Crosswater Arcade US-H401-ARC User manual

Arcade Exposed Thermostatic Shower Set
US-H401-ARC
Introduction
Installation notes
Roughing-in dimensions
The installation must comply with all plumbing codes including local
codes. This valve is a mixing device and therefore requires the water
supplies to be reasonably balanced, otherwise a pressure-reducing
valve is recommended.
line pressures.
Installing shut-off valves on incoming supply lines is recommended
for ease of maintenance.
IMPORTANT: Turn off the main water supply before connecting
to any existing pipework.
WARNING! Please check for any hidden pipes and cables, electric
or otherwise,before drilling holes in a wall or floor.
Tools required
14"
1-1/8" - 3-3/4"
5-7/8"
D
H
C
O
L
T
O
38-3/8"
22-3/8"
Ø3/4"
6-3/4
Ø9-1/4"
Adjustable
wrench
Channel
locks
Plumbers’ putty
or caulking
Flat head
screwdriver
Cross head
screwdriver
Hexagonal
key
ON
OFF
ON
OFF
This exposed valve is suitable for use with all water systems up to a maximum
operating pressure of 72 psi and static pressure of 144 psi, beyond which
pressure-reducing valves must be installed.
The outlet is controlled by a flow control cartridge, commonly used for a main
shower head.
IMPORTANT: Please read these instructions carefully before beginning
installation and retain for future reference. These instructions have been
prepared for guidance. Please exercise due care at all times. We do not
accept responsibility for any problems that may occur through incorrect
installation.
Before beginning installation, check to ensure that no damage has occurred
during transport. Note: Damage claims cannot be made during or after
installation

US-H401-ARC
1 US-ARC V 21
2 US-ARC V 23
3 US-ARC V 24
4 US-ARC V 11_1
5 US-ARC V 17
6 US-ARC 31
7 US-ARC 1000EV
8 US-ARC _SHOWER
1
Component
2
3
4
5
6
7
8
57/8”COLD
INLET
HOT
INLET
13/16”
max
Remove the bottom nut from the valve body

Installation
Installation
Installation Instructions
Arcade Exposed Thermostat Riser Kit
Arcade Soap Dish For Riser
Arcade Handshower Cradle For Riser
Arcade Wall-mount Straight Shower Arm
Arcade 9" Shower Head
Arcade Handshower & Hose
Make sure that the hot and cold inlet pipes have been
installed correctly.
The inlet pipes should be perpendicular to the wall, have a
maximum length of 13/16”, are level and are 5-7/8” apart as
shown opposite.
Arcade Exposed Thermo Valve with Shut-off
Arcade Exposed Bottom Shut-off Outlet


holes (x4).


wall construction.
Connect the hot and cold water supplies and main outlet.
Once valve is installed, add the riser rail to the top outlet. To
install the bottom spout remove the stop located at the bottom of
Turn on the water supplies and test all connections for water
leaks.
Installation
Installation
4
SET SCREW
RISER
SOAP BASKET
ALLEN KEY
CRADLE SET SCREW
RISER
ALLEN KEY
Assemble the soap bracket & cradle onto the riser.

RISER
Cut if necessary.
Installation
5
Required
Height
ALLEN
KEY
SET
SCREW
RISER
SCREW WALL PLUG
BACK PLATE
RISER
2mm
2.5mm
SET SCREW
ALLEN KEY
SHOWER ARM
RISER
WASHER
Installation
6
Assemble the shower arm onto the riser.

Installation
7
Assemble the shower head.
Installation
8
Connect the hose to the valve body and put the handshower on the cradle.
6a
HANDSHOWER
HOSE
FILTER
WASHER
6b
SHOWER HEAD
WASHER
FILTER
SHOWER ARM

HANDLE
HANDLE
COVER CAPS
SCREW
THERMOSTATIC
CARTRIDGE
Replacement part
US-WLBGEXPVLVCAR
LOCKING
NUT
STOP
RING BRASS
RING
VALVE
COVER
HANDLE
HANDLE
COVER CAPS
SCREW
SET SCREW
The 1” concealed thermostatic valve should give trouble-free
service however servicing is a straightforward process.
To remove the thermostatic cartridge
Gently unscrew the cover cap from the handwheel.
Undo the long screw and dissasemble the parts as shown.
Undo the cartridge locking nut, (take note of the orientation of the
cartridge).
Pull the cartridge out of the mixer housing.
Wash the cartridge with clean running water and make sure that
any trapped debris has been removed.
Dry and lightly grease the seals, (only use silicone grease), and
replace the cartridge.
Re-assemble all parts.
9 Cleaning Instructions
Rinse away any traces of soap and gently dry with a clean, soft cloth after each use. Rinse completely with water and dry any overspray. This will
maintain the finish and avoid water spotting.
To remove mineral deposits, use a 50/50 solution of white vinegar and water. Do not allow the solution to soak on the product. Simichrome
Polish® contains a protective film to enhance maintenance and is helpful in preventing water spot buildup. Follow instructions to ensure
optimum results.
Never use an abrasive material such as a brush or scouring pad to clean the surface. The use of abrasive cleaners, cleansers or disinfectants will
alter the surface finish and void the warranty.
Do not allow certain materials such as toothpaste, cologne, shaving cream, nail polish remover, vinegar, wine, drain and glass cleaners to
remain on the surface. Prolonged contact will alter surface finishes and void the warranty.
We DO NOT recommend using any household cleaners as many can cause damage to the finish.
Please see the website for care instructions for specific finishes.
Maintenance for thermostatic valve US-ARC1000EV
NOTE: To avoid damage, please remove all plated parts before
maintenance takes place.
Thermostatic cartridges

Warranty - This Crosswater London product is covered by a limited lifetime warranty. For full details, terms and conditions please visit our website.
For further information contact:Crosswater London , 393 Fortune Blvd., Milford, MA 01757
Toll free number: 844-XWATER-1 (844-992-8371) tel: [phone] fax: [phone]
www.crosswaterlondon.com
email: [e-mail]
Issue date: 15092019
THERMOSTATIC
CARTRIDGE
Replacement part
US-WLBGEXPVLVCAR
Flow rate (PSI)
Flow rate (GPM)
1.5
1.3
2.6
3.9
5.3
6.6
8
3 4.5 6 7.25 14.5 30 44

ASME A112.18.1 / CSA B125.1
ASME A112.1016-2011 / CSA B125.16-11
Spare parts
Appliance standards/codesFlow rate