesaving and money-saving information regarding your Cretors
popcorn popper. There is nothing, however, more important than the safety aids and warnings
found throughout this document.
If you have any questions, contact your local dealer and if there are any additional questions, feel
free to contact the Customer Service Department at C. Cretors and Company.
Additional copies of this manual can be obtained from C. Cretors and Company at the address
listed below. Please provide model and serial number when requesting additional copies of this
manual. There will be a nominal charge for additional copies.
Cretors guarantees this machine to be free of defects in parts, materials and workmanship for two
year. Please take this time to fill out the factory registration card and return it to the factory to
activate your warranty. If you have any questions concerning the Cretors' warranty, please contact
your local dealer or the Customer Service department at C. Cretors and Company.
C. CRETORS AND COMPANY
176 MITTEL DRIVE
WOOD DALE, IL 60191
PHONE [phone], FAX [phone]
WEB SITE: http://www.cretors.com Email: [e-mail]

R
A
A
2.000
ADHERE ANTI-SLIP
TAPE TO THE BOWL
7
1
SECTION A-A
SCALE 1 : 4
4
3
2
5
SEE ORIENTATION
IN THE TOP VIEW
6
NOTES:
XXX. 1.
REVISIONS
REV DC # APPROVED BY APPROVED ON
- - - -
- - - -
A - nvidojevic 08/20/2018
BILL OF MATERIALS
ITEM # QTY. P/N DESCRIPTION
1 1 14253-2 BOWL, 60 QUART, DRILLED
2 1 12816 REAR WHEEL SUPPORT / MIXER SHAFT
3 1 5743 1/4", MEDIUM SPLIT LOCKWASHER, 18-8 S.S.
4 1 10121 1/4-20 X 1/2"LG FULLY THD, HEX HEAD CAP SCREW, 18-8 S.S.
5 1 12835 MIXING BLADE, MIXER/COATER
6 1 12818 CLIP, RETAINING, RUE-24
7 1 21610 TAPE, ANTI-SLIP, 60 QUART BOWL
A A
B B
C C
D D
E E
F F
G G
H H
8
8
7
7
6
6
5
5
4
4
3
3
2
2
1
1
APPROVED DATE
DRAWN DATE
B SIZE DRAWING
STANDARD NOTES:
REMOVE SHARP EDGES AND BURRS. 1.
UNLESS SPECIFIED ALL DIMENSIONS ARE IN INCHES. 2.
REFERENCE DIMENSIONS ARE INDICATED IN PARENTHESIS. 3.
CRITICAL DIMENSIONS THAT NEED INSPECTION ARE INDICATED IN OBROUND BOX. 4.
T.S.C. STANDS FOR THEORITICAL SHARP CORNER & INS STANDS FOR INSIDE. 5.
FOR SHEET METAL, UNLESS SPECIFIED ALL DIMENSIONS ARE OUTSIDE. 6.
FOR SHEET METAL, FLAT PATTERNS ARE FOR REFERENCE ONLY. 7.
MINOR SCRATCHES ARE ALLOWED ON OPPOSITE SIDE OF MILL FINISH & #4 FINISH. 8.
APPROX.
WEIGHT
22.9
LBS
REFER INDIVIDUAL SUB-PARTS
MATERIAL
176 MITTEL DRIVE, WOOD DALE, IL 60191
www.cretors.com | www.flo-thru.com
DRAWN BY
A
ndarji
nvidojevic
08/20/2018
SHEET
14253
DRAWING NUMBER
DESCRIPTION
APPROVED BY
THIS DRAWING CONTAINS INFORMATION PROPRIETARY TO C. CRETORS & CO. AND IS FURNISHED IN CONFIDENCE FOR
SOLE PURPOSE OF SUPPLYING THE RECIPIENT WITH NEEDED ENGINEERING DATA. THE CONTENTS SHOULD NOT BE
DISCLOSED OR REPRODUCED IN ANY MANNER WITHOUT WRITTEN CONSENT OF C. CRETORS & CO. ALL RIGHTS RESERVED.
REVISION
BOWL, WITH MIXER, 60 QUART
1 OF 1
TOLERANCES
08/20/2018
0.02
0.01
1
+0.005 / -0
125Ra
x.xx =
x.xxx =
ANGLES =
HOLES =
FINISH =
THIRD ANGLE
PROJECTION

TEL: [phone] FAX: [phone]
3243 N. CALIFORNIA AVE., CHICAGO, IL 60618-5890
C. CRETORS & COMPANY
This drawing contains information proprietary to C. Cretors & Co.
disclosed or reproduced in any manner without the written consent
recipient with needed engineering data. Its contents should not be
and is furnished in confidence for the sole purposes of supplying the
of C. Cretors & Co. All Rights Reserved.
X.XXX
FRACT.
TOLERANCES
ALL HOLES
125
X.XX
+.005
-.000
FINISH
SURFACE
APPROVED
DRAWN BY:
DATE
CHK'D:
NAME:
REV.
SCALE:
REV:
MATERIAL:
DATE:
DATE:
B-
DWG. No.
BY
DESCRIPTION OF REVISION DATE
LGalvez
1/3/2008
= ±1/64
= ±0.005
±.5°
= ±0.020
12028 - JAM NUT
14194 - ADAPTER
12813 - WHEEL
12816 - SHAFT
12809 - MOTOR BOX ASSY.
14253 - BOWL COMPLETE W/ HANDLES
P/N 1605-1 - RUBBER FOOT
14172 - SHAFT & PLATE
12814 - WHEEL
12817 - SHAFT
12810 - ASSY.
12815 - DRIVE WHEEL
1274-C- FAN (230V)
1274 - FAN (120V)
CHEESE COATER - ASSEMBLY - CMT5
1/4"= 1"
CMT5
NOT SHOWN
12835- MIXING BLADE
12818- RETAINING CLIP
12829- NON SLIP TAPE
14190- MOTOR (120V)
B
14190-E MOTOR (230V)
14218
BASE SUPPORT
12816- REAR WHEEL SUPP.
MIXER SHAFT.