Crown Boiler CWD060 User manual

Gas-Fired, Direct Vent
Hot Water Boiler
AVAILABLE FROM:
DIMENSIONS (in inches)CROWN Co-axial Horizontal Vent Terminal
CWD SERIES SPECIFICATIONS
LOCATING THE BOILER
• Clearances: Sides 1”, front 3”, rear 1”, top 12”
• 6” clearance to air inlet collar when combustion air is supplied from indoors
• Boiler may be installed directly on a non-carpeted combustible floor
• Relief valve may not be moved from factory location
Important: This boiler requires a special venting system.
Read instructions carefully before installing.
Air inlet collar located on center rear of CWD193 through CWD245
Since 1949, homeowners have depended on us
for quality, value and service
3633 I Street, P. O. Box 14818
Philadelphia, PA 19134
Phone: [phone] Fax: [phone]
Visit us on the web: www.crownboiler.com
CWD-11/05-(20M)
PN980528R1
Heat Exchanger constructed and tested in accordance
with ASME Section IV standard.
1. Altitudes above 2,000 ft.–ratings should be reduced at a rate of 4%
for each 1,000 ft. above sea level (U.S.A. only), in Canada, boilers are
certified for altitudes up to 2,000 feet only.
2. Please specify fuel (natural gas or LPG).
3. Specifications and dimensions are subject to change without notice.
*
D.O.E IBR NET COLLAR
NO. OF AGA HEATING WATER DIAMETER WIDTH SHIPPING
Model SECS. INPUT CAPACITY RATING INLET EXHAUST A AFUE WEIGHT
BTU/HR BTU/HR BTU/HR. (inches) (inches) (inches) (%)
CWD060 3 60,000 51,000 44,000 4” 3” 16-1/8 85.1 280
CWD083 4 82,500 71,000 62,000 4” 3” 19-3/4 85.1 315
CWD110 5 110,000 94,000 82,000 4” 3” 23-3/8 85.2 350
CWD138 6 137,500 118,000 103,000 4” 3” 27 85.2 385
CWD165 7 165,000 142,000 123,000 4” 3” or 4” 30-5/8 85.2 420
CWD193 8 192,500 165,000 143,000 4” 3” or 4” 34-1/8 85.2 475
CWD220 9 220,000 189,000 164,000 4” 3” or 4” 32-3/4 85.2 525
CWD245 10 245,000 211,000 183,000 4” 3” or 4” 41-3/8 85.3 580

Horizontal
direct
venting
Horizontal
direct
exhaust
Horizontal
offset
terminal
option
Coaxial
vertical
direct
venting
Vertical
direct
venting
The advantages of sealed combustion
While the boiler in your home is heating, it requires about a room-full of air per hour for proper
combustion. Conventional boilers, installed in older houses or homes that are not well insulated, use
room air which is replaced through leaks in the wall or cracks around windows and doors. Room air,
however, is air that you have already paid to heat.
Direct vent “sealed combustion” boilers, in contrast, use a dedicated and sealed, fan-powered system
to draw air in from outside the house and to vent the products of combustion directly outside.
Sealed combustion boilers are ideal for new homes which are tightly insulated to conserve energy, as
well as for older homes that would like to improve energy efficiency.
Cabo2 offers a variety of venting options
Sealed combustion boilers are designed for through-the-wall venting where a chimney is not available
or when a chimney becomes unusable. Cabo2 is designed for direct venting but can be utilized as a
conventional induced draft boiler, and provides for venting options in both applications.
CROWN offers coaxial vent terminal kits for both horizontal and vertical venting. Consult our
installation manual for specific venting requirements.
The power of the Cabo 2 and the efficiency of
the Mega-Stor indirect water heater
Together, they assure you’ll have all the domestic hot
water you need, heated with more energy than is ever
available with direct fired water heaters. More energy
means more hot water.
Mega-Stor means…
•Abundant domestic hot water
•Heated by your high efficiency boiler to save energy
dollars
•Adjustable temperature control
•Well insulated to keep water hot for hours
•Removable cap for easy access to tank and coil
•Sizes from 26 to 119 gallons to meet every home and
apartment owner’s needs
•Lifetime full warranty on stainless steel coil and tank
assembly (See Mega-Stor warranty for details)
Cabo 2 and Mega-Stor…
made for each other
...ideal for today’s
homeowner who
is looking for a
more energy
efficient boiler
Energy Star qualified; efficiency exceeds 85% A.F.U.E.
Proven reliability: designed with the benefit of CROWN’s
years of experience, employing technology proven in service,
with the newest in controls to optimize operation.
Powered intake and venting
saves energy dollars by using combustion air from outside,
rather than room air you’ve already paid to heat, and assures
that all exhaust gases go directly outside.
System controller provides
two zones, with ability
to prioritize the zone
connected to a Mega-
Stor indirect water
heater. Plug-in
outdoor temperature
reset control is an
optional feature.
Self diagnostics, with
LED indicators, show
status of boiler
operation. Boiler may
be ordered without this
control system.
Pressure switch
monitors operation
of the venting system.
Electronic ignition–
Spark-to-pilot ignition
saves fuel. Step-
opening gas valve
provides smoother
ignition.
Sealed combustion:
isolates the combustion
in your boiler from the
air in your home.
Stainless steel burners
give quiet, trouble-free
operation.
Lifetime Limited
Warranty
on the heat exchanger.
(See Warranty for details)
Multiple venting options: through-wall venting for applications
where there is no chimney or where existing chimney is old and in
need of expensive repairs; horizontal or vertical installation to suit
most locations.
Clean look with controls
located in a front vestibule
for ease of service and flexibility
in installing the unit in tight spaces.
Advanced safety systems: designed
to assure clean,
safe combustion; reduces
the possibility of carbon monoxide
buildup.
Designed, tested and certified
to meet the industry’s most rigorous
standards of quality, safety and
efficiency.
Easy to install: completely factory
assembled, wired and tested.
Cast iron, wet-leg heat exchanger
provides efficient
heat transfer and reliability
over a long life.
Multiple location options:
can be installed on combustible floors
and, with its compact design and wet-
leg construction, can also be installed
in closets or small areas.
Sized to fit your needs:
eight sizes from 60,000
to 245,000 BTU/HR input
accommodate all sizes
of homes and apartments.